No need for wiring—these lights plug-in with a two-prong plug.

Mount add-on heads in remote areas to extend emergency lighting.

These lights are UL rated for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Plug in these rechargeable flashlights and they’ll automatically light up when the power goes out.

Attach these tiny flashlights to a grease gun nozzle or air hose to shine light directly onto your work.

Tilt the head on these flashlights to aim light exactly where it's needed. They have a flat bottom, so you can work hands-free without them rolling away.

Made of stainless steel, these pocket-size flashlights have a smooth, easy-to-clean surface.

Always have a flashlight on hand—these attach to a key ring.

Attach mini and full-size flashlights to a hard hat and keep your hands free to work.

Extend light into hard-to-reach spaces by attaching a fiber-optic cable to your flashlight.

Convert incandescent, halogen, krypton, and xenon Maglite flashlights into LED flashlights to produce more light and consume less battery power.

Clip these little flashlights to any surface up to 1/2” thick and keep your hands free for work. They're rated for use in environments where hazardous material is present.

In addition to pivoting 210°, the light heads rotate 360° for directing light exactly where it’s needed. They're rated for use in environments where hazardous material is present.

Because these flashlights are buoyant, they're easy to recover when dropped in the water.

Turn a mini flashlight into a headlamp with these straps.

Safe for use in environments where hazardous material is present.

Gently bend these single-use lightsticks to activate.

Bring light to areas that don't have electrical power service.

A movable head lets you aim light where it’s needed most in areas that don't have electrical power service.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Keep excess cord out of the way—the reel locks the cord at any length and retracts it when not in use.

With a NEMA 4X rating, these lights resist degradation when exposed to corrosive liquids, withstand liquids sprayed during washdowns, and are dust tight.

Rated IP65, these lights are sealed to protect against light washdowns from a garden hose. They have a height-adjustable stand and light heads that pivot up and down to direct light where it's needed.

The handle on this floodlight also acts as a stand—pivot it 360° to aim light where it's needed. This floodlight is small and easy to carry to job sites that don't have electrical power.

Mount this light on a pole to illuminate pedestrian areas such as streets and walkways.

Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

Powered by the sun, these security lights function in areas that don’t have access to electricity. They’re often used to shine light on parking lots, landscaping, signs, entryways, and other outdoor spaces.

Install sockets for medium (standard household) screw-in base light bulbs.

These signs are lit from within for high visibility. They meet UL 924 regulations for visibility.

Use the included bracket to mount these signs perpendicular to a wall or ceiling. They meet UL 924 regulations for visibility.

The pad below the base absorbs shock and vibration.

Place these lights in full sun and their batteries charge during daylight hours. Lights automatically switch on at dusk and off at dawn.

Easier to spot than other strobe lights, these lights emit bursts of multiple flashes.

As small as a hockey puck and compatible with standard 12-volt vehicle plugs, these strobe lights are inconspicuous when not in use and quick to connect.

A series of four flashes per cycle makes these lights more visible than other strobe lights.

Set these portable lights wherever you need a signal light—they don't need to be wired or plugged in.

Mounted on a tripod, these lights stand higher for greater visibility than other strobe lights.

These strobe lights flash multiple times per cycle, making them easier to spot than standard strobe lights.

These lights can switch between continuous, flashing, or revolving.

Mount these lights to the top of towers to warn low-flying aircraft.

Make a custom panel light with your choice of light and lens cap color.

These lights are rated IP69K to withstand high-pressure washdowns, such as those in food and beverage applications.

Lights combine high-visibility strobes with a buzzer that warns workers of hazards even when they’re outside a direct line of sight.

The revolving motion of the light makes these more visible than flashing lights.

Design a stack light with your choice of light pattern and color. Start with a base, then add up to five modules total—twist and lock them together.

Use these lights in tight spaces in place of a tower. They emit three colors from a single lens.

Mount the M22 male thread on the bottom of the light through a hole and then secure using the included nut.

These lights emit three colors from a single lens and can be mounted in tight spaces where a tower will not fit.

These lights have LED bulbs for years of maintenance-free operation and can be wired as either continuous or flashing.

Get notified about equipment issues even when you aren't around your machines. These lights connect to your computer via Ethernet, allowing you to set up email alerts when there is a problem with a machine, server, or conveyor.

When motion is detected from both directions at a two-way corner, these lights flash to alert personnel and prevent collisions.

Bulbs have two filaments, which operate at different brightness levels.

These bulbs are sized to fit tight spaces such as signs, control panels, indicators, and flashlights.

Wire terminals allow you to connect these bulbs to a power source through a panel.

Install miniature light bulbs into control panels, machines, and other devices using bulb holders.

Offset pins on the base lock these bulbs into sockets. One pin is slightly higher on the base than the other pin.

These miniature bulbs are sized to fit older telephone switchboards, signs, instruments, and indicators.

Pins on the base lock these bulbs into sockets to withstand vibration.

Replace screw-in incandescent bulbs in exit signs with longer-lasting, energy-efficient LEDs.