100 mm ID Bearings | McMaster-Carr

For silky-smooth motion, the balls inside these bearings roll nearly friction-free. You'll often find them at the end of a shaft or between a stationary and rotating surface, such as on a propeller or rotary table.

These bearings come as three separate pieces—one cage and two washers. The cage holds the balls in place, while the washers create a surface for the balls to roll on. This design is easy to lubricate, but the oil will attract dust and grime since it's exposed.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	OD, mm	Thk., mm	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F	Includes		Each
Steel



	100	135	25	Steel	19,100	2,400	-40 to 250	Two Washers	00000000	0000000

Thin-Profile Crossed-Roller Bearings

For a more compact machine, these bearings have thinner inner and outer rings than high-load crossed-roller bearings. Route hydraulic lines, electrical wiring, and other components through the inside of the bearing. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Temp. Range, ° F	Features		Each
For Combined Radial, Thrust, and Moment Load—Open with Steel Ring



		100	111	5	750	1,450	750	Required	0 to 175	Lubrication Hole	0000000	0000000


		For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring



				100	116	8	1,600	3,100	350	Lubricated	0 to 175	Lubrication Groove, Lubrication Hole	0000000	000000

Maintenance-Free Turntable Bearings


	Turntable Bearings with Gear Teeth

With low-friction internal sleeves made of PTFE, these bearings never need lubrication. Also known as slewing-ring bearings, they’re used for slow, controlled rotation. You’ll often see them rotating hoists, robotic arms, and other heavy machinery. They have holes on both the inner and outer ring, so they’re easy to align and mount.

Note: Listed capacities only apply when bearings are mounted parallel to the ground. These bearings can be mounted in other orientations, but their capacities will be reduced.

Turntable Bearings with Gear Teeth—Bearings with gear teeth can be driven by a spur gear. For components to mesh correctly, they must have the same pressure angle and module.

	Thrust Load Cap., lb.		Radial Load Cap., lb.									Bearing
	Dynamic	Static	Dynamic	Static	Static Moment Load Cap., ft·lbf	OD, mm	ID, mm	Overall Ht., mm	Gear Module	Pressure Angle	Material	Type	Material	Plain Bearing Type	Mounting Fasteners Included		Each
For Combined Radial, Thrust, and Moment Loads







				Turntable Bearings

				3,550	12,350	1,100	3,550	1,100	185	100	34	—	—	Anodized Aluminum	Plain	PTFE	Sleeve	No	000000	0000000




						Turntable Bearings with Gear Teeth

						3,550	12,350	1,100	3,550	1,100	196	100	36	2	20°	Anodized Aluminum	Plain	PTFE	Sleeve	No	00000000	00000000

Spherical-Roller Bearings

Two rows of rollers give these bearings dynamic radial load capacities over five times higher than comparably sized tapered-roller bearings. Also known as rock crusher bearings, they handle heavy shock loads and are used for metal milling machinery, mining and oil field equipment, and in paper mills.

						Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Bearing Trade No.	Ring Material	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Max. Temp., ° F		Each
Open Bearing



		100	180	46	22220	Steel	102,000	110,000	2,800	Required	390	0000000	0000000

Low-Profile Maintenance-Free Turntable Bearings

At 16 mm tall, these bearings are about the height of your typical plastic water bottle cap, so they won’t bulk up your builds. They handle radial, thrust, and moment loads. Often used to oscillate heavy equipment, find them rotating hoists or spinning components on robotic arms. The internal sleeve moves smoothly and will never require lubrication. For easy alignment and mounting, these bearings have holes on both the inner and outer ring. They’re also known as slewing-ring bearings.

Note: Listed capacities only apply when bearings are mounted parallel to the ground. Otherwise, they reduce when bearings are tilted.

	Thrust Load Cap., lb.		Radial Load Cap., lb.							Bearing
	Dynamic	Static	Dynamic	Static	Static Moment Load Cap., ft·lbf	OD, mm	ID, mm	Overall Ht., mm	Material	Type	Material	Plain Bearing Type	Mounting Fasteners Included		Each
For Combined Radial, Thrust, and Moment Loads



		1,100	4,450	330	330	330	160	100	16	Anodized Aluminum	Plain	PTFE	Sleeve	No	0000000	0000000

High-Load Crossed-Roller Bearings

The thicker inner and outer raceways on these bearings can handle heavier loads than the thin-profile crossed-roller bearings. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Temp. Range, ° F	Features		Each
For Combined Radial, Thrust, and Moment Load—Open with Steel Ring



		100	150	20	11,400	16,200	600	Required	0 to 245	—	0000000	0000000


		For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring



				100	150	20	11,400	16,200	480	Lubricated	0 to 245	Lubrication Groove, Two Lubrication Holes	0000000	000000

Needle-Roller Thrust Bearings


Bearings	Washers

Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.

A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	Thrust Bearings										Thin Washers
	For Shaft Dia., mm	OD, mm	Thk., mm	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F	Specs. Met		Each	Thk., mm		Each
Steel



		100	135	4	Steel	20,400	2,420	0 to 240	DIN 5405-3, ISO 303	00000000	000000	1	00000000	000000

Washers for Needle-Roller Thrust Bearings

Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.

For Shaft Dia., mm	OD, mm	Thk., mm	Washer Material	Specs. Met		Each
100	135	1	Steel	DIN 5405-3, ISO 303	00000000	000000

Static-Control Maintenance-Free Turntable Bearings

Image of Product. Front orientation. Turntable Bearings. Maintenance-Free, Static Control.

Safe enough to rotate equipment in microchip and semiconductor manufacturing, these bearings prevent harmful static buildup. They’re made from stainless steel and have specially formulated PTFE sleeves that work together to drain static. Make sure your set up provides a path to the ground.

Also known as slewing-ring bearings, these bearings are great for turning heavy equipment in a slow and controlled way. Their sleeves are also slippery, so they move smoothly and don't require lubrication. For alignment and mounting, they have holes on both the inner and outer ring.

Note: Listed capacities only apply when bearings are mounted parallel to the ground. These bearings can be mounted in other orientations, but their capacities will be reduced.

	Thrust Load Cap., lb.		Radial Load Cap., lb.							Bearing
	Dynamic	Static	Dynamic	Static	Static Moment Load Cap., ft·lbf	OD, mm	ID, mm	Overall Ht., mm	Material	Type	Material	Plain Bearing Type	Mounting Fasteners Included	Performance		Each
For Combined Radial, Thrust, and Moment Loads



		3,550	12,350	1,100	3,550	1,100	185	100	34	Stainless Steel	Plain	PTFE	Sleeve	No	Antistatic	00000000	000000000