6mm Shank Size Drill Bits

Extended Length—Drill through panels and thick workpieces with our longest bits. Their length is good for creating deep holes but makes them less rigid than other bits. As a result, they are more prone to wobbling or breaking, especially when drilling hard materials.

Black Oxide—The dark finish increases wear resistance and reduces friction to improve chip flow, so these bits can last 50% longer than uncoated bits.

Titanium Nitride (TiN) Coated—Drill at higher speeds and last longer than uncoated and oxide-coated bits, especially on tough materials like hardened steel and nickel.

Uncoated—The most economical option, uncoated bits perform best when used on low-carbon steel and aluminum. Polished to reduce friction, they're also known as bright finish bits.

Black/Gold Oxide—Like black oxide, this finish adds wear resistance and reduces friction for improved chip flow. Because it’s less prone to flaking off, it offers better rust protection when bits aren't in use.

					Shank				Each		Package
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each	Pkg. Qty.		Pkg.
Jobbers' Length







				Black Oxide

				6.0	0.2362"	93	45	Round	6 mm	Standard	Dormer Pramet	2958A94	00000	—	———	0




						Titanium Nitride (TiN) Coated

						6.0	0.2362"	93	48	Round	6 mm	Standard	Chicago-Latrobe	8950A18	0000	—	———	0




								Uncoated

								6.0	0.2362"	102	56.4	Round	6 mm	Standard	Viking Norseman Drill	2951A136	0000	—	———	0




										Black/Gold Oxide

										6.0	0.2362"	102	66.7	Round	6 mm	Split	Viking Norseman Drill	30565A283	0000	10	30565A437	000000


										Short Length







														Black Oxide

														6.0	0.2362"	66	16	Round	6 mm	Split	Dormer Pramet	28255A43	0000	—	———	0




																Titanium Nitride (TiN) Coated

																6.0	0.2362"	67	27.9	Round	6 mm	Split	Dormer Pramet	2979N24	0000	—	———	0


																Extended Length







																				Black Oxide

																				6.0	0.2362"	200	138	Round	6 mm	Standard	Dormer Pramet	88455A66	00000	—	———	0


6.0	0.2362"																			315	238	Round	6 mm	Standard	Dormer Pramet	88455A76	00000	—	———	0




		Uncoated

		6.0	0.2362"																	139	79.2	Round	6 mm	Standard	Dormer Pramet	3083A165	00000	—	———	0

Cobalt Steel Drill Bits


Jobbers' Length Round Shank	Short Length Round Shank	Split

Tough and wear resistant, cobalt steel bits last at least twice as long as high-speed steel. They can also run up to 25% faster at higher temperatures without being damaged on hard materials, such as nickel.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Short Length—The most rigid bits for drilling the straightest holes.

Titanium Nitride (TiN) Coated—Drill at higher speeds and last longer than uncoated and oxide-coated bits, especially on tough materials like hardened steel and nickel.

Titanium Aluminum Nitride (TiAlN) Coated—The hardest and most wear-resistant coating, especially at high temperatures. These bits are best for hard and abrasive materials, such as iron, titanium, and fiberglass.

Gold Oxide—Like black oxide, this finish adds wear resistance and reduces friction for improved chip flow. Because it’s less prone to flaking off, it offers better rust protection when bits aren't in use.

Uncoated—Polished to eject chips, these are also known as bright finish bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each
Jobbers' Length







				Titanium Nitride (TiN) Coated

				6.0	0.2362"	94	56.9	Round	6 mm	Split	Dormer Pramet	5058N66	000000




						Titanium Aluminum Nitride (TiAlN) Coated

						6.0	0.2362"	93	48	Round	6 mm	Split	Guhring	2753A173	00000




								Gold Oxide

								6.0	0.2362"	93	45	Round	6 mm	Split	Dormer Pramet	29355A92	0000


								Short Length







												Titanium Nitride (TiN) Coated

												6.0	0.2362"	67	16	Round	6 mm	Split	Chicago-Latrobe	2456N154	00000




														Uncoated

														6.0	0.2362"	67	16	Round	6 mm	Split	Chicago-Latrobe	2456N126	0000

Coolant-Fed Carbide Drill Bits

The hardest and most wear-resistant bits, these deliver coolant to reduce heat and evacuate chips. They are designed for CNC machines that supply coolant through the spindle rather than an external source, such as a hose and nozzle. Coolant flows directly from holes in the bit's tip onto the drilling surface. This speeds up cuts and leads to excellent performance in deep holes and tough materials such as stainless steel and titanium.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Maintenance Length—Shorter than jobbers' length, these bits are more rigid for less wobble when drilling hard material. Also known as mechanics’ bits.

Titanium Aluminum Nitride (TiAlN) Coated—No drill bits last longer. These are the best for high-speed, high-temperature drilling of very hard and abrasive materials, including titanium and fiberglass.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each
Jobbers' Length
Round Shank






				Titanium Aluminum Nitride (TiAlN) Coated

				3.0	0.1181"	67	27.9	Round	6 mm	Four Facet	Garr Tool	2396N213	000000


				4.0	0.1575"	73	36.1	Round	6 mm	Four Facet	Garr Tool	2396N257	00000
				5.0	0.1969"	83	43.9	Round	6 mm	Four Facet	Garr Tool	2396N26	00000
				6.0	0.2362"	83	43.9	Round	6 mm	Four Facet	Garr Tool	2396N268	00000


				Maintenance Length
				Round Shank






								Titanium Aluminum Nitride (TiAlN) Coated

								3.0	0.1181"	64	20.1	Round	6 mm	Four Facet	Garr Tool	2396N634	00000


								4.0	0.1575"	67	23.9	Round	6 mm	Four Facet	Garr Tool	2396N638	00000
								5.0	0.1969"	67	27.9	Round	6 mm	Four Facet	Garr Tool	2396N658	00000
								6.0	0.2362"	67	27.9	Round	6 mm	Four Facet	Garr Tool	2396N663	00000

Carbide Drill Bits

The hardest and most wear-resistant drill bits you can buy. Carbide bits stay sharp at high temperatures and faster speeds for the best performance on hard and difficult-to-machine materials. They last 10 to 20 times longer than their closest alternative, cobalt steel. Carbide can be brittle, however, so these bits require a rigid machine tool holder to prevent breakage and should not be used in hand drilling applications.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Short Length—The most rigid bits for drilling the straightest holes.

Titanium Nitride (TiN) Coated—Drill at higher speeds and last longer than uncoated bits, especially on materials like hardened steel, iron, and stainless steel.

Uncoated—Excellent for a range of materials but won't last as long as coated bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each
Jobbers' Length
Round Shank






				Titanium Nitride (TiN) Coated

				6.0	0.2362"	82	50	Round	6 mm	Four Facet	Ultra Tool	3030A83	000000




						Uncoated

						6.0	0.2362"	82	40	Round	6 mm	Four Facet	Ultra Tool	3030A32	00000


						Short Length
						Round Shank






										Titanium Nitride (TiN) Coated

										6.0	0.2362"	63	25	Round	6 mm	Four Facet	Ultra Tool	27515A717	00000




												Titanium Aluminum Nitride (TiAlN) Coated

												6.0	0.2362"	63	25	Round	6 mm	Four Facet	Ultra Tool	8879A617	00000




														Uncoated

														6.0	0.2362"	63	25	Round	6 mm	Four Facet	Ultra Tool	2956A817	00000

Carbide-Tipped Drill Bits

Jobbers' Length

Round Shank

Short Length

Round Shank

Extended Length

Round Shank


Split	Standard

Performance similar to solid carbide but at a lower price point. Like carbide bits, these are stronger than cobalt and high-speed steel and maintain their sharp edges when drilling abrasive material. However, when drilling tough metals like iron and hardened steel, upgrade to carbide for longer life.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Short Length—The most rigid bits for drilling the straightest holes.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each
Jobbers' Length







				Uncoated

				6.0	0.2362"	102	53.3	Round	6 mm	Standard	Izar	28595A63	000000


				6.0	0.2362"	102	70	Round	6 mm	Split	ICS	28595A27	00000


				Short Length







								Uncoated

								6.0	0.2362"	64	18	Round	6 mm	Standard	Izar	28805A407	00000


								Extended Length







												Uncoated

												6.0	0.2362"	156	81	Round	6 mm	Standard	ICS	29465A113	00000

High-Speed Steel Precise-Cut Drill Bits for Wood

Wear and heat resistant, these stay sharp longer than precise-cut bits made of plain steel. The sharp center point keeps the bit from wandering during drilling to cut accurate straight and overlapping holes, even across the grain. Also known as brad-point bits.

	Max. Drilling Dp., mm	Shank Size, mm	Drill Bit Point Type	Mfr.		Each
Uncoated







	Round Shank

	6.0	0.2362"	90	54	6	Brad	Stern	28205A74	000000

Carbide Drill Bits for Carbon Fiber, Fiberglass, and Graphite

Jobbers' Length

Cut clean holes in abrasive material without fraying or delaminating the surface. Made of carbide, these bits resist wear to retain a sharp edge, even after after hundreds of cuts.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size, mm	Point Angle	Drill Bit Point Type	Bit Style	Mfr.		Each
Jobbers' Length







				Diamond Coated

				6.0	0.2362"	82	50	Round	6	140°	Brad	Fluted	Ultra Tool	3162A62	000000




						Uncoated

						6.0	0.2362"	82	50	Round	6	140°	Brad	Fluted	Ultra Tool	2828A122	00000

Hole-Starting Carbide Drill Bits


Short Length Round Shank	Standard

Harder and more wear resistant than cobalt steel, these carbide bits create an accurate starting place in your workpiece. Cut an indent, then continue drilling with a longer bit. The indent prevents slipping so the final hole is centered and precise. Carbide stays sharp at high temperatures and faster speeds. It can be brittle, however, so these bits require a rigid machine tool holder to prevent breakage and should not be used in hand drilling applications.

Short Length—The most rigid bits for drilling the straightest holes.

Uncoated—Excellent for a range of materials but won't last as long as coated bits.

					Shank				90° Point Angle		120° Point Angle		140° Point Angle
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size, mm	Drill Bit Point Type	Mfr.		Each		Each		Each
Short Length







				Uncoated

				6	0.2362"	63	6	Round	6	Standard	Ultra Tool	2911A623	000000	2911A627	000000	2911A632	000000

High-Speed Steel Drill Bits for Plastic

The precision-ground, 60° point penetrates gradually to prevent cracking and chipping. It also reduces heat that can deform the material. Use these bits for drilling into acrylic, laminate, and other plastics. They're made of wear-resistant high-speed steel.

Jobbers' Length About Jobbers' Length

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size, mm	Point Angle	Drill Bit Point Type	Mfr.		Each
Uncoated



		6.0	0.2362"	93	69	Round	6	60°	Standard	ICS	27465A417	000000

Left-Hand Cobalt Steel Drill Bits

Jobbers' Length

Round Shank

Split

The flutes spiral in the opposite direction of other bits and stay sharp longer than high-speed steel. They’re primarily used to remove stripped screws. Choose a bit that’s slightly smaller than the diameter of the screw’s head. Set your power tool to rotate in reverse. Slowly drill in the center of the screw head, maintaining constant pressure. As the bit penetrates, it will catch onto the screw and reverse it out of the hole. If the screw is badly stripped, you might need to punch a starter hole. Also known as reverse-flute bits.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Uncoated—Polished to eject chips, these are also known as bright finish bits.

