1 5/8" Bearings | McMaster-Carr

Filter by

Product Family

Ball Bearings

Bearing Adapter Sleeves

Flanged Sleeve Bearings

Mounted Bearings

Pulley and Sprocket Bushings

Roller Bearings

Sleeve Bearings

Thrust Bearings

System of Measurement

Shaft Diameter

Bearing Seal Type

Bearing Type

Material

Mounted Bearing Type

Three-Bolt Flange Mount

Two-Bolt Flange Mount

For Load Direction

Combined Radial and Thrust

Width

Shaft Mount Type

Length

Shaft Type

For Housing ID

Plain Bearing Type

Lubrication

DFARS Specialty Metals

Exempt

Dynamic Radial Load Capacity

Less than 10,000 lb.

10,000 lb. to 19,999 lb.

Ball Bearing Profile

Bearing Trade Number

RoHS

Dynamic Thrust Load Capacity

Less than 10,000 lb.

10,000 lb. to 19,999 lb.

20,000 lb. to 99,999 lb.

U.S.–Mexico–Canada Agreement (USMCA) Qualifying

Yes

REACH

Compliant

Not Compliant

Export Control Classification Number (ECCN)

Thickness

45 Products

Extreme-Load Tapered-Roller Thrust Bearings

With thick, tapered rollers, these thrust bearings are the strongest we offer. The rollers spin inside a raceway instead of a cage, so there’s room for more rollers to support higher loads than three-piece designs. You’ll often find them on crane hooks and kingpins that connect semi-trailers to semi-tractors. However, they rotate at a fraction of the speed of other roller thrust bearings.

Since they come as one piece, you don’t need to assemble cages and washers to install. An outer band holds the rollers inside the raceway, keeping lubricant in and dirt out.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Open—With no rubber seal to block airflow, these bearings dissipate heat quickly, extending the life of the lubricant and reducing friction over time.

Sealed—The best choice for dirty environments. In addition to a band, these bearings also have a rubber seal to block dust from creeping in and wearing down the rollers. However, they retain the most heat since air can’t flow through.

	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F		Each
Steel







	Open

	1 5/8"	2.869"	0.8438"	20,500	10	0 to 150	2291N108	000000




			Sealed

			1 5/8"	2.98"	0.8438"	20,500	10	0 to 150	2291N109	00000

Quick-Mount Ball Bearings

Set-Screw

Shaft Mount

Slip onto a shaft and secure with the turn of a screw. You don't need any special tools to mount these bearings.

Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place. For high-speed applications, consider clamp-on shaft mounts, which are less likely to slip.

Black-Oxide Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

Sealed—The best choice for dirty environments. A barrier seals out dust so it won't gunk up or wear down the balls. However, these bearings retain the most heat since air can't flow through.

ABEC Rating—Bearings with an ABEC rating meet industry tolerance standards established by the Annular Bearing Engineers Committee (ABEC). They're rated on a scale from 1 to 9. The higher the rating, the tighter the tolerance. Bearings rated ABEC 1 or 3 are precise enough for most applications. If your application consistently runs at high speeds or requires high accuracy, consider bearings rated ABEC 5 or higher, since they generate less friction and heat.

				Retaining Ring						Temp. Range, ° F
	For Shaft Dia.	For Housing ID	Wd.	OD	Thk.	Bearing Seal Type	ABEC Rating	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Min.	Max.	Bearing Trade No.		Each
Set-Screw Shaft Mount







				Black-Oxide Steel

				1 5/8"	3 11/32"	1 3/32"	3 19/32"	0.063"	Sealed	1	7,900	3,800	-20	220	ER26	8090T34	0000000

Needle-Roller Bearings

Also known as drawn-cup roller bearings, these are our thinnest roller bearings. The outer ring is drawn out to form a lip that holds the bearing together. Bearings take on the shape of their housing and may be oblong prior to installation.

