An enclosed ratchet feed opens quickly to accept tubing and instantly slides to cutting position.

Made of materials that are FM approved, these cutters satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Ratchet action permits cutting in cramped areas.

These heavy duty cutters have an iron frame for exceptional durability.

Cut pipe with just 90°-110° of handle swing and 4" of clearance.

A fast-acting release lever opens the cutter to maximum size. Push the handle to quickly slide the cutting wheel onto the pipe.

Cut plastic and rubber pipe, tubing, and hose.

A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.

Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.

This cutter has two blades that cut a 13/64" wide strip—peel it back for smooth edges with little distortion.

These cutters make straight cuts and curves.

Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Handles are angled to keep your hand away from the material as you cut straight lines and curves.

A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Punch small pieces out of material to create an almost burr-free cut with no material distortion.

Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

Cut soft materials such as PTFE, fiber, rubber, and cork.

Leave clean cut edges in a variety of pliable materials.

Plastic-cushioned grips make these cutters easy to hold during repeated cuts.

Made of beryllium copper that is FM approved, these cutters satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

These powerful cutters make diagonal cuts with a nipping action to cut extra-hard wire with ease.

Use these one-handed cutters on small-diameter aluminum and copper power and communication cable.

Produce clean, distortion-free cuts in cable with one-handed operation.

Push the button to cut aluminum and copper power and communication cable.

Prevent clogging when cutting soft metal—these blades have plenty of space between the carbide-tipped teeth to allow chips to escape.

Cut plastic, wood, and soft metal such as aluminum, brass, and copper.

Also known as Type 27, raised-hub, and depressed-center cutoff wheels, these wheels outperform Type 1 wheels when making flush cuts.

Use these wheels for cutting soft metal, plastic, stone, and wood.

Strengthened edges cut holes up to 4" dia. in fabric, leather, rubber, and soft metal. Also known as arch punches.

For accurate punching of inner and outer holes, these sets come with pilots that attach to the outer hole punch.

Use a wrench to cut DIN-size holes in steel up to 1/16" thick.

The driver supplies eight tons of force to the hole punches in this set to make straight punches.

Create larger holes and make repeated punches with these drivers that supply 11 tons of force to the included hole punches.

Punch conduit up to size 1 1/4.

About half the size of a standard portable lever-operated punch, these punches can fit in your toolbox.

These medium duty tools have more than double the punching force of compact portable lever-operated punches.

A throat depth more than double those of standard bench-mount lever-operated punches allows this tool to reach further past the edge of material.

Our most powerful lever-operated punch, the rotary-action socket turns to deliver two to three times the punching force of other bench-mount lever-operated punches.

Pair these carbide inserts with our Replaceable Carbide-Insert End Mills. They have a mounting hole that allows you to fasten them directly to the end mill body for a hold that's strong enough to handle the high speeds of a CNC machine.

Mill an angled edge to the entire outside diameter of pipe, tubes, and rods in a single pass with more speed and precision than a handheld scraper. These end mills deburr pipe and tube for butt welds and shape rods for sliding into housings and holes.

The diamond tip on these tools offers superior cutting performance on nonferrous and nonmetallic materials, such as aluminum, copper, fiberglass, and plastic.

Choose these premium turning carbide inserts to cut a variety of materials without changing out your tool.

Use these dies to create external threads on bolts, studs, and rods.

Create external pipe and conduit threads.