Bearings with Retaining Rings

Filter by

System of Measurement

Shaft Diameter

Shaft Mount Type

Bearing Seal Type

Ball Bearing Profile

Width

Bearing Trade Number

Bearing Type

For Load Direction

Inner Ring Type

Material

For Housing ID

Shaft Type

Dynamic Radial Load Capacity

Less than 10,000 lb.

10,000 lb. to 19,999 lb.

Bearing Construction

Single Row

Maximum Rotation Speed

Lubrication

Cage Material

U.S.–Mexico–Canada Agreement (USMCA) Qualifying

RoHS

REACH

DFARS Specialty Metals

Exempt

Export Control Classification Number (ECCN)

100 Products

Performance

Quick Mount

Slip onto a shaft and secure with the turn of a screw

70 products

Corrosion Resistant

Won't degrade from water or mild chemicals, such as ammonia

15 products

Environment

Food and Beverage

FDA-compliant or NSF-registered lubricant

15 products

Bearing Seal Type

Shielded

Covered enough to keep out large particles while dissipating heat

21 products

Quick-Mount Ball Bearings

Slip onto a shaft and secure with the turn of a screw. You don't need any special tools to mount these bearings.

Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.

Clamp-On Shaft Mount—The clamp tightens around the shaft for a strong 360° grip. These mounts attach more securely than set screws to reduce vibration. Plus, there aren't any screws pressing into the shaft, so it stays free from damage. Also known as a concentric lock.

Steel and Black-Oxide Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

				Retaining Ring						Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	OD	Thk.	Bearing Seal Type	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Bearing Trade No.		Each
Set-Screw Shaft Mount







				Steel

				1/2"	1 3/4"	5/8"	1.922"	0.042"	Sealed	Not Rated	2,550	5,000	-20	250	7608-2RS	4768K11	000000


				9/16"	1 3/4"	5/8"	1.922"	0.042"	Sealed	Not Rated	2,550	5,000	-20	250	7609-2RS	4768K12	00000
				5/8"	1 3/4"	5/8"	1.922"	0.042"	Sealed	Not Rated	2,550	5,000	-20	250	7610-2RS	4768K5	00000
				11/16"	1 3/4"	5/8"	1.922"	0.042"	Sealed	Not Rated	2,550	5,000	-20	250	7611-2RS	4768K13	00000
				3/4"	1 3/4"	5/8"	1.922"	0.042"	Sealed	Not Rated	2,550	5,000	-20	250	7612-2RS	4768K6	00000
				13/16"	2"	5/8"	2.156"	0.042"	Sealed	Not Rated	2,950	5,000	-20	250	7613-2RS	4768K14	00000
				7/8"	2"	5/8"	2.156"	0.042"	Sealed	Not Rated	2,950	5,000	-20	250	7614-2RS	4768K15	00000
				15/16"	2"	5/8"	2.156"	0.042"	Sealed	Not Rated	2,950	5,000	-20	250	7615-2RS	4768K16	00000
				1"	2"	5/8"	2.156"	0.042"	Sealed	Not Rated	2,950	5,000	-20	250	7616-2RS	4768K7	00000
				1 1/16"	2 9/16"	3/4"	2.766"	0.065"	Sealed	Not Rated	5,350	5,000	-20	250	7617-2RS	4768K17	00000
				1 1/8"	2 9/16"	3/4"	2.766"	0.065"	Sealed	Not Rated	5,350	5,000	-20	250	7618-2RS	4768K18	00000


				1 1/4"	2 9/16"	3/4"	2.766"	0.065"	Sealed	Not Rated	5,350	5,000	-20	250	7620-2RS	4768K8	00000




						Black-Oxide Steel

						1/2"	1 27/32"	5/8"	2.063"	0.047"	Shielded	1	3,200	9,200	-40	250	ER8	8090T21	00000


						5/8"	1 27/32"	5/8"	2.063"	0.047"	Sealed	Not Rated	2,850	5,000	-20	250	ER10	8090T11	00000
						3/4"	1 27/32"	5/8"	2.063"	0.047"	Sealed	Not Rated	2,850	5,000	-20	250	ER12	8090T12	00000
						7/8"	2 3/64"	3/4"	2.266"	0.047"	Shielded	1	3,450	7,800	-40	250	ER14	8090T22	000000
						15/16"	2 3/64"	3/4"	2.266"	0.047"	Sealed	1	2,800	6,350	-20	220	ER15	8090T27	000000
						1"	2 3/64"	3/4"	2.266"	0.047"	Sealed	Not Rated	3,100	5,000	-20	250	ER16	8090T13	00000
						1 1/16"	2 7/16"	7/8"	2.656"	0.063"	Sealed	1	4,350	5,450	-20	220	ER17	8090T28	000000
						1 1/8"	2 7/16"	7/8"	2.656"	0.063"	Sealed	1	4,850	6,100	-65	250	ER18	8090T57	00000
						1 3/16"	2 7/16"	7/8"	2.656"	0.063"	Sealed	Not Rated	4,350	5,000	-20	250	ER19	8090T14	00000
						1 1/4"	2 27/32"	15/16"	3.078"	0.063"	Sealed	Not Rated	5,750	5,000	-20	250	ER20	8090T15	00000
						1 3/8"	2 27/32"	15/16"	3.078"	0.063"	Shielded	1	6,400	5,000	-40	250	ER22	8090T23	000000


