McMaster-Carr logo
    Filter by
    Platform Height
    Number of Steps
    Ground Clearance Height
    Step Tread
    Overall Height
    Component
    Overall Width
    Overall Depth
    Ground Clearance Depth
    Weight Capacity
    Width
    Platform Width
    Platform Depth
    Number of Mounting Holes
    Step Shape
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    DFARS Specialty Metals
    U.S.–Mexico–Canada Agreement (USMCA) Qualifying
    Industrial Info Snippet
    Platform Tread
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    Help me decide (beta)
    4 Products

    Build-Your-Own Fixed Work Platforms

    Image of System. Shown Assembled. Front orientation. Contains Annotated. Work Platforms. Build-Your-Own Fixed Work Platforms.

    Shown Assembled

    Configure a work platform to fit your application.
    First, determine how high your work platform needs to be and choose the stairs that accommodate that height. Then, choose a platform section based on the desired length. Next, choose platform supports that correspond to the height of your stairs—each end of the platform must be supported by a platform support. Finally, choose handrails for the stairs and platform. Assembled work platforms should be secured to a supporting surface (mounting hardware not included).
    Stairs
    Aluminum—Made of aluminum, these platforms are lightweight and corrosion resistant.
    Serrated Step—Steps are serrated for maximum slip resistance.
    Specifications Met—Work platforms meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices. Work platforms also meet CAL-OSHA standards, which is required for use in California.
    Steps
    Mounting
    Holes
    Platform
    Ht.
    Ground Clearance
    Ht.
    No.
    of
    Wd.
    Dp.
    Tread
    Climbing
    Angle
    Wt. Cap.,
    lb.
    Assembly
    Mounting Hardware
    Included
    No.
    of
    Dia.
    Specs. Met
    Each
    Aluminum
    18"14"124"9 1/2"Serrated45°500UnassembledNo47/16"ANSI/ASSP A1264.1, Cal/OSHA Compliant Title 8 Section 3209, Cal/OSHA Compliant Title 8 Section 3622, OSHA Compliant 29 CFR 1910 Subpart D4198N410000000
     

    Low-Height Crossover Stairs

    Image of Product. Front orientation. Contains Annotated. Crossover Stairs. Low-Height Crossover Stairs, 1 Step.

    1 Step

    Take the safest, shortest route over pipes and other obstacles near the ground. For stability, bolt these stairs to your floor.
    Powder-Coated Steel—Powder-coated steel stairs are both rust resistant and durable enough to withstand heavy use. They’re yellow, so they are easy to see and reduce tripping risks.
    Aluminum—Aluminum stairs are more corrosion resistant than steel stairs. They’re a good choice for damp areas, including outdoors.
    Serrated Step—The serrated steps and platform prevent slipping and allow liquids and debris to pass through.
    Specifications Met—All stairs meet OSHA and Cal/OSHA dimensional and construction standards. Check local, state, and federal codes, including OSHA, for safe set up and operating practices.
    Overall
    Ground
    Clearance
    Platform
    Step
    Mounting
    Holes
    Ht.
    (A)
    Wd.
    (B)
    Dp.
    (C)
    Ht.
    (D)
    Dp. (E)
    Ht.
    Wd.
    Dp.
    Wd.
    Dp.
    Wt. Cap.,
    lb.
    No. of
    Steps
    Mounting Hardware
    Included
    No.
    of
    Dia.
    Assembly
    Specs. Met
    Each
    Yellow Powder-Coated Steel
     
    Flat Step with Serrated Tread
    9"26 1/2"40"6 1/2"24 9/16"9"25 7/8"29"25 7/8"29"5001No49/16"AssembledOSHA Compliant 29 CFR 1910.23, Cal/OSHA Compliant Title 8 Section 36229146N110000000
     
    Aluminum
     
    Flat Step with Serrated Tread
    9"26 1/2"40"6 1/2"24 9/16"9"25 7/8"29"25 7/8"29"3001No49/16"AssembledOSHA Compliant 29 CFR 1910.23, Cal/OSHA Compliant Title 8 Section 36229146N13000000
     

    Nonconductive Build-Your-Own Fixed Work Platforms

    Image of System. Shown Assembled. Front orientation. Contains Annotated. Work Platforms. Nonconductive Build-Your-Own Fixed Work Platforms.

    Shown Assembled

    Image of System. Side1 orientation. Contains Annotated, MultipleImages. Work Platforms. Nonconductive Build-Your-Own Fixed Work Platforms.
    Configure platforms to fit your application.
    First, determine how high your work platform needs to be and choose the stairs that accommodate that height. Then, choose a platform section based on the desired length. Next, choose platform supports that correspond to the height of your stairs—each end of the platform must be supported by a platform support. Finally, choose handrails for the stairs and platform. Assembled work platforms should be secured to a supporting surface.
    Stairs
    Fiberglass—These platforms are nonconductive fiberglass.
    Grit-Coated Step—For good slip resistance, stairs are grit coated.
    Specifications Met—Work platforms meet OSHA dimensional standards. Users are responsible for checking local, state, and federal codes, including OSHA, for safe installation and operating practices. Work platforms also meet CAL-OSHA standards, which is required for use in California.
    Steps
    Platform
    Ht.
    Ground Clearance
    Ht.
    No.
    of
    Wd.
    Dp.
    Finish
    Wt. Cap.,
    lb.
    Color
    Assembly
    Mounting Hardware
    Included
    Specs. Met
    Each
    Fiberglass
    18"11"125 3/4"10 1/2"Grit Coated250GrayUnassembledYesCal/OSHA Compliant Title 8 Section 3642, OSHA Compliant 29 CFR 1910 Subpart D, OSHA Compliant 29 CFR 1910.25, OSHA Compliant 29 CFR 1910.296339T210000000
     
    back to top