These all-metal expansion joints can handle higher temperatures than rubber expansion joints. They reduce stress, vibration, and noise in piping systems by providing a point of flexibility to absorb movement. Joints are made of 304 stainless steel for very good corrosion resistance. The flanged ends rotate for easy bolt hole alignment during installation. Flanges mate with a same-size flat-surface Class 150 flange with a gasket (sold separately).

These joints weld to unthreaded pipe or another butt-weld fitting for a leak-resistant, permanent connection. They reduce stress, vibration, and noise in metal piping systems by providing a point of flexibility to absorb movement.

The PTFE body on these expansion joints has a super-smooth surface that stands up to corrosive chemicals. Joints have a triple-bulb design that provides excellent vibration absorption, reducing stress on your piping system. The flanges mate with a same-size flat-surface Class 150 flange without the need for a gasket. Limit rods are attached to the flanges to prevent overextension.

Because the flanges are molded into the body for a wide sealing surface, these joints provide a tighter seal than other expansion joints. Each flange is supported by a zinc-plated steel plate. Flanges mate with a same-size flat-surface Class 150 flange without the need for a gasket. Joints reduce stress, vibration, and noise in metal piping systems by providing a point of flexibility to absorb movement. They have a flexible body that is reinforced with cord for added strength.

Mount these expansion joints as close as possible to anchor points.

These expansion joints have a double-bulb design for extra movement and vibration absorption. The flanged ends rotate for easy bolt hole alignment during installation. They mate with a same-size flat-surface Class 150 flange without the need for a gasket. Joints have a flexible body that is reinforced with nylon for added strength.

Connect different pipe sizes in your line while adding a point of flexibility between them. These expansion joints absorb movement between two connected pipes to reduce stress, vibration, and noise. Their flanged ends mate with same-size Class 150 flanges without the need for a gasket. Each flange is supported by a zinc-plated steel plate. The body of these expansion joints is reinforced with cord for added strength.

Your pipe system must be rigidly anchored on both sides of the expansion joint to control expansion or contraction of the line. When proper anchoring cannot be provided, limit rods (sold separately) are required.

These joints reduce stress, vibration, and noise in plastic piping systems by providing a point of flexibility to absorb movement. Joints provide a tighter seal than other expansion joints because the flanges are molded into the body for a wide sealing surface. Each flange is supported by a zinc-plated steel plate. Flanges mate with a same-size flat-surface Class 150 flange without the need for a gasket.

Position the expansion joints as close as possible to anchor points.

The EPDM lining in these joints meets NSF/ANSI 61 standard for use with drinking water. To reduce stress, vibration, and noise in piping systems, they provide a point of flexibility to absorb movement. These joints have a flexible body reinforced with polyester plastic cord for added strength. A zinc-plated steel plate supports each flange. The flanges mate with the same-size flat-surface Class 150 flange without the need for a gasket.

Position the expansion joints as close as possible to anchor points.

Slip these joints over your pipe ends and tighten the band clamps for a secure hold. Joints have a triple-bulb design that provides excellent vibration absorption to reduce stress on your piping system. They also have reinforcing rings for extra support during pressure surges and in vacuum applications.

Reduce stress, vibration, and noise in your plastic socket-connect piping system by creating a point of flexibility. These expansion joints have a double-bulb design, so they absorb even more movement and vibration than other expansion joints. Their body is EPDM that's reinforced with nylon for added strength.

Warning: Never use plastic pipe fittings and pipe with compressed air or gas.

These joints are designed for vertical use to reduce stress, vibration, and noise in drain, waste, and vent systems. Slip them over the end of your pipe and tighten the band clamps for a secure hold. They have an internal stop to ensure pipe is in the proper position.