					Shank					Each
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		1-9	10-Up
Jobbers' Length







				Uncoated

				6.0	0.2362"	102	70	Round	6 mm	Split	Viking Norseman Drill	3474A58	000000	000000

Carbide Drill Bits for Hardened Steel

Short Length

Round Shank

Split

The hardest and most wear-resistant bits with the longest life. Straight flutes withstand the heavy pressure needed to penetrate hardened steel. These bits cut more aggressively and resist stress better than spiral-flute bits. Carbide stays sharp at high temperatures and faster speeds for the best performance on hard and difficult-to-machine materials. It can be brittle, however, so these bits require a rigid machine tool holder to prevent breakage and should not be used in hand drilling applications.

Short Length—The most rigid bits for drilling the straightest holes.

Uncoated—Excellent for a range of materials but won't last as long as coated bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each
Short Length







				Uncoated

				6.0	0.2362"	63	20	Round	6 mm	Split	Ultra Tool	8842A52	000000

Chip-Clearing High-Speed Steel Drill Bits

Jobbers' Length

High Helix Flute

Round Shank

Jobbers' Length

Parabolic Flute

Round Shank

Split

With flutes that lift chips out of the hole, you don't have to stop drilling to clear these bits manually. They improve coolant flow to dissipate heat and prevent clogs that can damage the bit and ruin the hole. High-speed steel is good for general purpose drilling in most metals.

High Helix Flute—Less aggressive than parabolic flutes for cleaner cuts in soft metals.

Parabolic Flute—A U-shaped groove on the flutes cuts faster and clears chips more quickly than high-helix bits, so these are better for drilling deeper holes.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Black Oxide—The dark finish increases wear resistance and reduces friction to improve chip flow, so these bits can last 50% longer than uncoated bits.

Titanium Nitride (TiN) Coated—Drill at higher speeds and last longer than uncoated and oxide-coated bits, especially on tough materials like hardened steel and nickel.

Uncoated—The most economical option, uncoated bits perform best when used on low-carbon steel and aluminum. Polished to reduce friction, they're also known as bright finish bits.

						Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Flute Type	Type	Size, mm	Drill Bit Point Type	Mfr.		Each
Jobbers' Length







				Black Oxide

				6.0	0.2362"	93	45	High Helix	Round	6	Split	Dormer Pramet	30055A66	000000




						Titanium Nitride (TiN) Coated

						6.0	0.2362"	93	57	Parabolic	Round	6	Split	Dormer Pramet	7333N27	00000




								Uncoated

								6.0	0.2362"	93	45	Parabolic	Round	6	Split	Dormer Pramet	2754A31	0000

Smooth-Finish Carbide Drill Bits


Jobbers' Length Round Shank	Split

With more cutting edges than other drill bits, these cut continuously and consistently for a smoother finish. They also stay centered to produce holes that are straighter and more accurate. However, since there’s less space between the cutting edges, they don’t clear chips as quickly. Made of carbide, these are the hardest and most wear-resistant drill bits you can buy. They stay sharp at high temperatures and faster speeds for the best performance on hard and difficult-to-machine materials. Carbide can be brittle, however, so these bits require a rigid machine tool holder to prevent breakage and should not be used in hand drilling applications.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Uncoated—Excellent for a range of materials but won't last as long as coated bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each
Jobbers' Length







				Uncoated

				6.0	0.2362"	66	28	Round	6 mm	Split	Kyocera	2783A4	000000

Carbide-Tipped Drill Bits for Hardened Steel

Jobbers' Length

Round Shank

Straight flutes withstand the heavy pressure needed to penetrate hardened steel. These bits cut more aggressively and resist stress better than spiral-flute bits. A lower-priced alternative to solid carbide, they stay sharp when drilling abrasive material but won’t last as long.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		Each
Jobbers' Length







				Uncoated

				6.0	0.2362"	102	24	Round	6 mm	Notched	Izar	2973A64	000000

Chip-Clearing Cobalt Steel Drill Bits


Jobbers' Length Parabolic Flute Round Shank	Split

Avoid clogs and dissipate heat with cobalt bits that last at least twice as long as high-speed steel. The flutes clear chips to improve coolant flow and prevent damage to the bit and the hole. They also speed up drilling since you don't have to stop to clear the bit manually.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Uncoated—Polished to eject chips, these are also known as bright finish bits.

						Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Flute Type	Type	Size, mm	Drill Bit Point Type	Mfr.		Each
Jobbers' Length







				Uncoated

				6.0	0.2362"	92	55	Parabolic	Round	6	Split	Viking Norseman Drill	2771N55	00000

Carbide Drill Bits for Sheet Metal


Short Length Round Shank	Standard

The hardest and most wear-resistant bits for sheet metal and thin-wall tubing. They have short flutes that make shallow cuts without snagging and deforming the material. Carbide stays sharp at high temperatures and faster speeds than high-speed steel. It can be brittle, however, so these bits require a rigid machine tool holder to prevent breakage and should not be used in hand drilling applications.

Short Length—The most rigid bits for drilling the straightest holes.

Uncoated—Excellent for a range of materials but won't last as long as coated bits.

					Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	No. of Drilling Ends	Mfr.		Each
Short Length







				Uncoated

				6.0	0.2362"	50	12	Round	6 mm	Standard	1	Ultra Tool	8769A44	000000

Chip-Clearing Cobalt Steel Drill Bits for Nickel and Stainless Steel

Jobbers' Length

Parabolic Flute

Round Shank

Split

Excellent for challenging metals such as stainless steel and nickel alloys, these bits cut aggressively and evacuate chips quickly. The grooved flutes prevent clogs and improve coolant flow to dissipate heat that can damage the bit or your material. Bits are made of tough and wear-resistant cobalt steel.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

						Shank
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Flute Type	Type	Size, mm	Drill Bit Point Type	Mfr.		Each
Jobbers' Length







				Titanium Aluminum Nitride (TiAlN) Coated

				6.0	0.2362"	93	57	Parabolic	Round	6	Split	Guhring	3020A48	000000

Left-Hand High-Speed Steel Drill Bits

Jobbers' Length

Round Shank

Standard

With flutes that spiral in the opposite direction of other bits, these are primarily used to remove stripped screws. Choose a bit that’s slightly smaller than the diameter of the screw’s head. Set your power tool to rotate in reverse. Slowly drill in the center of the screw head, maintaining constant pressure. As the bit penetrates, it will catch onto the screw and reverse it out of the hole. If the screw is badly stripped, you might need to punch a starter hole. Also known as reverse-flute bits. High-speed steel is the versatile choice for drilling most metals.

Jobbers' Length—These bits have the balance of rigidity and length needed for most applications.

Black Oxide—The dark finish increases wear resistance and reduces friction to improve chip flow, so these bits can last 50% longer than uncoated bits.

					Shank					Each
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size	Drill Bit Point Type	Mfr.		1-9	10-Up
Jobbers' Length







				Black Oxide

				6.0	0.2362"	93	48	Round	6 mm	Standard	Dormer Pramet	29855A63	000000	000000

Hole-Starting Cobalt Steel Drill Bits

120° Point Angle

Standard

Create an accurate starting place in your workpiece. Cut an indent with these bits, then continue drilling with a longer bit. The indent prevents slipping so the final hole is centered and precise. Cobalt steel resists wear to stay sharp when cutting hard materials, such as nickel. Also known as spotting drill bits.

Short Length—The most rigid bits for drilling the straightest holes.

Uncoated—Polished to eject chips, these are also known as bright finish bits.

					Shank				90° Point Angle
	Drill Bit Size, mm	Decimal Size Equiv.	Overall Lg., mm	Max. Drilling Dp., mm	Type	Size, mm	Drill Bit Point Type	Mfr.		Each
Short Length







				Uncoated

				6.0	0.2362"	67	20.3	Round	6	Standard	Magafor	27445A91	000000