McMaster-Carr logo
    Filter by
    System of Measurement
    End Shape
    Shaft Type
    Material
    Pin Type
    End Type
    Fastener Head Type
    Tolerance Rating
    USMCA Qualifying
    Knurl Length
    Minimum Hardness
    Knurl Location
    Knurl Coverage
    Performance
    Double Shear Breaking Strength
    For Use With
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    74 Products

    Fully Knurled Dowel Pins
    3D CAD models available

    Etched around the entire diameter, these pins make more contact with the hole than grooved pins. This gives them better resistance to both pulling and twisting that can displace the pin and damage the hole. They're also the best choice for holding plastic and thin parts together.
    Steel
    Image of Product. Front orientation. Dowel Pins. Fully Knurled, Standard Tolerance, Plain Head.
    Low-Carbon Steel—These pins won't deform from stress and vibration. They're stronger than stainless steel but not quite as strong as alloy steel. Pins perform best in dry environments since moisture will cause them to rust.
    Lg.
    Dia.
    Tolerance
    Double Shear
    Breaking
    Strength
    Min.
    Hardness
    Pkg.
    Qty.
    Pkg.
    Low-Carbon Steel
     
    1/8" Diameter
    1"-0.005" to 0"Not RatedNot Rated1000000000000000
    2"-0.005" to 0"Not RatedNot Rated100000000000000
    3"-0.005" to 0"Not RatedNot Rated100000000000000
     
    3/16" Diameter
    1"-0.005" to 0"Not RatedNot Rated100000000000000
    2"-0.005" to 0"Not RatedNot Rated100000000000000
    3"-0.005" to 0"Not RatedNot Rated100000000000000
     
    1/4" Diameter
    1"-0.005" to 0"Not RatedNot Rated100000000000000
    2"-0.005" to 0"Not RatedNot Rated100000000000000
    3"-0.005" to 0"Not RatedNot Rated100000000000000
     

    Partially Knurled Dowel Pins
    3D CAD models available

    A section of knurls around the entire diameter of these pins make better contact with the hole than partially grooved pins. The knurls resist both pulling and twisting that can displace the pin and damage the hole, while the smooth portion acts as a hinge or pivot.
    Half Knurled
    Image of ProductInUse. Front orientation. Dowel Pins. Standard Tolerance, Partially Knurled, Plain Head, Half Knurled.
    Image of Product. Front orientation. Dowel Pins. Standard Tolerance, Partially Knurled, Plain Head, Half Knurled.
    The most versatile partially knurled pins, these are used in a range of applications, including as rod end linkages, stop pins, and locators. Also known as type H pins.
    Zinc-Plated Carbon Steel—These pins withstand occasional exposure to moisture. However, since friction from moving parts can wear away the finish, they're not ideal for wet environments. While not nearly as corrosion resistant as stainless steel, they are stronger and won’t deform under stress.
    Nominal
    Max.
    Lg.
    Dia.
    Dia.
    Tolerance
    Dia.
    Dia. Tolerance
    Double Shear
    Breaking
    Strength, lbf
    Min.
    Hardness
    Knurl
    Lg.
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Carbon Steel
     
    1/8" Diameter
    1/2"0.125"-0.002" to 0"0.133"-0.002" to 0.002"1,600Not Rated1/4"5000000000000000
    3/4"0.125"-0.002" to 0"0.133"-0.002" to 0.002"1,600Not Rated3/8"500000000000000
    1"0.125"-0.002" to 0"0.133"-0.002" to 0.002"1,600Not Rated1/2"500000000000000
     
    3/16" Diameter
    1/2"0.188"-0.002" to 0"0.198"-0.002" to 0.002"3,300Not Rated1/4"500000000000000
    3/4"0.188"-0.002" to 0"0.198"-0.002" to 0.002"3,300Not Rated3/8"500000000000000
    1"0.188"-0.002" to 0"0.198"-0.002" to 0.002"3,300Not Rated1/2"500000000000000
     
    1/4" Diameter
    3/4"0.25"-0.002" to 0"0.262"-0.002" to 0.002"5,800Not Rated3/8"500000000000000
    1"0.25"-0.002" to 0"0.262"-0.002" to 0.002"5,800Not Rated1/2"500000000000000
    1 1/4"0.25"-0.002" to 0"0.262"-0.002" to 0.002"5,800Not Rated5/8"500000000000000
     