Open Bearing—Open bearings dissipate heat more efficiently than sealed bearings.

				Radial Load Cap., lb.
	For Shaft Dia.	For Housing ID	Wd.	Dynamic	Static	Max. Rotation Speed, rpm	Lubrication	For Shaft Surface Smoothness, Ra, μin	Temp. Range, ° F	Specs. Met		Each
For Radial Load—Open with Steel Ring



		1 5/8"	2"	5/8"	5,700	8,900	6,200	Required	8	-40 to 280	—	5905K344	000000


		1 5/8"	2"	1 1/4"	11,400	21,800	6,000	Required	8	-20 to 280	ISO 281, ISO 76	5905K524	00000

Oil-Embedded Flanged Sleeve Bearings

Install and forget these self-lubricating bearings. All are made from porous metal and saturated with oil to reduce maintenance and downtime. A good all-around choice, they are used in everything from palm-sized fans in electronics to tire-sized pulleys. Although these bearings will work in most conditions, oil may drip away if temperatures get too high. Consider a graphite-lubricated bearing for higher temperatures or places where you can’t afford the mess. All are fabricated, lubricated, and inspected in the U.S.

Flanged sleeve bearings combine a sleeve and thrust bearing in one. The flange supports thrust loads and prevents the bearing from being pushed out of place. The sleeve is the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

High-Load 863 Iron Copper—Iron makes these bearings harder, stronger, and more resistant to sudden starts and stops than 841 bearing bronze. However, they operate at slower speeds. The increased iron content makes these bearings appear silver.

Extreme-Load Heat-Treated Iron Copper—Our strongest oil-embedded flanged sleeve bearings. They’re heat treated to form a uniform internal grain that makes them stronger than 863 iron copper. As a result, they’re often used to support extreme loads in earth-moving equipment and railroad applications. The increased iron content makes these bearings appear silver.

Mineral Oil Base—Mineral oil consistently lubricates at most temperatures but doesn’t last as long as synthetic oil.

Synthetic Oil Base—A high-quality lubricant makes all the difference. Synthetic oil is less sensitive to temperature changes than mineral oil, so it won't get runny and leak away at higher temperatures.

	For Housing ID	Lg.	Flange OD	Flange Thk.	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	1 5/8"	2"	2"	2 1/4"	3/16"	6,500 lb. @ 30 rpm	3,800 lb. @ 30 rpm	Synthetic Oil	-35 to 300	6338K599	000000


	High-Load 863 Iron Copper



			1 5/8"	2"	2"	2 1/4"	3/16"	8,900 lb. @ 30 rpm	3,750 lb. @ 30 rpm	Synthetic Oil	-15 to 300	2938T72	00000


			Extreme-Load Heat-Treated Iron Copper



					1 5/8"	2"	2"	2 1/4"	3/16"	19,050 lb. @ 30 rpm	8,050 lb. @ 30 rpm	Mineral Oil	10 to 220	3731K28	00000

Mounted Ball Bearings

Smoother than smooth—the balls inside these bearings roll nearly friction-free. The sturdy housing bolts down to support shafts as they turn.

Lubricate regularly to keep your bearing in tip-top shape. Bearings with seals and shields keep lubricants in and contaminants out, and come packed with grease. Open bearings require initial lubrication and offer less protection against dust and debris.

Nickel-Plated Cast Iron Housing—Combine the strength of iron with the corrosion resistance of stainless steel at an affordable price point. Nickel-plated iron is also unlikely to chip.

Set Screw—Turn the screw to lock your shaft in place. A simple, reliable choice, set screws grip tightly, but they can mar shaft surfaces.

Misalignment Capability—Bearings compensate for as much shaft misalignment as the degree listed. This extends the life of the bearing and protects against wear if shafts are slightly askew.

