We will reply to your message within an hour.
In addition to oil, these blended aramid fiber/Buna-N rubber gaskets resist water and aliphatic hydrocarbons such as ethylene.
Furnished with enough nuts and bolts to create a connection between two steel pipe flanges.
Aramid fibers and SBR rubber are blended for resistance to water, inert gases, and abrasion.
These blended aramid fiber/Buna-N rubber gaskets also resist water and aliphatic hydrocarbons such as ethylene.
Each gasket comes with enough bolts and nuts to create a connection between two steel pipe flanges.
Aramid fibers are blended with SBR rubber to resist inert gases. These gaskets also resist abrasion.
Often called controlled swell gaskets, these gaskets absorb water near the inside of the flange and swell to fill gaps. Use them on uneven surfaces, such as grooved, corroded, or pitted flanges.
Made from a blend of aramid fiber and Buna-N rubber.
Stronger and able to withstand higher pressures than other types of aramid/Buna-N.
Also resistant to inert gases and abrasion, this material is made from blended aramid fiber/SBR rubber.
Also resist aliphatic hydrocarbons, such as ethylene.
These grommets snap into place and have wings that expand against the sides of the hole to lock them in position. Use them to protect wire, cable, and cords by turning rough-edged and uneven holes into smooth holes.
The center hole has flaps that flex to hold and protect various sizes of wire, cable, and cords while keeping out dust and debris. Snap these grommets into place and their wings expand against the sides of the hole to lock them in position. Use them to turn rough-edged and uneven holes into smooth holes.
A slit in the side of these grommets allows you to install them around wire, cable, and cords that are already in place. They snap into the hole and their wings hold them tight. Use them to turn rough-edged and uneven holes into smooth, insulated holes.
Support shafts, bearings, and other moving parts that are routed through a hole. These grommets are slippery to allow parts to move freely in the hole. Install them on thin sheet-metal panels.
Select this plastic trim for its chemical resistance. Often used on panels, boards, signs, and mirrors, it protects edges from impact.
With a slippery surface, this trim minimizes friction between parts and is often used on conveyor rails, chutes, and guides. Made of plastic, it's also chemical resistant.
This trim is suitable for use in food preparation and processing environments. It's also chemical resistant. Use it to protect the edges of panels, boards, signs, and mirrors from impact in food processing applications.
Seal T-slots, rail ends, and gaps between rails to keep out dust, debris, and other contaminants.
These shelters are spring loaded, allowing them to retract and flex with trailers to provide a better seal than standard dock door shelters.
To provide more protection from the elements than dock door seals, these shelters wrap around trailers.
Made from glass-filled nylon for excellent wear resistance and strength.
Aramid and PTFE fibers are blended for seals that resist chemicals and abrasion. Use these seals in pumps.
Our most compressible packing seals, these require less pressure than any other to make an effective seal. They’re made of lubricated PTFE-impregnated aramid fiber and are for use in pumps.
The most abrasion resistant of all our packing seals, these are made of PTFE-impregnated aramid fiber that has been saturated in a lubricant. They are for use in pumps.
Since they require lighter packing pressure than standard oil- and water-resistant packing seals, these seals cause less friction and reduce shaft wear. They are for use in pumps and valves.
Made of durable material, these washers resist wear from rubbing and scraping surfaces.
As you tighten your screw, the rolled collar compresses under the head to create an insulating barrier between a screw shank and a mating surface.
These washers have a flat bottom and high walls to protect metal screw heads from electrical current.
Protect countersunk holes from damage and wear.
This Nomex aramid felt withstands temperatures three times as high as wool felt. It is chemical resistant and often used as insulation.
A blend of Aramid and fiberglass gives this sleeving excellent abrasion resistance. It can withstand temperatures up to 650° F
Made of Nomex fabric, this sleeving has excellent tear resistance and better abrasion resistance than nylon sleeving.
A spring extension prevents sharp bends and kinks in your cord, prolonging its life. These bushings, which are more rigid than grommets, shield cords from rubbing against the edges of holes in enclosures and panels, so they won’t wear down.
More rigid than grommets, these bushings guard cords from rubbing against the edges of holes in enclosures and panels and wearing down.