						1 7/16"	2 27/32"	15/16"	3.078"	0.063"	Sealed	Not Rated	5,750	5,000	-20	250	ER23	8090T16	00000
						1 1/2"	3 5/32"	1 3/32"	3.406"	0.063"	Sealed	Not Rated	6,500	5,000	-20	250	ER24	8090T17	000000
						1 5/8"	3 11/32"	1 3/32"	3 19/32"	0.063"	Sealed	1	7,900	3,800	-20	220	ER26	8090T34	000000
						1 11/16"	3 11/32"	1 3/32"	3 19/32"	0.063"	Sealed	1	7,900	3,800	-20	220	ER27	8090T35	000000
						1 3/4"	3 11/32"	1 3/32"	3.578"	0.063"	Shielded	1	8,150	3,900	-40	250	ER28	8090T24	000000
						1 15/16"	3 35/64"	1 1/8"	3.781"	0.094"	Sealed	Not Rated	7,900	5,000	-20	250	ER31	8090T18	000000
						2"	3 15/16"	1 3/16"	4.188"	0.094"	Shielded	1	10,800	3,400	-40	250	ER32	8090T25	000000
						2 3/16"	3 15/16"	1 3/16"	4 3/16"	0.094"	Sealed	1	9,750	3,250	-20	220	ER35	8090T39	000000
						2 1/4"	4 21/64"	1 1/4"	4 37/64"	0.094"	Sealed	1	11,750	3,000	-20	220	ER36	8090T41	000000
						2 3/8"	4 21/64"	1 1/4"	4 37/64"	0.094"	Sealed	1	11,750	3,000	-20	220	ER38	8090T42	000000


						2 7/16"	4 21/64"	1 1/4"	4 37/64"	0.094"	Sealed	1	11,750	3,000	-20	220	ER39	8090T43	000000
						2 1/2"	4 59/64"	1 3/8"	5 9/32"	0.109"	Sealed	1	13,950	2,500	-20	220	ER40	8090T44	000000
						3"	5 33/64"	1 11/16"	5 13/16"	0.109"	Sealed	1	17,400	2,250	-20	220	ER48	8090T48	000000
						20 mm	47 mm	15.9 mm	52.4 mm	1.2 mm	Sealed	1	2,600	7,300	-20	220	ER204	5629N11	000000
						25 mm	52 mm	19.1 mm	57.5 mm	1.2 mm	Sealed	1	2,800	6,350	-20	220	ER205	5629N12	000000
						30 mm	62 mm	22.2 mm	67.5 mm	1.6 mm	Sealed	1	4,350	5,450	-20	220	ER206	5629N13	000000
35 mm						72 mm	23.8 mm	78.2 mm	1.6 mm	Sealed	1	5,750	4,650	-20	220	ER207	5629N14	000000
40 mm	80 mm					27.8 mm	86.5 mm	1.6 mm	Sealed	1	7,300	4,150	-20	220	ER208	5629N15	000000
50 mm	90 mm					28.6 mm	96 mm	2.4 mm	Sealed	1	7,850	3,550	-20	220	ER210	5629N17	000000
70 mm	125 mm					34.9 mm	134.1 mm	2.8 mm	Sealed	1	13,950	2,500	-20	220	ER214	5629N21	000000


Clamp-On Shaft Mount







						Black-Oxide Steel

						3/4"	1 27/32"	5/8"	2.063"	0.047"	Sealed	1	2,600	10,200	-20	220	ER12	6821N11	00000


						1"	2 1/16"	3/4"	2.266"	0.047"	Sealed	1	2,800	9,000	-20	220	ER16	6821N12	00000
						1 1/4"	2 7/16"	7/8"	2.656"	0.063"	Sealed	1	4,350	7,600	-20	220	ER20	6821N15	000000
						1 1/4"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	6,500	-20	220	ER20	6821N16	000000
						1 7/16"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	6,500	-20	220	ER23	6821N18	000000
						1 1/2"	3 5/32"	1 3/32"	3.406"	0.063"	Sealed	1	7,300	5,850	-20	220	ER24	6821N19	000000
						2"	3 15/16"	1 3/16"	4.188"	0.094"	Sealed	1	9,750	4,500	-20	220	ER32	6821N25	000000
						20 mm	47 mm	16 mm	52 mm	1.2 mm	Shielded	1	2,600	6,450	-20	220	ER204	6821N51	000000
						25 mm	52 mm	19 mm	58 mm	1.2 mm	Shielded	1	2,800	6,350	-20	220	ER205	6821N52	000000
						30 mm	62 mm	22 mm	68 mm	1.6 mm	Shielded	1	4,350	5,450	-20	220	ER206	6821N53	000000
				40 mm		80 mm	28 mm	88 mm	1.6 mm	Shielded	1	7,300	4,150	-20	220	ER208	6821N55	000000