			Overall
	For Shaft Dia.	Ctr. Ht.	Lg.	Wd.	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Bearing Material	Bearing Seal Type	Misalignment Capability	Manufacturer		Each
Nickel-Plated Cast Iron Housing







				Set Screw

				1 5/8"	2 1/8"	7 15/32"	2 1/4"	7,650	3,000	Steel	Sealed	2°	McMaster-Carr Approved	6494K76	000000

Bearing Adapter Sleeves

Make up for imperfections and gaps between your bearing and shaft for a tight fit. These bearing adapter sleeves are the most common way to mount a bearing with a tapered bore onto a cylindrical seat. They work with both straight and stepped shafts. Secure using the included lock nut.

Inch

	For Shaft Dia.	ID	Wd.	Includes		Each
Low-Carbon Steel



	SNW-10	1 5/8"	1 5/8"	1.775"	Lock Nut, Lock Washer	4449N15	000000

Insert Bearings

Install by hand into a housing (sold

separately)

Image of Product. Front orientation. Ball Bearings. Insert Bearings.

Swap out worn inserts instead of replacing the entire mounted unit. To choose an insert, match the manufacturer model number on your existing bearing.

Set-Screw Shaft Mount—Tighten the screws against the shaft to hold the bearing in place, regardless of the direction the shaft spins.

					Temp. Range, ° F
	For Shaft Dia.	For Mounted Bearing Model No.	Bearing Material	ABEC Rating	Min.	Max.		Each
For Timken Mounted Bearings







				Set-Screw Shaft Mount

				1 5/8"	SAK 1 5/8, SAS 1 5/8, SCJ 1 5/8, SCJT 1 5/8, STB 1 5/8	Steel	1	-65	250	4768K39	0000000

Ultra-Low-Friction Oil-Embedded Flanged Sleeve Bearings

Our slipperiest metal bearings, these are ideal for machinery with frequent starts and stops, such as conveyors. With nonstick PTFE particles added to the oil, they reduce friction to minimize wear and heat, so equipment runs more efficiently and lasts longer. All are fabricated, lubricated, and inspected in the U.S.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

	For Housing ID	Lg.	Flange OD	Flange Thk.	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Base Oil	Lubricant Additive	Temp. Range, ° F		Each
841 Bearing Bronze



	1 5/8"	2"	2"	2 1/4"	3/16"	6,500 lb. @ 30 rpm	3,750 lb. @ 30 rpm	Synthetic Oil	PTFE	-140 to 460	1677K395	000000

Oil-Embedded Sleeve Bearings

With no moving parts, sleeve bearings are the simplest way to support the load of a rotating shaft while reducing friction. Also known as plain bearings.

841 Bearing Bronze—A classic choice for a starter pick. Also known as SAE 841 bearings.

Mineral Oil Base—Mineral oil consistently lubricates at most temperatures but doesn’t last as long as synthetic oil.

	For Housing ID	Lg.	Dynamic Radial Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	1 5/8"	1 7/8"	1"	3,250 lb. @ 30 rpm	Mineral Oil	10 to 220	6391K592	00000


	1 5/8"	1 7/8"	1 1/4"	4,050 lb. @ 30 rpm	Mineral Oil	10 to 220	6391K593	00000
	1 5/8"	1 7/8"	1 1/2"	4,850 lb. @ 30 rpm	Synthetic Oil	-35 to 300	6391K823	00000
	1 5/8"	1 7/8"	1 3/4"	5,650 lb. @ 30 rpm	Mineral Oil	10 to 220	6391K594	00000
	1 5/8"	1 7/8"	2"	6,500 lb. @ 30 rpm	Synthetic Oil	-35 to 300	6391K676	00000
	1 5/8"	2"	1 1/2"	4,850 lb. @ 30 rpm	Synthetic Oil	-35 to 300	6391K677	00000
	1 5/8"	2"	2"	6,500 lb. @ 30 rpm	Synthetic Oil	-35 to 300	6391K489	00000
	1 5/8"	2"	2 1/2"	8,100 lb. @ 30 rpm	Mineral Oil	10 to 220	6391K595	00000
	1 5/8"	2"	3"	9,750 lb. @ 30 rpm	Synthetic Oil	-35 to 300	6391K824	00000

Easy-Adjust Mounted Ball Bearings with Two-Bolt Flange

Change the position of your bearing without having to remove your shaft. Just loosen the bolt in the elongated mounting hole for quick adjustments. The housing mounts in place with a two-bolt flange, the most common type of flanged bearing. Inside, the balls roll nearly friction-free to support smooth rotation.

