Made of cotton fabric, these coveralls are treated to protect against low radiant heat and minor sparks when welding. They have five pockets and a flap down the front that conceals the snaps.

All coveralls have an inseam length of 32".

Keep dust, microbes, and other pollutants on your skin or clothing from contaminating a clean room. Wear them once, then throw them away. These coveralls are cleaned and individually bagged in a clean room, so they won’t shed any lint or dust in your space. They’re made of polyethylene/Tyvek fabric, which has fibers bonded under heat and pressure for softness and strength. They hold up to limited contact with nonhazardous liquids, such as water and paint spray. Elastic cuffs fit tightly at your ankles and wrists to block splashes.

Made of self-extinguishing Pyrolon, these coveralls help comply with NFPA 2113 standards when worn over flame-resistant clothing. Pyrolon won’t melt or drip if intermittently exposed to flames, which reduces the risk of burns. These coveralls provide full body coverage and are breathable to keep you cool while working. They have a zipper down the front.

Wear these coveralls for neck-to-ankle protection from electrical arc-flashes and flash fires. They’re bright yellow with reflective strips to help you stand out in busy areas and dim conditions. They meet NFPA 70E and NFPA 2112 standards for protection from arc flashes and flames, as well as ANSI/ISEA 107 standards for visibility. They’re rated Class 3, which means you'll be visible from at least _1/4 of a mile away. Made of a cotton/nylon fabric, these coveralls are soft and wear resistant.

Check the personal protective equipment (PPE) category and minimum arc rating provided for your workplace and select all required clothing and personal protective equipment to meet that rating. These coveralls are rated for Category 2, the most common arc flash rating for industrial applications.

Protect sensitive equipment from damage and malfunction—these coveralls gradually divert static electricity. They have a surface resistivity of 105-106 ohms. Made of a carbon/polyester/ fiber blend, these coveralls are low linting and wrinkle resistant. They have a flap down the front, which conceals the zipper from dirt and grime. They have seven pockets, open cuffs, and an elastic waist.

With bright colors and reflective stripes, these coveralls help you stand out in high-risk areas where visibility is low. They meet ANSI/ISEA 107 Class 3 standards for people who need to be visible from at least a _1/4 of a mile away. Made from polyester fabric, these coveralls are lightweight and wick away moisture to keep you cool. They have seven pockets: five with hook and loop closure to keep items secure, and two that give you access to clothing worn underneath. The elastic ankle cuffs stretch over boots and fit tight to keep dirt and grime out.

Withstand flash fire for up to 8 seconds—the clothes in these kits can protect you for twice as long as most flame-resistant clothing. Made of rayon/aramid, the coveralls and mask absorb moisture to keep you cool and comfortable.

The coveralls have a 10 ft. Kevlar strap, so nearby teammates can pull you to safety without putting themselves at risk if there’s a fire. The reflective stripes keep you easy to see where there's low visibility. The zipper closure on the front is covered by a hook-and-loop flap so it doesn't scrape equipment or get hot. The legs have zippers on the sides as well, so you can fit them over bulky boots. Tighten the hook and loop straps on the bottom of the pants to keep flames out. The sleeves have cuffs with thumb holes to keep the sleeves in place and prevent flames from sneaking in. When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under the coveralls.

Often worn near abrasive blasters, these coveralls shield from dust and debris. A blend of cotton and nylon makes them durable to withstand wear and breathable to keep you comfortable. A second layer of fabric on the knees adds protection, and reinforced seams defend against ripping. These coveralls have a fabric layer that snaps over the zipper to keep from scratching or snagging on nearby machines.

Shield your body from chemical and electrical hazards. These coveralls meet NFPA 1992 to resist 70 different chemicals and NFPA 2112 and 70E for protection against flames and arc flashes. Made of nomex fabric, they’re durable and breathable to keep you comfortable. Sealed seams and a flap over the zipper stop chemicals from reaching your skin.

Check the personal protective equipment (PPE) category and minimum arc rating provided for your workplace and select all required clothing and personal protective equipment to meet that rating. These coveralls are rated Category 2, the most common arc flash rating for industrial applications.

All coveralls have an inseam length of 31".