About Plain Bearings
More
About Ball and Roller Bearings
More
One-Piece Thrust Ball Bearings
In addition to handling higher loads than three-piece ball bearings, one-piece bearings are easier to handle. They have an outer band that holds the bearing together and acts as a shield against dust and other contaminants.
Thrust Load Cap., lbs. | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Ring Material | Dynamic | Static | Max. Speed, rpm | Lubrication | Temp. Range, °F | Features | Each | |
Shielded | |||||||||||
| 2 1/8" | 3 19/32" | 13/16" | Steel | 11,100 | 30,000 | 2,000 | Required | -40° to 245° | Lubrication Hole | 00000000 | 0000000 |
High-Load Dry-Running Thrust Bearings
A steel backing adds strength to these slippery PTFE bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
| OD | Thick. | Dynamic Thrust Load Capacity | Temperature Range, °F | Each | |
Steel-Backed PTFE Plastic Bearings | |||||
|---|---|---|---|---|---|
For 2 1/8" Shaft Dia. | |||||
| 3 1/8" | 3/32" | 17,100 lbs. @ 30 rpm | -320° to 530° F° | 0000000 | 000000 |
Oil-Embedded Thrust Bearings
Startup friction causes these porous bronze bearings to release a thin layer of oil on the bearing’s surface. They are also known as Oilite® bearings.
Note: Dynamic load capacity is the maximum load a bearing can withstand at a given shaft speed. If your application’s load and speed requirements are below the values listed, the bearing will work.
| OD | Thick. | Dynamic Thrust Load Capacity | Lubrication | Lubricant | Temperature Range, °F | Each | |
For 2 1/8" Shaft Dia. | |||||||
|---|---|---|---|---|---|---|---|
| 4" | 1/8" | 14,000 lbs. @ 30 rpm | Lubricated | SAE 30 Oil | -35° to 300° | 0000000 | 000000 |
Needle-Roller Thrust Bearings
Thinner rollers allow these bearings to fit in tighter spaces than tapered-roller thrust bearings. Because of the large contact area between the rollers and washers (not included), these bearings are great for medium to heavy duty, low-friction jobs. For use on hardened and ground surfaces.
Washers allow you to use the bearing on unhardened and unground surfaces.
Thrust Load Cap., lbs. | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | OD | Thick. | Dynamic | Static | Max. Speed, rpm | Lubrication | For Shaft Surface Smoothness (Ra), microns | Temp. Range, °F | Each | |
Steel Rollers | ||||||||||
Open | ||||||||||
| 2 1/8" | 2 7/8" | 0.0781" | 5,450 | 30,800 | 5,800 | Required | 0.2 | 0° to 240° | 00000000 | 00000 |
Easy-Align Mounted Ball Bearings with Two-Bolt Flange
An elongated mounting hole on one side of the flange lets you adjust the position of these bearings without having to remove your shaft. You only need to loosen the bolt instead of removing it to adjust. They’re self-aligning to compensate for shaft misalignment.
Overall | Mounting | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Ht. | Lg. | Wd. | Flange Thick. | Hole Dia. | Hole Lg. | Hole Ctr.-to-Ctr. | Dynamic | Static | Max. Speed, rpm | Temp. Range, ° F | Alignment Style | Lubrication | Each | |
Sealed Steel Bearings with Cast Iron Housing | |||||||||||||||
Shaft Mount Type: Set Screw | |||||||||||||||
| 2 1/8" | 5 1/4" | 8 1/2" | 2 5/16" | 25/32" | 5/8" | 3 3/8" | 7 1/4" | 9,750 | 6,600 | 2,500 | 0° to 210° | Self Aligning | Lubricated | 0000000 | 000000 |
Hub-Mount Screw-Clamp Bushings
Transfer torque directly from a shaft to a hub. These bushings install over your hub to mount a sprocket, pulley, or gear to a shaft at the same time. Common in industrial gearbox applications, they can also connect a hollow shaft over a solid shaft. As screw-clamp bushings, they're good for shock loads. When you tighten the included clamping screws, the outer rings compress against a sprocket, pulley, or gear in between them, causing the inner rings to tighten around the shaft.
| For Shaft Dia. | OD | Overall Wd. | Max. Torque, in.-lbs. | Fastener Tightening Torque, in.-lbs. | Material | Each | |
| 2 1/8" | 3 15/16" | 1 5/16" | 12,150 | 100 | Zinc-Plated Steel | 0000000 | 0000000 |
Taper-Lock Bushings
Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing style. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.
Keyway | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| For Shaft Dia. | Overall Wd. | Wd. | Dp. | Taper | Fastener Tightening Torque, in.-lbs. | Material | Includes | Each | |
2012 Style Bushing | |||||||||
| 2 1/8" | 1 1/4" | 1/2" | 3/16" | 8° | 280 | Steel | Machine Key, Set Screws | 000000000 | 000000 |
2517 Style Bushing | |||||||||
| 2 1/8" | 1 3/4" | 1/2" | 1/4" | 8° | 430 | Steel | Set Screws | 000000000 | 00000 |
3020 Style Bushing | |||||||||
| 2 1/8" | 2" | 1/2" | 1/4" | 8° | 800 | Steel | Set Screws | 000000000 | 00000 |
Quick-Disconnect (QD) Bushings
The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.