Lubricate regularly to keep your bearings in tip-top shape. These bearings come packed with grease and sealed to block out dust and contaminants.

Powder-Coated Cast Iron Housing—A rugged iron base coated in thick powder that protects against water, mild detergents, and oil. However, if the coating is scratched or chipped, the underlying iron may rust.

Set Screw—Turn the screw to lock your shaft in place. A simple, reliable choice, set screws grip tightly, but they can mar shaft surfaces.

Misalignment Capability—Bearings compensate for as much shaft misalignment as the degree listed. This extends the life of the bearing and protects against wear if shafts are slightly askew.

		Overall
	For Shaft Dia.	Lg.	Wd.	Flange Thk.	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Bearing Material	Bearing Seal Type	Misalignment Capability		Each
Powder-Coated Cast Iron Housing







				Set Screw

				1 5/8"	7 1/16"	2 1/16"	9/16"	7,650	3,000	Steel	Sealed	2°	4451N27	000000

Flanged Sleeve Bearings

These bearings don’t come with a lubricant, so you can select the oil that meets the needs of your application. You’ll need to refill the oil, so make sure the bearing is located where you can access it. All are fabricated and inspected in the U.S.

High-Load 932 Bearing Bronze—These bearings are strong enough for sudden starts and stops, plus they resist wear and tear. They are cast from an alloy of leaded tin bronze for uniform rigidity and strength. Also known as 660 leaded bronze bearings.

	For Housing ID	Lg.	Flange OD	Flange Thk.	Dynamic Radial Load Cap. @ Speed	Dynamic Thrust Load Cap. @ Speed	Temp. Range, ° F		Each
High-Load 932 Bearing Bronze



	1 5/8"	2"	2"	2 1/4"	3/16"	13,000 lb. @ 30 rpm	7,600 lb. @ 30 rpm	-350 to 450	7815K837	000000

Oil-Embedded Thrust Bearings

Our simplest-to-use thrust bearings, with no moving parts and no need to lubricate. Their porous surface releases oil over time, so you can install and forget them. While they run in most conditions, oil may drip away if temperatures climb too high. For extremely hot environments, consider graphite-lubricated bearings. All are fabricated, lubricated, and inspected in the U.S.

841 Bearing Bronze—A balance of strength and speed makes these bearings a good choice for most applications. Also known as SAE 841 bearing bronze.

	OD	Thk.	Dynamic Thrust Load Cap. @ Speed	Base Oil	Temp. Range, ° F		Each
841 Bearing Bronze



	1 5/8"	2 1/2"	1/8"	7,000 lb. @ 30 rpm	Synthetic Oil	-35 to 300	5906K618	000000

Mounted Tapered-Roller Bearings

Support heavier loads than mounted ball or needle-roller bearings, but at lower speeds. These bearings also withstand thrust loads, which are forces acting parallel to the shaft. The sturdy housing bolts down to support shafts as they turn.

Lubricate your bearings regularly to keep them in tip-top shape. These bearings come packed with grease and sealed to block out dust and contaminants.

Set Screw—Turn the screw to lock your shaft in place. A simple, reliable choice, set screws grip tightly, but they can mar shaft surfaces.

