High-Speed Steel Square End Mills
Use these end mills for general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel. They have a square end for milling square slots, pockets, and edges.
End mills with fewer flutes provide better chip clearance for high-volume, high-speed plunge, slotting, and roughing cuts; end mills with more flutes provide a finer finish and operate with less vibration when run at high speeds.
Use uncoated end mills for general purpose milling and short production runs.
Noncenter-cutting end mills are for operations where the peripheral teeth do most of the work, such as shoulder milling, contouring, and finishing. They cannot be used for plunge cuts.
For technical drawings and 3-D models, click on a part number.
| Mill Dia. | Shank Dia. | Lg. of Cut | O'all Lg. | Flute Spacing | Helix Angle | For Use On | End Mill Type | Each | |
Uncoated | |||||||||
|---|---|---|---|---|---|---|---|---|---|
6 Flute | |||||||||
| 1 7/8" | 1 1/4" | 2" | 4 1/2" | Equal | 30° | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | Noncenter Cutting | 0000000 | 0000000 |
High-Speed Steel Corner-Rounding End Mills
Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. They have scooped corners for rounding the sharp edges of your workpiece.
For technical drawings and 3-D models, click on a part number.
| Cut Radius | Tip Dia. | Mill Dia. | Shank Dia. | Overall Lg. | Flute Spacing | For Use On | Each | |
Uncoated | ||||||||
|---|---|---|---|---|---|---|---|---|
4 Flute | ||||||||
| 5/8" | 9/16" | 1 7/8" | 3/4" | 4" | Equal | Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel | 0000000 | 0000000 |
Cobalt Steel Corner-Rounding End Mills
With better heat and wear resistance than high-speed steel, these cobalt steel end mills run at higher speeds and provide better performance on hard material. They have scooped corners for rounding the sharp edges of your workpiece.
For technical drawings and 3-D models, click on a part number.
| Cut Radius | Tip Dia. | Mill Dia. | Shank Dia. | Overall Lg. | Flute Spacing | For Use On | Each | |
Uncoated | ||||||||
|---|---|---|---|---|---|---|---|---|
4 Flute | ||||||||
| 5/8" | 9/16" | 1 7/8" | 3/4" | 4" | Equal | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 0000000 | 0000000 |
High-Speed Steel Dovetail End Mills
Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. They create dovetail slots for connecting two components with a sliding fit.
For technical drawings and 3-D models, click on a part number.
Mill | ||||||
|---|---|---|---|---|---|---|
| Dia. | Thick. | Shank Dia. | O'all Lg. | For Use On | Each | |
Uncoated | ||||||
45° Chamfer Angle | ||||||
| 1 7/8" | 1/2" | 7/8" | 3 1/4" | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 0000000 | 0000000 |
60° Chamfer Angle | ||||||
| 1 7/8" | 13/16" | 7/8" | 3 1/4" | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 0000000 | 000000 |
Cobalt Steel Dovetail End Mills
With better heat and wear resistance than high-speed steel, these cobalt steel dovetail cutters run at higher speeds and provide better performance on hard material. Use them to create dovetail slots for connecting two components with a sliding fit.
For technical drawings and 3-D models, click on a part number.
Mill | ||||||
|---|---|---|---|---|---|---|
| Dia. | Thick. | Shank Dia. | Overall Lg. | For Use On | Each | |
Uncoated | ||||||
45° Chamfer Angle | ||||||
| 1 7/8" | 1/2" | 7/8" | 3 1/4" | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 0000000 | 0000000 |
60° Chamfer Angle | ||||||
| 1 7/8" | 13/16" | 7/8" | 3 1/4" | Aluminum, Brass, Bronze, Hardened Steel, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel | 0000000 | 000000 |