About Plain Bearings
More
About Ball and Roller Bearings
More
Set Screw Collar Ball Bearings
Slip these bearings onto a shaft and secure with the included set screws, no special tools required. All have an extended inner ring for additional shaft support.
Bearings with a black-oxide steel ring have some corrosion resistance.
Sealed bearings block out dust and other contaminants better than shielded bearings.
Bearings with a retaining ring have a removable retaining ring that holds the bearing inside a housing.
For technical drawings and 3-D models, click on a part number.
Inner Ring | Retaining Ring | Radial Load Cap., lbs. | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Bearing Trade Number  | For Shaft Dia. | For Housing ID | Wd. | OD | Wd. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | ABEC Rating | Each | |
Sealed (Lubricated) | ||||||||||||||
Steel—With Retaining Ring | ||||||||||||||
| 7617-2RS | 1 1/16" | 2 9/16" | 3/4" | 1.672" | 1.417" | 2.766" | 0.065" | 5,350 | 2,600 | 5,000 | -20° to 250° | Not Rated | 0000000 | 000000 |
Black-Oxide Steel—With Retaining Ring | ||||||||||||||
| ER17 | 1 1/16" | 2.441" | 7/8" | 1.5938" | 1.5" | 2 21/32" | 0.0625" | 4,350 | 2,550 | 5,450 | -20° to 220° | ABEC-1 | 0000000 | 000000 |
One-Piece Thrust Ball Bearings
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
| 1 1/16" | 1 31/32" | 5/8" | Steel | 6,700 | 13,100 | 3,800 | Required | -40° to 245° | Lubrication Hole | 00000000 | 000000 |
Oil-Embedded Thrust Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
Ultra-Low-Friction Oil-Embedded Thrust Bearings
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
For technical drawings and 3-D models, click on a part number.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Specifications Met | Each | |
For 1 1/16" Shaft Dia. | ||||||||
|---|---|---|---|---|---|---|---|---|
| 2 3/8" | 1/16" | 7,050 lbs. @ 30 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | ASTM B438 | 00000000 | 000000 |
| 2 3/8" | 1/8" | 7,050 lbs. @ 30 rpm | Lubricated | SAE 20 Oil with PTFE | -60° to 300° | ASTM B438 | 00000000 | 00000 |
Tapered-Roller Bearings
Found anywhere from machine tool spindles to conveyor rollers, these bearings have a two-piece design that allows for adjustment.
Zinc-plated steel bearings provide better corrosion resistance than steel bearings.
For technical drawings and 3-D models, click on a part number.
Radial Load Cap., lbs. | Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | For Housing ID | Wd. | Bearing Trade Number | Dynamic | Static | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Each | |
Steel Ring | ||||||||||||
Open | ||||||||||||
| 1 1/16" | 1 63/64" | 0.42" | L44649/L44610 | 1,600 | 7,400 | 1,000 | 8,050 | 3,900 | Required | -60° to 200° | 0000000 | 000000 |
Zinc-Plated Steel Ring | ||||||||||||
Open | ||||||||||||
| 1 1/16" | 1 63/64" | 0.42" | L44649/L44610 | 1,600 | 7,400 | 1,000 | 8,050 | 3,900 | Required | -60° to 200° | 0000000 | 00000 |
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
For technical drawings and 3-D models, click on a part number.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Each | |
Steel Rollers | ||||||||||
Open | ||||||||||
| 1 1/16" | 1 5/8" | 5/64" | 3,400 | 13,700 | 8,400 | Required | 0.2 | 0° to 240° | 00000000 | 00000 |
Compact-Base Mounted Ball Bearings
Also known as tapped-base bearings, these ball bearings mount to surfaces from the bottom through threaded holes. Because of their narrow profile, they’re commonly used in tight-clearance spaces, including systems where multiple shafts are mounted close together.
Set screw shaft-mount bearings secure to shafts when you tighten the set screw, with no need for an additional collar. Set screws cause some amount of marring on shafts.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting Hole | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Center Ht. | Ht. | Lg. | Wd. | Thread Size | Dp. | Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 1 1/16" | 1 11/16" | 3 13/32" | 4" | 1 1/2" | 7/16"-14 | 0.625" | 3" | 4,380 | 2,560 | 5,450 | -20° to 220° | Self Aligning | Lubricated | 00000000 | 0000000 |
Ultra-Corrosion-Resistant Mounted Ball Bearings with Two-Bolt Flange
Use these bearings in corrosive environments and under water. All are self-aligning to compensate for shaft misalignment.
316 stainless steel bearings handle heavier loads than acetal bearings.
For technical drawings and 3-D models, click on a part number.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, °F | Max. Temp. Rating in Liquid, °F | Alignment Style | Lubrication | Each | |
Open 316 Stainless Steel Bearings with Polyester Plastic Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 1 1/16" | 3 9/64" | 5 53/64" | 1 5/8" | 9/16" | 7/16" | 4 39/64" | 380 | 280 | 690 | -30° to 180° | 120° | Self Aligning | Not Required | 0000000 | 0000000 |
Press-Fit Drill Bushings
Also known as jig bushings, these drill bushings fit inside fixture plate holes to precisely guide drill bits, counterbores, reamers, and other cutting tools. They improve accuracy so your drilled holes and cuts are consistent from part to part. Known for their versatility, drill bushings are also used as spacers, shims, and machinery bushings.