			Overall		Dynamic Load Cap., lb.
	For Shaft Dia.	Ctr. Ht.	Lg.	Wd.	Radial	Thrust	Max. Rotation Speed, rpm	Bearing Material	Bearing Seal Type		Each
Powder-Coated Cast Iron Housing







				Set Screw

				1 5/8"	2 1/8"	7 7/8"	3 3/8"	7,850	2,550	3,300	Steel	Sealed	1495N14	0000000

One-Piece Thrust Ball Bearings

No need to assemble cages and washers—these thrust ball bearings come as one piece for easy installation. The balls spin inside a raceway instead of a cage, so there's room for more balls to support higher loads than three-piece bearings. An outer band holds the balls inside the raceway, keeping lubricant in and dirt out.

Steel—Strong and wear resistant. However, these bearings are best for dry environments since moisture will cause them to rust.

	OD	Thk.	Cage Material	Dynamic Thrust Load Cap., lb.	Max. Rotation Speed, rpm	Temp. Range, ° F		Each
Steel



	1 5/8"	2 31/32"	13/16"	Steel	10,300	2,400	-40 to 245	60715K31	000000

Extra-Clearance Mounted Ball Bearings

Good for bulky setups, the tall design doubles the clearance between the shaft and the mounting surface. The balls roll nearly friction-free within a sturdy housing to support smooth rotation.

Lubricate regularly to keep your bearings in tip-top shape. These bearings come packed with grease and sealed to block out dust and contaminants.

Set Screw—Turn the screw to lock your shaft in place. A simple, reliable choice, set screws grip tightly, but they can mar shaft surfaces.

Misalignment Capability—Bearings compensate for as much shaft misalignment as the degree listed. This extends the life of the bearing and protects against wear if shafts are slightly askew.

			Overall
	For Shaft Dia.	Ctr. Ht.	Lg.	Wd.	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Bearing Material	Bearing Seal Type	Misalignment Capability		Each
Powder-Coated Cast Iron Housing







				Set Screw

				1 5/8"	4 9/64"	7 15/32"	2 3/4"	7,650	3,000	Steel	Sealed	2°	4453N27	000000

Mounted Ball Bearings with Three-Bolt Flange

Smoother than smooth—the balls roll nearly friction-free within a sturdy housing to support shafts as they turn. A good choice for tight spaces, these bearings mount with a three-bolt flange that only requires access from one side during installation.

Lubricate regularly to keep your bearing in tip-top shape. These bearings come packed with grease and sealed to block out dust and contaminants.

Nickel-Plated Cast Iron Housing—Combine the strength of iron with the corrosion resistance of stainless steel at an affordable price point. Nickel-plated iron is also unlikely to chip.

Set Screw—Turn the screw to lock your shaft in place. A simple, reliable choice, set screws grip tightly, but they can mar shaft surfaces.

Misalignment Capability—Bearings compensate for as much shaft misalignment as the degree listed. This extends the life of the bearing and protects against wear if shafts are slightly askew.

			Overall
	For Shaft Dia.	Ctr. Ht.	Lg.	Wd.	Flange Thk.	Dynamic Radial Load Cap., lb.	Max. Rotation Speed, rpm	Bearing Material	Bearing Seal Type	Misalignment Capability		Each
Nickel-Plated Cast Iron Housing







				Set Screw

				1 5/8"	4 1/4"	4 3/16"	1 31/32"	23/32"	7,650	3,000	Steel	Sealed	3°	8260K52	000000

Dry-Running Metal-Reinforced Plastic Thrust Bearings

Combine naturally slippery PTFE with the strength of metal. These bearings don't need lubricant, so there's no oil to maintain, drip off, or attract dust. Backed with steel, they're as strong as other all-metal thrust bearings. However, they're best for dry environments since moisture will cause the steel to rust.

