160mm ID Bearings | McMaster-Carr

With thicker inner and outer raceways, these bearings can handle heavier loads than thin-profile crossed roller bearings. Mounting holes on the inner and outer rings allow for fastening onto hollow joints and shafts. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Temp. Range, ° F	Features		Each
For Combined Radial, Thrust, and Moment Load—Open with Steel Ring



		160	295	35	23,350	38,850	350	Lubricated	0 to 175	Lubrication Groove, Two Lubrication Holes	0000000	000000000


		For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring



				160	295	35	23,350	38,850	350	Lubricated	0 to 175	Lubrication Groove, Two Lubrication Holes	0000000	00000000

Needle-Roller Thrust Bearings


Bearings	Washers

Small but mighty, our thinnest rolling thrust bearings slot into tight spaces and spin at whirring speeds. Their long, slender rollers support thrust loads and reduce friction in everything from machine tool spindles to gearboxes.

A cage holds the rollers in place. You can install these bearings without washers between hardened, ground surfaces for the thinnest profile. If you’re working with unhardened, unground surfaces, you’ll need two washers for the rollers to run on. This three-piece design is easy to lubricate, but the oil will attract dust and grime since it’s exposed.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	Thrust Bearings										Thin Washers
	For Shaft Dia., mm	OD, mm	Thk., mm	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F	Specs. Met		Each	Thk., mm		Each
Steel



		160	200	5	Steel	33,200	1,590	0 to 240	DIN 5405-3, ISO 303	00000000	0000000	1	00000000	0000000

Thin-Profile Crossed-Roller Bearings

For a more compact machine, these bearings have thinner inner and outer rings than high-load crossed-roller bearings. Route hydraulic lines, electrical wiring, and other components through the inside of the bearing. The rollers face in alternating directions to allow for rigid, accurate motion under any combination of radial, thrust, and moment (twisting) loads. Use in applications where highly accurate motion is necessary, such as machine tools and industrial robots.

Sealed Bearing—Sealed bearings block out dust and other contaminants better than open bearings, but retain more heat.

				Combined Load Cap., lbf
	For Shaft Dia., mm	For Housing ID, mm	Wd., mm	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	Temp. Range, ° F	Features		Each
For Combined Radial, Thrust, and Moment Load—Sealed with Steel Ring



		160	166	13	5,200	10,050	230	Lubricated	0 to 175	Four Lubrication Holes	0000000	0000000

Washers for Needle-Roller Thrust Bearings

Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.

For Shaft Dia., mm	OD, mm	Thk., mm	Washer Material	Specs. Met		Each
160	200	1	Steel	DIN 5405-3, ISO 303	00000000	0000000