				45 mm	85 mm	28 mm	91 mm	1.6 mm	Shielded	1	7,900	3,800	-20	220	ER209	6821N56	000000

Ball Bearings with Retaining Ring

No need for complicated tools—install these bearings by hand inside a housing. The ring stops the bearing from being jostled out of place when it experiences sudden forces parallel to the shaft (thrust loads).

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.

				Retaining Ring					Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	OD	Thk.	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Shielded







				Steel

				10 mm	30 mm	9 mm	34.7 mm	1.12 mm	1	1,200	28,000	-20	230	Standard	6200-2Z	6661K31	000000


				12 mm	32 mm	10 mm	36.7 mm	1.12 mm	1	1,600	26,000	-20	230	Standard	6201-2Z	6661K32	00000
				15 mm	32 mm	9 mm	36.7 mm	1.12 mm	1	1,250	26,000	-20	230	Standard	6002-2Z	6661K33	00000
				15 mm	35 mm	11 mm	39.7 mm	1.12 mm	1	1,800	22,000	-20	230	Standard	6202-2Z	6661K34	00000
				17 mm	40 mm	12 mm	44.6 mm	1.12 mm	1	2,200	19,000	-20	230	Standard	6203-2Z	6661K35	00000
				20 mm	47 mm	14 mm	52.7 mm	1.12 mm	1	3,000	17,000	-20	230	Standard	6204-2Z	6661K36	00000
				20 mm	52 mm	15 mm	57.9 mm	1.12 mm	1	3,750	15,000	-20	230	Standard	6304-2Z	6661K37	00000
				25 mm	52 mm	15 mm	57.8 mm	1.12 mm	1	3,300	14,000	-20	230	Standard	6205-2Z	6661K38	00000
				25 mm	62 mm	17 mm	67.7 mm	1.7 mm	1	5,250	13,000	-20	230	Standard	6305-2Z	6661K39	00000
				30 mm	62 mm	16 mm	67.7 mm	1.7 mm	1	4,550	12,000	-20	230	Standard	6206-2Z	6661K77	00000
				30 mm	72 mm	19 mm	78.6 mm	1.7 mm	1	6,650	11,000	-20	230	Standard	6306-2Z	6661K78	00000


				Sealed







								Steel

								1/2"	1 3/4"	5/8"	1.922"	0.042"	Not Rated	2,550	5,000	-20	250	Extended	7508-2RS	2782T81	00000


								5/8"	1 3/4"	5/8"	1.922"	0.042"	Not Rated	2,550	5,000	-20	250	Extended	7510-2RS	2782T83	00000
								3/4"	1 3/4"	5/8"	1.922"	0.042"	Not Rated	2,550	5,000	-20	250	Extended	7512-2RS	2782T85	00000
								1"	2"	5/8"	2.156"	0.042"	Not Rated	2,950	5,000	-20	250	Extended	7516-2RS	2782T87	00000
								1 1/4"	2 9/16"	3/4"	2.766"	0.065"	Not Rated	5,350	5,000	-20	250	Extended	7520-2RS	2782T89	00000
								10 mm	30 mm	9 mm	34.7 mm	1.12 mm	1	1,200	17,000	-40	210	Standard	6200-2RS	6661K21	00000
								12 mm	32 mm	10 mm	36.7 mm	1.12 mm	1	1,600	15,000	-40	210	Standard	6201-2RS	6661K22	00000
								15 mm	32 mm	9 mm	36.7 mm	1.12 mm	1	1,250	14,000	-40	210	Standard	6002-2RS	6661K23	00000
								15 mm	35 mm	11 mm	39.7 mm	1.12 mm	1	1,800	13,000	-40	210	Standard	6202-2RS	6661K24	00000
								17 mm	35 mm	10 mm	39.7 mm	1.12 mm	1	1,400	13,000	-40	210	Standard	6003-2RS	6661K54	00000
								17 mm	40 mm	12 mm	44.6 mm	1.12 mm	1	2,200	12,000	-40	210	Standard	6203-2RS	6661K25	00000


