McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    26 Products

    Extreme-Temperature Refractory Cement

    Image of Product. Front orientation. Refractory Cement. