17mm Housing ID Bearings

Install and forget these self-lubricating bearings. Their lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Corrosion-Resistant 440C Stainless Steel—Combine the strength of steel with the corrosion resistance of stainless steel. These bearings won't degrade from water or mild chemicals, such as the ammonia in cleaning solutions. However, they'll weaken when exposed to salt water and harsh chemicals, such as bleach.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Corrosion-Resistant 440C Stainless Steel

				6	17	6	1	340	26,000	-10	200	Standard	606	00000000	000000


				7	17	5	1	300	28,000	-10	200	Standard	697	00000000	00000
				9	17	4	1	220	23,000	-10	200	Standard	689	00000000	00000


				Sealed







								Corrosion-Resistant 440C Stainless Steel

								6	17	6	1	340	26,000	-10	200	Standard	606-2RS	00000000	00000


								7	17	5	1	300	28,000	-10	200	Standard	697-2RS	00000000	00000
								9	17	5	1	220	23,000	-10	200	Standard	689-2RS	00000000	00000

Ball Bearings

Open

Shielded

Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Highly-Corrosion-Resistant 316 Stainless Steel—The most corrosion-resistant metal bearings we offer. They won't pit or weaken from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Highly-Corrosion-Resistant 316 Stainless Steel

				6	17	6	Not Rated	75	2,300	-40	140	Standard	606	0000000	000000


				Shielded







								Corrosion-Resistant 440C Stainless Steel

								9	17	5	5	290	43,000	-40	240	Standard	689-2Z	00000000	00000

Flanged Ball Bearings

Open

Shielded

Install these bearings inside a housing and they won't budge. The flange presses against the housing wall, so vibration and other sudden forces parallel to the shaft (thrust loads) won't knock them off-kilter.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

				Flange, mm					Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	OD	Thk.	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Open







				Steel

				6	17	6	19	1.2	3	500	49,000	-50	300	Standard	606	000000000	000000




						Corrosion-Resistant 440C Stainless Steel

						6	17	6	19	1.2	3	400	49,000	-50	300	Standard	606	000000000	00000


						9	17	4	19	1	3	230	44,000	-50	300	Standard	689	000000000	00000


						Shielded







										Steel

										6	17	6	19	1.2	3	500	42,000	-50	300	Standard	606-2Z	000000000	00000




												Corrosion-Resistant 440C Stainless Steel

												6	17	6	19	1.2	3	400	42,000	-50	300	Standard	606-2Z	000000000	00000


												9	17	5	19	1.1	3	230	37,000	-50	300	Standard	689-2Z	000000000	00000
												9	17	5	19	1.1	5	290	43,000	-20	250	Standard	689-2Z	00000000	00000

Ball Bearings for Food and Beverage

Sealed

Food production rolls along smoothly on these bearings. Greased with FDA-compliant lubricant, they’re safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. The lubricant is a solid material that fills the space between the balls and releases oil over time, so you'll never need to add more.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Food Industry Std.	Bearing Trade No.		Each
Sealed







				Corrosion-Resistant 440C Stainless Steel

				6	17	6	1	500	26,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	606-2RS	00000000	000000


				9	17	5	1	290	23,000	-40	200	Standard	FDA Compliant 21 CFR 178.3570	689-2RS	00000000	00000

Dry-Running Ball Bearings

Made of naturally slippery plastic so there's no lubricant to maintain or make a mess. These bearings are ideal for spic-and-span spaces since oil won't drip off, wash out, or collect dust over time. They won't rust or warp from moisture, so they stand up to thorough cleanings.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, reducing wear and extending the life of the bearing.

Acetal—The most common choice for plastic bearings, acetal is economical yet still stands up to daily wear and tear.

316 Stainless Steel Balls—Won't corrode from salt water or harsh chemicals, such as bleach and chlorine found in cleaning solutions.

						Temp. Range, ° F				316 Stainless Steel Balls
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	ABEC Rating	Bearing Trade No.		Each
Open







				Acetal

				6	17	6	25	2,300	-40	180	Not Rated	606	00000000	00000

High-Precision Ball Bearings

Open

Shielded

The most precise bearings we offer, with tolerances tighter than a speck of dust. Rated ABEC 7 out of 9, they meet strict tolerance standards established by the Annular Bearing Engineers Committee (ABEC). You'll find them in equipment that requires both high speed and pinpoint accuracy, such as gyroscopes.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type		Each
Open







				Corrosion-Resistant 440C Stainless Steel

				9	17	4	7	235	31,000	-30	280	Standard	0000000	000000


				Shielded







								Corrosion-Resistant 440C Stainless Steel

								9	17	6	7	235	31,000	-30	280	Standard	0000000	00000

Precision Needle-Roller Bearings


	Bearing

Install these bearings directly onto hardened and ground shafts. They have higher load capacity, speed, and accuracy than standard needle-roller bearings.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

Shaft Liners—Shaft liners allow you to use the bearing on unhardened and unground shafts.