    Center Knurled
    Image of ProductInUse. Front orientation. Dowel Pins. Standard Tolerance, Partially Knurled, Plain Head, Center Knurled.
    Image of Product. Front orientation. Dowel Pins. Standard Tolerance, Partially Knurled, Plain Head, Center Knurled.
    These pins lock in the middle, leaving two smooth ends free. They're often used to create a T-handle, such as on a valve stem to open and close it by hand.
    Zinc-Plated Carbon Steel—These pins withstand occasional exposure to moisture. However, since friction from moving parts can wear away the finish, they're not ideal for wet environments. While not nearly as corrosion resistant as stainless steel, they are stronger and won’t deform under stress.
    Nominal
    Max.
    Lg.
    Dia.
    Dia.
    Tolerance
    Dia.
    Dia. Tolerance
    Double Shear
    Breaking
    Strength, lbf
    Min.
    Hardness
    Knurl
    Lg.
    Pkg.
    Qty.
    Pkg.
    Zinc-Plated Carbon Steel
     
    1/8" Diameter
    1/2"0.125"-0.002" to 0"0.133"-0.002" to 0.002"1,600Not Rated1/4"5000000000000000
    3/4"0.125"-0.002" to 0"0.133"-0.002" to 0.002"1,600Not Rated3/8"500000000000000
    1"0.125"-0.002" to 0"0.133"-0.002" to 0.002"1,600Not Rated1/2"500000000000000
     
    3/16" Diameter
    1/2"0.188"-0.002" to 0"0.198"-0.002" to 0.002"3,300Not Rated1/4"500000000000000
    3/4"0.188"-0.002" to 0"0.198"-0.002" to 0.002"3,300Not Rated3/8"500000000000000
    1"0.188"-0.002" to 0"0.198"-0.002" to 0.002"3,300Not Rated1/2"500000000000000
     
    1/4" Diameter
    3/4"0.25"-0.002" to 0"0.262"-0.002" to 0.002"5,800Not Rated3/8"500000000000000
    1"0.25"-0.002" to 0"0.262"-0.002" to 0.002"5,800Not Rated1/2"500000000000000
    1 1/4"0.25"-0.002" to 0"0.262"-0.002" to 0.002"5,800Not Rated5/8"500000000000000
     

    Wood Dowel Pins
    3D CAD models available

    The choice for joining wood components, these pins won’t scratch or damage surfaces. They expand for a tight fit when glued.
    Wood
    Image of Product. Front orientation. Dowel Pins. Wood Dowel Pins.
    Lg.
    Pkg.
    Qty.
    Pkg.
    Wood
     
    1/4" Diameter
    1"10000000000000000
    1 1/4"1000000000000000
    1 1/2"1000000000000000
    1 3/4"1000000000000000
    2"1000000000000000
    2 1/2"1000000000000000
    3 1/2"10000000000000000
     
    5/16" Diameter
    1"1000000000000000
    1 1/4"1000000000000000
    1 1/2"1000000000000000
    1 3/4"1000000000000000
    2"1000000000000000
    2 1/4"1000000000000000
     
    3/8" Diameter
    1"1000000000000000
    1 1/4"1000000000000000
    1 1/2"1000000000000000
    1 3/4"1000000000000000
    2"1000000000000000
    2 1/2"1000000000000000
    3"1000000000000000
     
    7/16" Diameter
    1 1/2"1000000000000000
    1 3/4"1000000000000000
    2"1000000000000000
     
    1/2" Diameter
    1 1/2"1000000000000000
    2"1000000000000000
    2 1/2"10000000000000000
    3"10000000000000000
    4"10000000000000000
    5"10000000000000000
     
    5/8" Diameter
    2 1/2"10000000000000000
    5"10000000000000000
     
    5 mm Diameter
    25 mm1000000000000000
    30 mm1000000000000000
    35 mm1000000000000000
    50 mm1000000000000000
     
    6 mm Diameter
    25 mm1000000000000000
    30 mm1000000000000000
    40 mm1000000000000000
     
    8 mm Diameter
    25 mm1000000000000000
    30 mm1000000000000000
    32 mm1000000000000000
    35 mm1000000000000000
    38 mm1000000000000000
    50 mm1000000000000000
     
    10 mm Diameter
    30 mm1000000000000000
    40 mm1000000000000000
    50 mm1000000000000000
     
    back to top