Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure. They’re rated IP68 and NEMA 6P, so they withstand use under water and protect electronics inside enclosures from moisture and harsh chemicals. All are made of nylon, making them corrosion and wear resistant. They relieve the strain on a cable when its pulled, extending the life of the cable.

When choosing a size, keep in mind that the sealing nut ID and body ID must be large enough for the end of your cord to fit through with the connector.

For technical drawings and 3-D models, click on a part number.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting. Because they’re IP rated, you can safely submerse them for brief periods of time. They also seal out water from washdowns and dust. All relieve strain on your cord if it’s pulled, prolonging its life.

For technical drawings and 3-D models, click on a part number.

A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable. They are rated IP68 and IP69K for protection from prolonged submersion and high-pressure, high-temperature jets of water. Made of nylon, these cord grips keep electrical assemblies lightweight. They also withstand chemicals and corrosive environments.

For technical drawings and 3-D models, click on a part number.

Able to resist most chemicals and withstand use underwater, these nylon grips are rated IP68 and 69K for protection from continuous submersion and high-pressure, high-temperature jets of water. They are also rated NEMA 4X, 6, and 12 for indoor and outdoor protection against corrosion, water projected from a hose, and dripping oils and lubricants. A rubber bushing and O-ring create a tight seal to prevent liquid from entering the connection. All meet UL 746C f1, so they’re UV resistant and can be used in direct sunlight, as well as UL 94 V-0, which means they’ll self-extinguish within 10 seconds of catching fire and won’t spread flames by dripping. UL listed and CSA certified, they meet U.S. and Canadian safety standards.

Metric Threads are also VDE certified, meaning they meet European safety standards.

For technical drawings and 3-D models, click on a part number.

Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life. They’re good for cords used on handheld equipment. Made of polyamide, they stand up to corrosion and wear.

For technical drawings and 3-D models, click on a part number.

Tighten the screw-down clamp on these grips for superior pull-out resistance while relieving tension at connection points. Grips are rated IP68 for protection from prolonged submersion and IP69K for protection against high-pressure, high-temperature jets of water. A rubber bushing and O-ring create a tight seal to prevent liquid from entering the connection.

For technical drawings and 3-D models, click on a part number.

Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation. Vents on these cord grips equalize pressure between the inside and outside of an enclosure, preventing harmful moisture from forming. They are nickel-plated brass, so they resist corrosion. These cord grips are rated IP66 and IP67 for protection from dust, washdown, and temporary submersion.

For technical drawings and 3-D models, click on a part number.

These cord grips are lightweight yet durable. As you tighten the grip, a nylon inner ring and lubricated rubber bushing secure your cable, prevent overtightening, and create a seal around the cord to block out liquid. The inner rings are colored by size so you can identify them at a glance.

Locknut and O-ring kits (sold separately) create liquid-tight seals between cord grips and enclosure knockouts. When used together with the cord grips, they meet NEMA 4X, NEMA 13, and IP66 ratings, so they can be used indoors and outdoors to protect against corrosion, dust, spraying water, oil, and coolant. Each kit includes two locknuts and one or two O-rings.

For technical drawings and 3-D models, click on a part number.