Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

Designed for use on horizontal surfaces, the contact angle of the ball bearings on the rail allows these carriages to last longer than other carriages.

With a wide base and low-profile design, these carriages and guide rails stabilize moment (twisting) and off-center loads better than other carriages and rails. They're good for use in areas where multiple carriages or rails won't fit.

These tiny carriages and guide rails are sized for electronic and other precision applications.

Adapt most 15 mm guide rails to fit on T-slotted assemblies.

A handle on the side of the carriage locks the carriage in place.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

Mate with a T-slotted rail to add linear motion to your assembly.

For applications with low clearance, these carriages protrude less than 5 mm above their rails.

Threaded inserts secure the bearing to the carriage and prevent it from loosening due to frequent starts and stops.

C-shaped guide rails grip the carriage around the outside to support linear motion along walls and other vertical surfaces.

A handle locks these carriages in place on curved paths, loops, and circuits in assembly stations and other repetitive processes.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

Create a self-aligning carriage and guide rail system to compensate for mounting surfaces that aren't parallel.

Use these carriages and guide rails for light loads where precise movement is not required.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

Combine with a T-slotted rail to add linear motion to your assembly.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

A linear scale and micrometer-like hand wheel measure travel distance in increments of 0.001".

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Designed to handle heavy loads, these bearings have the highest load capacities of any mounted linear ball bearings we offer.

Outdoor as well as mild chemical environments are no problem for these bearings. They have stainless steel balls for corrosion resistance.

Made from a single piece of slippery UHMW plastic, these bearings have no cracks or crevices so they’re easy to clean.

A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.

Float bearings on air for precise, frictionless movement. Unlike traditional bearings that can wear your shaft down, these bearings are suspended using pressurized air for linear and rotary motion.

The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings.

The shell, housing, and balls of these bearings are stainless steel for excellent corrosion resistance.

Designed to handle heavy loads, these bearings have higher load capacities than comparable standard mounted linear ball bearings for support rail shafts.

Virtually maintenance free, these bearings have slippery, chemical-resistant liners that don't require added lubrication.

With two bearings mounted in one housing, these sleeve bearings withstand heavy loads. Use them on round support rail shafts for applications that require maximum rigidity.

Engineered for simultaneous linear and rotary motion, these bearings are used with round end-supported shafts.

The choice for low-friction motion in high-temperature environments.

Ridges on the inside of these bearings wipe away dust and debris as the bearing travels on a shaft.

Thinner than standard linear sleeve bearings, these bearings fit where clearance is a concern.

These fiberglass bearings are lightweight, nonmagnetic, and won’t conduct electricity.

The choice for low-friction motion in high-temperature environments.

Sleeve bearings outperform ball bearings in dirty environments. Use them for low speed applications.

These bearings have a ceramic liner to help them achieve high speeds as well as rapid acceleration and deceleration.

Slide up to two linear ball or sleeve bearings into these housings and secure them with the included internal retaining rings.

Choose these metric bolts for fastening most machinery and equipment. They are twice as strong as low-strength steel bolts. Carriage bolts have a smooth, rounded head for a finished look. The square neck keeps these bolts from turning when tightening a nut.

Made from Grade 8 steel, these bolts can be used in high-stress applications, such as valves, pumps, motors, and automotive suspension systems. Carriage bolts have a smooth, rounded head for a finished look. The square neck keeps these bolts from turning when tightening a nut.

More corrosion resistant than 18-8 stainless steel bolts, these bolts have excellent resistance to chemicals and salt water. Carriage bolts have a smooth, rounded head for a finished look. The square neck keeps these bolts from turning when tightening a nut.

These bolts are suitable for fastening most machinery and equipment. Carriage bolts have a smooth, rounded head for a finished look. The knurled neck grips the inside of the hole to keep these bolts from turning when tightening a nut.

Modify the stroke length on these air slides to meet changing application requirements—slides have adjustable shaft collars on the guide rods that you can move to fine-tune the stroke length.

Add your own stepper motor and controller to precisely move the ball screw and carriage smoothly at high speeds, like a head on an inkjet printer.