	Roller Bearings											Shaft Liners
				Radial Load Cap., lb.
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	For Shaft Surface Smoothness, Ra, μin	Temp. Range, ° F		Each	For Shaft Dia., mm		Each
For Radial Load—Open with Steel Ring



		10	17	12	1,050	1,200	27,000	Required	4	0 to 245	0000000	000000	7	0000000	00000

Dry-Running Flanged Sleeve Bearings

Made of naturally slippery plastic so you’ll never have to add lubricant. They’re ideal for clean environments where you need to prevent oil drips or graphite flakes. Compared to metal bearings, they are lighter and will never rust.

Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

Ultra-Chemical-Resistant PTFE—The most chemical-resistant bearings we offer. PTFE is unaffected by the harsh fluids that other plastics can't handle, including all strong acids and bases. PTFE also reduces friction better than nylon but is not as strong.

High-Load PEEK—Get the strength of reinforced PTFE without compromising on heat resistance. With no additives, such as polyester fabric, PEEK bearings won’t melt at high temperatures. They’re also nearly as slippery and chemical resistant as plain PTFE.

High-Load Moisture-Resistant Rulon LR—Won’t swell in wet or humid places, similar to acetal, but can support higher loads. These bearings also operate smoothly from cryogenic to oven-like temperatures.

Moisture-Resistant Ultra-Low-Friction Plastic Blend—These bearings won't warp or swell from humidity or direct contact with water. They glide effortlessly for applications with frequent starts and stops, such as conveyor systems.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Color	Temp. Range, ° F	Specs. Met		Each
Ultra-Chemical-Resistant PTFE



	12	17	12	22	2.5	15 lb. @ 120 rpm	15 lb. @ 120 rpm	White	-200 to 450	FDA Compliant 21 CFR 177.1550	00000000	000000


	High-Load PEEK



			12	17	20	22	2.5	350 lb. @ 120 rpm	210 lb. @ 120 rpm	Beige	-20 to 450	—	00000000	00000


			High-Load Moisture-Resistant Rulon LR



					12	17	16	22	2.5	200 lb. @ 120 rpm	150 lb. @ 120 rpm	Maroon	-400 to 500	—	00000000	00000


					Moisture-Resistant Ultra-Low-Friction Plastic Blend



							15	17	9	23	1	215 lb. @ 60 rpm	250 lb. @ 60 rpm	Yellow	-50 to 190	—	00000000	0000


							15	17	12	23	1	290 lb. @ 60 rpm	250 lb. @ 60 rpm	Yellow	-50 to 190	—	00000000	0000
							15	17	17	23	1	410 lb. @ 60 rpm	250 lb. @ 60 rpm	Yellow	-50 to 190	—	00000000	0000

Oil-Embedded Flanged Sleeve Bearings

Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

High-Load 863 Iron Copper—Iron makes these bearings harder, stronger, and more resistant to sudden starts and stops than 841 bearing bronze. However, they operate at slower speeds. The increased iron content makes these bearings appear silver.

Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	12	17	12	22	2.5	440 lb. @ 120 rpm	760 lb. @ 120 rpm	Synthetic Oil	-35 to 300	0000000	00000


	12	17	16	22	2.5	590 lb. @ 120 rpm	760 lb. @ 120 rpm	Synthetic Oil	-35 to 300	0000000	0000
	12	17	20	22	2.5	740 lb. @ 120 rpm	760 lb. @ 120 rpm	Synthetic Oil	-35 to 300	0000000	0000


	High-Load 863 Iron Copper



			12	17	12	22	2.5	520 lb. @ 120 rpm	530 lb. @ 120 rpm	Synthetic Oil	-15 to 300	0000000	0000


			12	17	16	22	2.5	700 lb. @ 120 rpm	530 lb. @ 120 rpm	Synthetic Oil	-15 to 300	00000000	0000
			12	17	20	22	2.5	870 lb. @ 120 rpm	530 lb. @ 120 rpm	Synthetic Oil	-15 to 300	00000000	0000

Dry-Running Flanged Sleeve Bearings for Food and Beverage

Made of plastics permitted by the US FDA for contact with food, these bearings won’t release harmful, smelly, and distasteful impurities into your food or beverage production line. These self-lubricating plastics eliminate the need for oil, resulting in less maintenance and improved hygiene. You’ll find them inside food-processing equipment such as mixers, conveyors, and fillers.

