120 mm ID Bearings | McMaster-Carr

Smoother than smooth—the balls inside these bearings roll nearly friction-free. You’ll often find them on rapidly rotating parts, from the whirring chuck on a power drill to the spinning shaft on an electric motor.

Shielded—The balls are covered just enough to keep out large particles while allowing air to pass through and dissipate heat.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

							Temp. Range, ° F
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Inner Ring Type	Bearing Trade No.		Each
Shielded







				Steel

				120	180	28	3	19,850	3,800	-20	230	Standard	6024-2Z	4481N29	0000000


				Sealed







								Steel

								120	180	28	3	19,850	2,800	-30	210	Standard	6024-2RS	4481N76	000000

Thin-Profile Crossed-Roller Bearings

For a more compact machine, these bearings have thinner inner and outer rings than high-load crossed-roller bearings. Route hydraulic lines, electrical wiring, and other components through the inside of the bearing. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Temp. Range, ° F	Features		Each
For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring



		120	136	8	1,750	3,700	275	Lubricated	0 to 175	Lubrication Groove, Lubrication Hole	1378N76	0000000

High-Load Crossed-Roller Bearings

The thicker inner and outer raceways on these bearings can handle heavier loads than the thin-profile crossed-roller bearings. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Temp. Range, ° F	Features		Each
For Combined Radial, Thrust, and Moment Load—Open with Steel Ring



		120	180	25	16,500	24,250	500	Required	0 to 245	—	4489N16	000000000


		For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring



				120	180	25	16,500	24,250	400	Lubricated	0 to 245	Lubrication Groove, Two Lubrication Holes	4489N24	00000000

Thrust Ball Bearings

For silky-smooth motion, the balls inside these bearings roll nearly friction-free. You'll often find them at the end of a shaft or between a stationary and rotating surface, such as on a propeller or rotary table.

These bearings come as three separate pieces—one cage and two washers. The cage holds the balls in place, while the washers create a surface for the balls to roll on. This design is easy to lubricate, but the oil will attract dust and grime since it's exposed.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	OD, mm	Thk., mm	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F	Includes		Each
Steel



	120	155	25	Steel	20,000	2,200	-40 to 250	Two Washers	7806K732	0000000

Needle-Roller Thrust Bearings


Bearings	Washers

Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.

A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	Thrust Bearings										Thin Washers
	For Shaft Dia., mm	OD, mm	Thk., mm	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F	Specs. Met		Each	Thk., mm		Each
Steel



		120	155	4	Steel	22,900	2,070	0 to 240	DIN 5405-3, ISO 303	5909K963	0000000	1	5909K111	000000

Washers for Needle-Roller Thrust Bearings

Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.

For Shaft Dia., mm	OD, mm	Thk., mm	Washer Material	Specs. Met		Each
120	155	1	Steel	DIN 5405-3, ISO 303	5909K111	000000

Bearing Spring Lock Washers for Slotted Bearing Nuts


	For Chamfered Nuts

Designed for use with bearing nuts, these lock washers have a conical shape that presses like a spring against bearings, bushings, gears, and pulleys to hold them in place on your threaded shaft or spindle. They also have an inner tab that sits in the shaft or spindle’s keyway to prevent the nut from loosening.

Steel—Steel washers are strong and flexible.

External Tooth—Washers with external teeth grip components using their teeth, in addition to spring tension.

DIN 5406—DIN 462 and DIN 5406 washers meet international standards for lock washer dimensions. Pair DIN 462 washers with DIN 1804 bearing nuts, and DIN 5406 washers with DIN 981 bearing nuts.

					Tab, mm
	For Screw Size	ID, mm	OD, mm	Thk., mm	Wd.	Dp.	Overall Ht., mm	Tooth Location	Hardness	Specs. Met	For Bearing Nut Specs. Met		Each
For Chamfered Nuts







				Steel

				M120	120.000	164.000	2.000	14.000	5.000	8.000	External	Not Rated	DIN 5406	DIN 981	90391A137	000000