	OD	Thk.	Dynamic Thrust Load Cap. @ Speed	Temp. Range, ° F		Each
Steel-Backed PTFE



	1 5/8"	2 5/8"	1/16"	16,500 lb. @ 30 rpm	-320 to 530	1262N35	00000

Taper-Lock Bushings

Mount these hubless bushings flush into your sprocket or pulley for a slim profile with no protruding screws. They are for use with taper-lock sprockets of the same bushing trade number. As you tighten the included set screws, the bushing grips the shaft and pulls it into your sprocket or pulley.

			Keyway
	For Shaft Dia.	Overall Wd.	Wd.	Dp.	Taper	Fastener Tightening Torque, in·lbf	Includes		Each
Steel







				Bushing Trade Number 1610

				1 5/8"	1"	3/8"	1/8"	8°	175	Machine Key, Set Screws	57095K168	000000




						Bushing Trade Number 1615

						1 5/8"	1 1/2"	3/8"	1/8"	8°	175	Machine Key, Set Screws	57095K194	00000




								Bushing Trade Number 2012

								1 5/8"	1 1/4"	3/8"	3/16"	8°	280	Set Screws	57095K189	00000




										Bushing Trade Number 2517

										1 5/8"	1 3/4"	3/8"	3/16"	8°	430	Set Screws	57095K214	00000




												Bushing Trade Number 3020

												1 5/8"	2"	3/8"	3/16"	8°	800	Set Screws	57095K327	000000


												Cast Iron







																Bushing Trade Number 3030

																1 5/8"	3"	3/8"	3/16"	8°	800	Set Screws	57095K647	000000




																		Bushing Trade Number 3535

																		1 5/8"	3 1/2"	3/8"	3/16"	8°	1,000	Set Screws	57095K377	000000




																				Bushing Trade Number 4040

1 5/8"																				4"	3/8"	3/16"	8°	1,700	Set Screws	57095K715	000000

Quick-Disconnect (QD) Bushings


Clamp-On Shaft Mount

The screw connections on these bushings easily mate to compatible quick-disconnect sprockets and pulleys. Bushings fit quick-disconnect (QD) sprockets and pulleys of the same bushing trade number. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.

		Keyway
	Overall Wd.	Wd.	Dp.	Fastener Tightening Torque, in·lbf	Material	Includes	For Shaft Dia.		Each
Clamp-On Shaft Mount







				Bushing Trade Number SD

				1 13/16"	3/8"	3/16"	108	Sintered Steel	Clamping Screws	1 5/8"	6086K425	000000




						Bushing Trade Number SDS

						1 3/8"	3/8"	3/16"	108	Sintered Steel	Clamping Screws	1 5/8"	6086K325	00000




								Bushing Trade Number SF

								2 1/16"	3/8"	3/16"	360	Sintered Steel	Clamping Screws	1 5/8"	6086K628	00000




										Bushing Trade Number SH

										1 5/16"	3/8"	1/16"	108	Sintered Steel	Clamping Screws, Machine Key	1 5/8"	6086K224	00000




												Bushing Trade Number SK

												1 15/16"	3/8"	3/16"	180	Sintered Steel	Clamping Screws	1 5/8"	6086K525	00000

Split-Tapered Bushings

Steel

The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They're for use with split-tapered sprockets and pulleys of the same bushing trade number. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.

Machine Key—Bushings with a machine key fit into a matching keyway on a sprocket or pulley for high-torque applications.

			Keyway
	For Shaft Dia.	Overall Wd.	Wd.	Dp.	Taper	Fastener Tightening Torque, in·lbf		Each
Steel







				Bushing Trade Number P1 with Clamping Screws, Machine Key

				1 5/8"	1 15/16"	3/8"	5/16"	3°	192	9859T321	000000




						Bushing Trade Number P2 with Clamping Screws, Machine Key

						1 5/8"	2 15/16"	3/8"	5/16"	3°	192	9859T417	00000




								Bushing Trade Number Q1 with Clamping Screws, Machine Key

								1 5/8"	2 1/2"	3/8"	3/16"	3°	348	9859T519	00000