These face masks meet NFPA 70E standards for protection against electrical arc flashes for personal protection equipment (PPE) category 2. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance. These hats are made of abrasion-resistant aramid/viscose blend fabric, which keeps you warm without accumulating moisture.

Protect your head from electrical arc flashes. These face masks won’t melt or drip when exposed to intermittent flames. They meet NFPA 70E standards for personal protection equipment (PPE) category 2. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance. Masks are soft, breathable, and washable.

Protect your head and neck from extreme heat. To fit your head, these hoods use an adjustable ratchet suspension. There's enough room inside to wear glasses, goggles, or a respirator.

Keep a dedicated area for finishing so you can maintain a safe, clean environment. Booths contain overspray and discharge fumes as you paint. They ship unassembled. Motor is UL listed.

Get up close to your welds with these goggles. Their lightweight, compact design lets you weld in tight spots or awkward positions. A flame-resistant hood shields your ears, head, and neck from sparks and spatter better than traditional welding helmets. For different protection needs, wear them over prescription glasses, under a hard hat, or without the hood. Use the external controls to adjust power and shade settings without removing these goggles.

As you begin to weld, two sensors detect the light and automatically darken the lens. Unlike traditional green welding lenses, these goggles use a true color lens to enhance clarity and color accuracy. They allow for a better look at your weld pool to increase weld quality and reduce eye strain.

These hoods meet NFPA 70E standards for protection against electrical arc flashes for personal protection equipment (PPE) category 4. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance. Each hood has a hard hat with adjustable headgear and a face shield with an antifog coating.

Fans—Fans (sold separately) mount on your hood and pumps air inside using a fan motor. They operate on four AA batteries (not included).

Protect your eyes the moment you start welding—four sensors detect the light and automatically darken the lens. Unlike traditional green welding lenses, these helmets use a true color lens to enhance clarity and color accuracy. They allow for a better look at your weld pool to increase weld quality and reduce eye strain. To customize the helmet’s fit so you can focus on welding, these helmets have a ratchet adjustment with an easy-turn knob. Solar cells recharge the helmet’s battery while you work.

Weld with the same quality as you would in bright conditions. These helmets have a built-in LED light that brightens your workspace, so you can see your weld and maintain precision even in dark areas. Turn the LED light on with the press of a button, and when it detects an arc or intense light, the light automatically turns off.

As you begin to weld, four arc sensors detect the light and automatically darken the lens. Unlike traditional green welding lenses, these helmets use a true color lens to enhance clarity and color accuracy. They have digital controls behind the lens where you can set the shade number, delay time, and sensitivity. To switch to grind mode without removing your helmet, use the button above the lens.

Shield your face and neck from flame and electrical hazards while working in the cold.

Keep cool while staying shielded from flame and electrical hazards.

Withstand flash fire for up to 8 seconds—the clothes in these kits can protect you for twice as long as most flame-resistant clothing. Made of rayon/aramid, the coveralls and mask absorb moisture to keep you cool and comfortable.

The coveralls have a 10 ft. Kevlar strap, so nearby teammates can pull you to safety without putting themselves at risk if there’s a fire. The reflective stripes keep you easy to see where there's low visibility. The zipper closure on the front is covered by a hook-and-loop flap so it doesn't scrape equipment or get hot. The legs have zippers on the sides as well, so you can fit them over bulky boots. Tighten the hook and loop straps on the bottom of the pants to keep flames out. The sleeves have cuffs with thumb holes to keep the sleeves in place and prevent flames from sneaking in. When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under the coveralls.

Take full control of your shade level with these helmets—you can set the lens to adjust in half-shade increments. They have digital controls behind the lens where you can set the shade number, delay time, and sensitivity. Save up to nine settings to quickly switch between tasks. To switch to grind mode without removing your helmet, press the button above the lens.

As you weld, four sensors detect the light and automatically darken the lens. To improve weld quality and reduce eye strain, these helmets have a wide panoramic view and a true color lens. The lens enhances clarity and color accuracy to reduce the color distortion of your view.

Solar cells recharge the helmet’s battery while you work.

Bib overalls have adjustable suspenders to modify the length.

When measuring chest size, measure around the fullest part of your chest. Find your waist size by measuring just above the top of your hip bone. Take all measurements over any clothing you expect to wear under these suits.

The fluorescent yellow fabric and reflective stripes on these sweatshirts make you stand out. They meet Class 3 ANSI/ISEA 107 standards for high-visibility clothing, so you’ll be seen from ¼ mile away. These sweatshirts also meet Category 3 NFPA 70E and NFPA 2112 for moderate protection against flames and electrical arc flashes. Made with a aramid/modacrylic blend, these sweatshirts are both durable and comfortable. To help prevent body heat from escaping, they have snug knit cuffs and a snug knit waistband. Keep your hands warm in the exterior pocket. They have an interior pocket for storage.

When choosing clothing to protect you from arc flashes, match the arc rated personal protective equipment (PPE) category required by your workplace.

Also known as pancake welding helmets, these helmets have a flat face so you can get close to your welds. They’re often used when welding pipes, but are also useful where a standard welding helmet would be too bulky. These helmets extend further on one side than a standard welding helmet does for increased face protection from UV light, sparks, and spatter. A balsa wood box mounted inside the helmet fits around your face and eyes to block all light, even when working outdoors. Sand the box for a customizable fit. Designed for all-day comfort, they’re made of lightweight carbon fiber and have an open back for plenty of airflow.

These helmets have a large viewing area for a clear view of your workspace. The instant you start to weld, the lens darkens. Solar cells recharge the helmet’s battery while you work.

Choose a helmet based on which hand you use to hold your torch—they’re designed to protect the side opposite your welding hand, where sparks are most likely to fly. This means that left-hand helmets extend further on the right while right-hand helmets extend further on the left.