								17 mm	47 mm	14 mm	52.7 mm	1.12 mm	1	3,200	11,000	-40	210	Standard	6303-2RS	6661K55	00000
								20 mm	47 mm	14 mm	52.7 mm	1.12 mm	1	3,000	10,000	-40	210	Standard	6204-2RS	6661K26	00000
								20 mm	52 mm	15 mm	57.9 mm	1.12 mm	1	3,750	9,500	-40	210	Standard	6304-2RS	6661K27	00000
								25 mm	52 mm	15 mm	57.9 mm	1.12 mm	1	3,300	8,500	-40	210	Standard	6205-2RS	6661K28	00000
								25 mm	62 mm	17 mm	67.7 mm	1.7 mm	1	5,250	7,500	-40	210	Standard	6305-2RS	6661K29	00000
								30 mm	55 mm	13 mm	60.7 mm	1.12 mm	1	3,100	8,000	-40	210	Standard	6006-2RS	6661K56	00000
								30 mm	62 mm	16 mm	67.7 mm	1.7 mm	1	4,550	7,500	-40	210	Standard	6206-2RS	6661K57	00000
								30 mm	72 mm	19 mm	78.6 mm	1.7 mm	1	6,650	6,300	-40	210	Standard	6306-2RS	6661K58	00000

Quick-Mount Ball Bearings for Food and Beverage

You don't need any special tools to install these bearings in food production areas. Slip them onto a shaft and secure with the turn of a screw for easy mounting. Greased with NSF-registered H1 lubricant, these bearings are safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. They're IP69K rated, so they'll stand up to the hot water from a pressure washer when cleaning your facility at the end of the day.

Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.

Corrosion-Resistant Nickel-Plated Steel—These bearings resist mild chemicals, such as the ammonia in cleaning solutions, while maintaining the strength of steel. The nickel coating can wear or chip over time, though. If it does, the steel beneath will rust quickly.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

				Retaining Ring						Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	OD	Thk.	Bearing Seal Type	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Enclosure Rating	Food Industry Std.		Each
Set-Screw Shaft Mount







				Corrosion-Resistant Nickel-Plated Steel

				1"	2 3/64"	3/4"	2.266"	0.047"	Sealed	1	2,800	2,700	-20	220	IP69K	NSF Registered H1	8486N11	0000000


				1 1/4"	2 7/16"	7/8"	2.656"	0.063"	Sealed	1	4,350	2,000	-20	220	IP69K	NSF Registered H1	8486N14	000000
				1 3/8"	2 55/64"	15/16"	3.078"	0.063"	Sealed	1	5,750	2,000	-20	220	IP69K	NSF Registered H1	8486N16	000000
				1 7/16"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	2,000	-20	220	IP69K	NSF Registered H1	8486N17	000000
				1 1/2"	3 5/32"	1 3/32"	3.406"	0.063"	Sealed	1	7,300	1,750	-20	220	IP69K	NSF Registered H1	8486N18	000000
				1 3/4"	3 11/32"	1 3/32"	3.594"	0.063"	Sealed	1	7,900	1,600	-20	220	IP69K	NSF Registered H1	8486N19	000000
				2"	3 15/16"	1 3/16"	4.188"	0.094"	Sealed	1	9,750	1,350	-20	220	IP69K	NSF Registered H1	8486N22	000000
				2 3/16"	3 15/16"	1 3/16"	4.188"	0.094"	Sealed	1	9,750	1,350	-20	220	IP69K	NSF Registered H1	8486N23	00000000


				Clamp-On Shaft Mount







								Corrosion-Resistant Nickel-Plated Steel

								3/4"	1 27/32"	5/8"	2.063"	0.047"	Sealed	1	2,600	3,100	-20	220	IP69K	NSF Registered H1	7177N11	000000


								1"	2 3/64"	3/4"	2.266"	0.047"	Sealed	1	2,800	2,700	-20	220	IP69K	NSF Registered H1	7177N12	000000
								1 3/16"	2 7/16"	7/8"	2.656"	0.063"	Sealed	1	4,350	2,300	-20	220	IP69K	NSF Registered H1	7177N14	000000
								1 1/4"	2 27/32"	15/16"	3.078"	0.063"	Sealed	1	5,750	2,000	-20	220	IP69K	NSF Registered H1	7177N16	000000
								25 mm	52 mm	19.1 mm	57.5 mm	1.2 mm	Sealed	1	2,800	2,700	-20	220	IP69K	NSF Registered H1	7177N26	000000
								35 mm	72 mm	23.8 mm	78.2 mm	1.6 mm	Sealed	1	5,750	2,000	-20	220	IP69K	NSF Registered H1	7177N28	000000
								40 mm	80 mm	27.8 mm	86.5 mm	1.6 mm	Sealed	1	7,300	1,750	-20	220	IP69K	NSF Registered H1	7177N29	000000