These rods and discs are precision ground to offer tighter tolerances than standard 6061 rods and discs.

An anodized coating forms a bond with the aluminum surface to improve wear and corrosion resistance.

Frequently used to make valve bodies, pistons, and hydraulic parts, 6020 aluminum is easier to machine and more corrosion resistant than 6061, but it is not as weldable.

As the strongest multipurpose aluminum we offer, 6013 aluminum has the same good corrosion resistance, weldability, and machinability as 6061 with increased strength. 6013 is often fabricated into high-stress machine parts.

Ready for turning in a lathe, these rods are precision ground and held to a strict straightness tolerance.

These rods are precision ground and held to a strict straightness tolerance, so they’re ready for turning in a lathe.

Precision ground and held to a strict straightness tolerance, these rods are ready for turning in a lathe.

The heavy duty construction provides more support than standard discs for heavy material removal.

Fit these discs over your tool's arbor to sand aluminum, soft metals, and nonmetals.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Holes allow dust removal when used with a vacuum sander.

With more flaps than standard discs, these last 30-40% longer.

A blend of cotton laminate and aluminum oxide creates a smoother surface than other grinding wheels with similar grits. Wheels are also known as Type 27 wheels and raised-hub wheels.

The flexible backing on these wheels conforms to curved and rough surfaces.

The saucer shape lets you hold these wheels at shallower angles than Type 27 wheels, so they’re more comfortable to handle. They are also known as Type 28 wheels and raised-hub wheels.

The special shapes of these wheels provide more clearance than typical straight wheels.

Use these wheels for light grinding, deburring, and sharpening.

Wheels remove more material than other grinding wheels with cotton laminate.

Bits thread onto mounted shanks so you can quickly switch head shapes without removing the shank. The abrasive grains are blended with rubber, which cushions during grinding to produce a smoother surface texture than other bits with similar grits.

The bits in this set have rubber blended into the abrasive, which cushions during grinding to produce a smooth to extra-smooth surface texture.

Set contains an assortment of tools for grinding, sanding, and cutting on small surface areas.

Diamond cuts more quickly, lasts longer, and leaves a finer finish than other lapping grains.

Choose these washers for their adherence to strict military standards for material and construction.

Use these metric washers to evenly distribute the load under bolt or screw heads and nuts when fastening. They can also act as spacers.

USS washers generally have a larger ID and OD than SAE washers.

Also known as backup washers, these are for use with blind rivets for extra support when fastening into soft material.

Create a stronger seal than metal or rubber alone. These one-piece washers are metal for strength with a bonded rubber seal that creates a tight grip.

These shims are made of layers of metal bonded with adhesive. Remove layers with a utility knife until you get the thickness you need.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts in aluminum, iron, stainless steel, and steel.

Made of premium grade abrasives, these wheels are strong and thick for making notches in aluminum, iron, stainless steel, and steel.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Run these high-density aluminum oxide wheels at higher speeds than standard cutoff wheels to make quick cuts in aluminum, iron, stainless steel, and steel.

Two layers of fiberglass mesh reinforcement give these wheels at least three times the life of standard cutoff wheels when cutting metal such as aluminum, iron, stainless steel, and steel.

Use these wheels for cutting soft metal, plastic, stone, and wood.

Use these wheels to cut through metal such as aluminum, iron, stainless steel, and steel.

Two layers of fiberglass mesh reinforcement give these fast-cutting, zirconia alumina wheels at least three times the life of standard cutoff wheels when aluminum, iron, stainless steel, and steel.

Use these clog-resistant wheels to make quick cuts in soft metal such as aluminum, brass, and copper.

Rigid, partially twisted bristles handle tasks such as edge rounding and removing weld slag, heavy surface contamination, and large burs. Also known as knot-wire brushes.

Remove light-to-medium rust and stains and small burs with these flexible-bristle brushes.

Rigid, twisted bristles handle tasks such as edge rounding and removing weld slag, heavy surface contamination, and large burs.

Made of phosphorus bronze that is Factory Mutual approved, these brushes inhibit sparking and are nonmagnetic and corrosion resistant.

Use on delicate surfaces.

Color code equipment and inventory.

An aluminum laminate protects these tags for outdoor use. Writing on these tags will leave impressions that are visible, even if the ink wears away.

Metal tags are more durable than plastic tags.

Metal tags are more durable than plastic tags.