Press into place with a manual or hydraulic press. Since these bushings are sized slightly larger than the hole for an extremely tight fit, they’ll stay put permanently. These are ANSI Type P bushings—also known as headless bushings—which means you don’t need to counterbore the hole to mount them flush.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Tolerance | Each | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
1.0625" ID | ||||||||||||
| 1 1/2" | 3/4" | 1 1/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 000000 | 000000 | 000000 |
| 1 1/2" | 1" | 1 1/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 1/2" | 1 3/4" | 1 1/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 1/2" | 2" | 1 1/16" | 0.0002" to 0.0006" | 0.0018" to 0.0022" | -0.01" to 0.01" | P | Steel | Rockwell C61 | 000000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1" | 1 1/16" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/8" | 1 1/16" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 1/2" | 1 1/16" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/4" | 1 1/16" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | P | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Press-Fit Drill Bushings with Head
A flanged head on these bushings acts as a stop, so they won’t press through your jig even under extreme drilling pressure. They’re ANSI Type H bushings, also known as headed bushings. The head adds support and protects the jig from damage caused by heavy use, so they’re often used in jigs made of thin or soft materials. These bushings guide your drill bit, reamer, or other cutting bit to create accurate, consistent holes from one workpiece to the next. They’re also used as spacers, shims, and machinery bushings. Made of hardened, ground steel, they hold their shape and resist wear, so they last for many cycles without needing to be replaced.
To install, fit the bushing into a hole in your jig. In a standard hole, the head will sit above the jig plate; to mount flush, install in a countersunk hole. A chamfered edge on the bottom of the bushing helps center the bushing in the hole. Once it’s centered, press the bushing into place with a hydraulic or lever press.
Don't see the size you need? Additional sizes are available.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | ID | OD | Lg. | Drill Bushing Type | Material | Hardness | 1-5 | 6-11 | 12-Up | |
1.0625" ID | ||||||||||||||
| 1 3/4" | 3/4" | 1 1/16" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 000000 | 000000 | 000000 |
| 1 3/4" | 1" | 1 1/16" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/8" | 1 1/16" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 2 1/8" | 1 1/16" | 1 63/64" | 3/8" | 0.0002" to 0.0006" | 0.0019" to 0.0023" | -0.015" to 0.015" | H | Steel | Rockwell C61 | 00000000 | 00000 | 00000 | 00000 |
Removable Drill Bushings
Replace worn bushings and quickly change IDs without needing to repeatedly use a lever press. Instead of pressing bushings in and out of your jig fixture, which can cause damage, these bushings slide in and out of sleeves (sold separately). By swapping in a bushing with a different ID, you can change the size of your bit and still use the same hole in your fixture. All are made to tight dimensional tolerances for consistent, accurate results, even as you change them in and out. They're also known as slip-fixed and renewable bushings.
Choose a sleeve with a length that matches the length of your bushing. To prevent bushings from spinning inside the sleeve as you drill, pair a standard sleeve with a lock screw, or use a locking sleeve.
Lock screws thread into a hole in your jig. The head of the screw fits into a notch on the bushing's head, which keeps the bushing from spinning.
For additional sizes, see Made-to-Order Removable Drill Bushings.
For technical drawings and 3-D models, click on a part number.
Head | Tolerance | Each | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| OD | Lg. | For Drill Bit Size | OD | Thick. | Lock Screw/Bushing Ctr.-to-Ctr. | ID | OD | Lg. | Drill Bushing Type | Material | 1-5 | 6-11 | 12-Up | |
1.0625" ID | ||||||||||||||
| 1 3/4" | 3/4" | 1 1/16" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 000000 | 000000 | 000000 |
| 1 3/4" | 1" | 1 1/16" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
| 1 3/4" | 1 3/8" | 1 1/16" | 2 19/64" | 3/8" | 1 25/64" | 0.0002" to 0.0006" | -0.0003" to 0" | -0.015" to 0.015" | SF | Steel | 00000000 | 00000 | 00000 | 00000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
For technical drawings and 3-D models, click on a part number.
Keyway | ||||||||
|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
Clamp On | ||||||||
JA Style Bushing | ||||||||
| 1 1/16" | 1" | 1/4" | 1/16" | 60 | Steel | Clamping Screws, Machine Key | 00000000 | 000000 |
SD Style Bushing | ||||||||
| 1 1/16" | 1 13/16" | 1/4" | 1/8" | 108 | Steel | Clamping Screws | 00000000 | 00000 |
SDS Style Bushing | ||||||||
| 1 1/16" | 1 3/8" | 1/4" | 1/8" | 108 | Steel | Clamping Screws | 00000000 | 00000 |
SH Style Bushing | ||||||||
| 1 1/16" | 1 5/16" | 1/4" | 1/8" | 108 | Steel | Clamping Screws | 00000000 | 00000 |
SK Style Bushing | ||||||||
| 1 1/16" | 1 15/16" | 1/4" | 1/8" | 180 | Steel | Clamping Screws | 00000000 | 00000 |