McMaster-Carr logo
    Filter by
    System of Measurement
    Shaft Diameter
    Attribute Image
    Ball Bearing Profile
    Bearing Seal Type
    For Housing ID
    Attribute Image
    Shaft Type
    Bearing Type
    Industrial Info Compare
    Cage Material
    Dynamic Radial Load Capacity
    Bearing Construction
    Inner Ring Type
    Shaft Width
    Number of Set Screws Included
    DFARS Specialty Metals
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    7 Products

    Quick-Mount Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Quick-Mount Ball Bearings, Set-Screw Shaft Mount.

    Set-Screw

    Shaft Mount

    Slip onto a shaft and secure with the turn of a screw. You don't need any special tools to mount these bearings.
    Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.
    Black-Oxide Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.
    Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Retaining
    Ring
    Temp.
    Range, ° F
    For Shaft
    Dia.
    For Housing
    ID
    Wd.
    OD
    Thk.
    Bearing Seal
    Type
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Bearing
    Trade No.
    Each
    Set-Screw Shaft Mount
     
    Black-Oxide Steel
    7/8"2 3/64"3/4"2.266"0.047"Shielded13,4507,800-40250ER14
    		00000000000000
    15/16"2 3/64"3/4"2.266"0.047"Sealed12,8006,350-20220ER15
    		0000000000000
    1"2 3/64"3/4"2.266"0.047"SealedNot Rated3,1005,000-20250ER16
    		000000000000
     

    Tapered-Roller Bearings

    Image of Product. Front orientation. Roller Bearings. Tapered-Roller Bearings.
    Image of Attribute. Side1 orientation. Contains Annotated. Tapered-Roller Bearings.
    Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
    Radial Load
    Cap., lb.
    Thrust Load
    Cap., lb.
    For Shaft
    Dia.
    For Housing
    ID
    Wd.
    Bearing Trade
    No.
    Dynamic
    Static
    Dynamic
    Static
    Max. Rotation
    Speed, rpm
    Lubrication
    Temp. Range,
    ° F
    Each
    For Combined Radial and Thrust Load—Open with Steel Ring
    7/8"2 3/64"1/2"07087/072041,7006,6501,1507,7504,100Required-60 to 20000000000000000
     

    Quick-Mount Ball Bearings for Food and Beverage

    Image of Product. Front orientation. Ball Bearings. Quick-Mount Ball Bearings for Food and Beverage, Set-Screw Shaft Mount.

    Set-Screw Shaft

    Mount

    Image of Product. Front orientation. Ball Bearings. Quick-Mount Ball Bearings for Food and Beverage, Clamp-On Shaft Mount.

    Clamp-On Shaft

    Mount

    You don't need any special tools to install these bearings in food production areas. Slip them onto a shaft and secure with the turn of a screw for easy mounting. Greased with NSF-registered H1 lubricant, these bearings are safe to install on food-processing equipment, such as conveyor belts, so long as they don’t directly touch the food. They're IP69K rated, so they'll stand up to the hot water from a pressure washer when cleaning your facility at the end of the day.
    Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.
    Clamp-On Shaft Mount—The clamp tightens around the shaft for a strong 360° grip. These mounts attach more securely than set screws to reduce vibration. Plus, there aren't any screws pressing into the shaft, so it stays free from damage. Also known as a concentric lock.
    Corrosion-Resistant Nickel-Plated Steel—These bearings resist mild chemicals, such as the ammonia in cleaning solutions, while maintaining the strength of steel. The nickel coating can wear or chip over time, though. If it does, the steel beneath will rust quickly.
    Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Retaining
    Ring
    Temp.
    Range, ° F
    For Shaft
    Dia.
    For Housing
    ID
    Wd.
    OD
    Thk.
    Bearing
    Seal Type
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Enclosure
    Rating
    Food Industry
    Std.
    Each
    Set-Screw Shaft Mount
     
    Corrosion-Resistant Nickel-Plated Steel
    1"2 3/64"3/4"2.266"0.047"Sealed12,8002,700-20220IP69K
    		NSF Registered H1
    		00000000000000
     
    Clamp-On Shaft Mount
     
    Corrosion-Resistant Nickel-Plated Steel
    1"2 3/64"3/4"2.266"0.047"Sealed12,8002,700-20220IP69K
    		NSF Registered H1
    		0000000000000
     

    Hex-Bore Ball Bearings

    Image of Product. Front orientation. Ball Bearings. Hex-Bore Ball Bearings.
    No need for set screws—the inside corners of these bearings hold them in place on hex shafts as they rotate. They're a good choice when your setup needs to come apart frequently, since there aren't extra mounting steps.
    Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.
    Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.
    Extended Inner Ring—Connect to mating parts without the need for a spacer. The inner ring juts out farther than the outer ring, so shaft collars and other objects won't touch the bearing's moving parts.
    ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.
    Temp.
    Range, ° F
    For Shaft
    Wd.
    For Housing
    ID
    Wd.
    ABEC
    Rating
    Dynamic Radial
    Load Cap., lb.
    Max. Rotation
    Speed, rpm
    Min.
    Max.
    Inner Ring
    Type
    Bearing Trade
    No.
    Each
    Sealed
     
    Steel
    7/8"2 3/64"19/32"13,1505,900-40250ExtendedHPC014GP000000000000
     
    back to top