McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    2 Products

    Angle Iron Beam Clamps for Threaded Rods

    Image of System. Front orientation. Beam Clamps. Angle Iron Beam Clamps for Threaded Rods.
    Image of ProductInUse. Shown With One Pair of Angles. Front orientation. Contains Annotated. Beam Clamps. Angle Iron Beam Clamps for Threaded Rods.
    Image of ProductInUse. Shown with Two Pairs of Angles. Front orientation. Beam Clamps. Angle Iron Beam Clamps for Threaded Rods.

    Shown With One Pair of

    Angles

    Shown with Two Pairs of Angles

    A secure way to hang threaded rods from a pair of angles, such as those used in ceiling joists, without the need to drill or weld. These clamps are commonly used to suspend HVAC, conveyor, and other overhead systems. They may also be used to connect two pairs of angles at 90°. Clamps are zinc-plated steel for good corrosion resistance. Each clamp includes a bracket and square washer. Secure with a hex nut (sold separately).
    Capacity is the maximum load for two clamps holding a pair of angles across parallel joists. The values listed are for the maximum distance between joists, which is 6 ft. For shorter distances, capacities are higher.
    Washer
    For Thread Size
    For Angle
    Thk.
    For Max.
    Beam Span, ft.
    Wt. Cap.,
    lb.
    Mount
    Type
    Inside
    Wd.
    Lg.
    Wd.
    Ht.
    Thk.
    Threaded Rod
    Included
    Material
    No.
    Included
    Each
     
    Zinc-Plated Steel
    5/8"-11, 5/8"-183/16" to 1/4"6500Clamp On1 1/2"2 3/8"2"2"1/4"NoSteel10000000000000
     

    Seismic Bracing Mounts

    Image of System. Angle Iron Mount. Front orientation. Contains Annotated. Seismic Bracing Mounts. Seismic Bracing Mounts.
    Image of System. Ceiling Mount. Front orientation. Contains Annotated. Seismic Bracing Mounts. Seismic Bracing Mounts.

    Angle Iron Mount

    Ceiling Mount

    Image of System. Beam Mount. Front orientation. Contains Annotated. Seismic Bracing Mounts. Seismic Bracing Mounts.

    Beam Mount

    These OSHPD preapproved anchors and brackets support threaded-rod-mount hangers during seismic activity. A complete seismic bracing mount system consists of an upper bracket, a lower bracket, and strut or pipe (sold separately). Brackets work with standard-wall (Schedule 40) pipe sizes 1-2 as well as 1 5/8" wide strut channel. Mount the upper bracket directly to a ceiling or other flat surface, or use an anchor to mount the system to angles, beams, and joists.
    Angle Iron Anchor
    Image of Product. Front orientation. Seismic Bracing Mounts. Seismic Bracing Mounts, Angle Iron Anchor.
    Angle iron anchors allow you to mount upper brackets to pairs of angles, such as those used in ceiling joists. Their set screws have heads that break off when the screw is tightened to ensure proper installation.
    For Max.
    Beam Thk.
    Wd.
    Lg.
    Ht.
    Material
    Wt. Cap.,
    lb.
    No. of Set Screws
    Included
    Certification
    Includes
    Each
    3/8"3 5/16"3"2 1/2"Steel1,0002C-UL Listed
    FM Approved
    UL Listed
    OSHPD Preapproved
    		1/2" Bolt and Nut, Set Screws0000000000000
    back to top