Moisture-Resistant Plastic Blend—Similar to UHMW, these bearings will keep their shape after washdowns but won’t hold up to steam cleaning. They're bright blue so they are easy to spot if they fall into your production line.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Color	Temp. Range, ° F	Specs. Met		Each
Moisture-Resistant Plastic Blend



	15	17	9	23	1	30 lb. @ 60 rpm	50 lb. @ 60 rpm	Blue	-50 to 190	FDA Compliant 21 CFR 177.1520, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 178.3297	000000000	00000


	15	17	12	23	1	40 lb. @ 60 rpm	50 lb. @ 60 rpm	Blue	-50 to 190	FDA Compliant 21 CFR 177.1520, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 178.3297	000000000	0000
	15	17	17	23	1	55 lb. @ 60 rpm	50 lb. @ 60 rpm	Blue	-50 to 190	FDA Compliant 21 CFR 177.1520, FDA Compliant 21 CFR 177.1550, FDA Compliant 21 CFR 178.3297	000000000	0000

Dry-Running Sleeve Bearings for Food and Beverage

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

	For Housing ID, mm	Lg., mm	Dynamic Radial Load Cap. @ Speed	Color	Temp. Range, ° F	Specs. Met		Each
Moisture-Resistant Plastic Blend



	15	17	15	320 lb. @ 60 rpm	Blue	-50 to 190	FDA Compliant 21 CFR 177.1550	00000000	00000


	15	17	25	540 lb. @ 60 rpm	Blue	-50 to 190	FDA Compliant 21 CFR 177.1550	00000000	0000

Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings

Our slipperiest metal bearings, these are ideal for machinery with frequent starts and stops, such as conveyors. With nonstick PTFE particles added to the oil, they reduce friction to minimize wear and heat, so equipment runs more efficiently and lasts longer. All are fabricated, lubricated, and inspected in the U.S.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Base Oil	Lubricant Additive	Temp. Range, ° F	Specs. Met		Each
841 Bearing Bronze



	12	17	16	22	2.5	590 lb. @ 120 rpm	760 lb. @ 120 rpm	Synthetic Oil	PTFE	-60 to 300	ASTM B438	00000000	000000


	12	17	20	22	2.5	740 lb. @ 120 rpm	760 lb. @ 120 rpm	Synthetic Oil	PTFE	-60 to 300	ASTM B438	00000000	00000


	High-Load 863 Iron Copper



			12	17	12	22	2.5	520 lb. @ 120 rpm	530 lb. @ 120 rpm	Synthetic Oil	PTFE	-60 to 300	—	00000000	0000


			12	17	16	22	2.5	700 lb. @ 120 rpm	530 lb. @ 120 rpm	Synthetic Oil	PTFE	-60 to 300	—	00000000	00000
			12	17	20	22	2.5	870 lb. @ 120 rpm	530 lb. @ 120 rpm	Synthetic Oil	PTFE	-60 to 300	—	00000000	00000

Flanged Sleeve Bearings

These bearings don’t come with a lubricant, so you can select the oil that meets the needs of your application. You’ll need to refill the oil, so make sure the bearing is located where you can access it. All are fabricated and inspected in the U.S.

High-Load 932 Bearing Bronze—These bearings are strong enough for sudden starts and stops, plus they resist wear and tear. They are cast from an alloy of leaded tin bronze for uniform rigidity and strength. Also known as 660 leaded bronze bearings.

	For Housing ID, mm	Lg., mm	Flange OD, mm	Flange Thk., mm	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Temp. Range, ° F		Each
High-Load 932 Bearing Bronze



	12	17	12	22	2.5	890 lb. @ 120 rpm	1,100 lb. @ 120 rpm	-350 to 450	00000000	000000


	12	17	16	22	2.5	1,150 lb. @ 120 rpm	1,100 lb. @ 120 rpm	-350 to 450	00000000	00000