The toughest bits available, these withstand the shock and twisting force of impact drivers.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

A retaining ring at the tip grips inside the recess to ensure screws won't slip off the bit.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

Ribs forged into the wings of these bits grip the screw recess to reduce stripping. They're also known as ACR® bits.

Drive screws with both ends of these bits. Use with hand drivers.

A wide tip makes good contact in shallow and coated screw recesses, such as those filled with paint.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

Remove screws in hard-to-reach places. A spring-loaded sleeve guides bits onto the screw head and keeps them from slipping out.

Bits have a different size at each end.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas.

Bits have a different size at each end.

Strong and durable, these multipurpose bits are for use with bit screwdrivers. They're designed for screws with a square recess in the head and are also known as Robertson bits.

An exterior stop collar prevents fasteners from being driven too deep. Use with soft materials such as drywall, wood, and fiberboard.

Protect your stainless steel screws by using a stainless steel bit. If steel flakes off a standard bit and into the recess, it can lead to rust and contamination. These bits eliminate that risk.

The toughest bits available, these withstand the shock and twisting force of impact drivers.

Ribs forged into the wings of these offset-cross-shaped bits grip the screw recess to reduce stripping. They are also known as ACR® bits.

These bits provide a secure grip on the Phillips/slotted combination-drive screws in electrical equipment.

An opening at the tip accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Bits have a different size at each end. An opening at the tips accommodates the pin in the recess of tamper-resistant Torx screws. These are also known as pin-in-Torx bits.

Turn two drive styles with one reversible bit. Remove and replace to change the tip.

An opening at the tip accommodates the pin in the recess of tamper-resistant Phillips screws. These are also known as pin-in-head Phillips bits.

Turn the screws found in Apple devices.

A three-winged tip fits triangular slotted screw recesses.

Grip the indentations on the head of tri-groove fasteners.

An opening at the tip accommodates the pin in the recess of tamper-resistant pentalobe and tamper-resistant Torx Plus screws.

The six rounded points fit the star-shaped recess of Torx-Plus screws. These bits have a similar profile to Torx but are not recommended for use with standard Torx screws.

Because they make contact on the flat sides of fasteners rather than only on the corners, these magnetic bits significantly reduce slipping and stripping. They’re also known as lobular bits.

Turn hex nuts and cap screws.

Less likely to crack or shatter under high torque than standard bits, these are often used with power tools to install machine screws.

The knurled shank on these bits allows finger tightening. They can also be used with the included screwdriver.

A retaining ring grips inside the recess to hold screws in place. These bits have a ball end that allows angled entry to drive screws in hard-to-reach areas.

A magnet holds the nut in place.

The slightly tapered tip wedges into the screw recess for a secure hold. These are also known as Torx-Align bits.

Grip the indentations on the head of tri-groove fasteners.

An opening at the tip accommodates the pin in the recess of tamper-resistant hex screws. These are also known as pin-in-hex or pin-in-socket bits.

A three-winged tip fits triangular slotted screw recesses.

Also known as Robertson bits these are designed for screws with a square recess in the head.

Lock your bit into the adapter to prevent accidental disengagement. These adapters hold hex-shank bits (also known as insert bits) in powered tools.

A magnetic ring at the end of the adapter holds flat-head screws in place to ensure good contact between the bit and screw. Use these adapters to hold hex-shank bits (also known as insert bits) in powered tools.

Bend these adapters up to 90° to access hard-to-reach fasteners. Use them to hold hex-shank bits (also known as insert bits) in powered tools.

Use a 4 mm bit in a bit driver that's designed for 1/4" bits.

Keep these caddies in your tool drawer or take them with you.

Mount the magnetic base to walls, cabinets, and other steel surfaces.