These carriages and guide rails are steel.

Designed specifically for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

Run many cycles in tight spaces before replacing or re-greasing carriages.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

Adapt most 15 mm guide rails to fit on T-slotted assemblies.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Use these carriages and guide rails in temperatures up to 300° F.

A handle on the side of the carriage locks the carriage in place.

Mate with a T-slotted rail to add linear motion to your assembly.

C-shaped guide rails grip the carriage around the outside to support linear motion along walls and other vertical surfaces.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

Build loops, circuits, and curved paths in assembly stations and other repetitive processes.

A handle on the side of the carriage locks the carriage in place.

Mount along a wall or other vertical surface.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

V-shaped rollers and rails allow these carriages to operate well in dirty environments because the debris won't get trapped on the rail.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Slides have a row of ball bearings on each side of the rail.

Good for use in pick-and-place applications, machine tool doors, and telescopic press arms, these rugged slides are designed to carry heavy loads.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

These shafts include a support rail for a stable setup that eliminates bending and prevents linear bearings from rotating.

Position shafts an inch or two off the ground to maintain bearing and part clearance. Support rails provide stability over the entire length of shaft, allowing virtually unlimited travel lengths and eliminating bending under moderate to heavy loads.

These two-piece supports allow access to the shaft without needing to slide out the shaft or uninstall the support. Use them to brace the end of a linear shaft when working with light to medium loads where shaft alignment is not critical. Tighten the included clamping screws to secure.

Create a support that fits the exact dimensions of your shaft. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

Combine these general purpose shafts with a linear bearing and shaft support to create a basic linear motion system.

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Keep a material certificate on hand for compliance and quality assurance needs. Certificates include a traceable lot number and material test report. These hollow shafts reduce system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Lighter than solid shafts, hollow shafts reduce your total system weight and allow you to run various media such as electrical wiring, compressed air tubing, coolants, or lubricants through the center.

Compatible with THK guide rails, mount these wipers to carriages to sweep chips and other contaminants out of the way as the carriage moves across the rail.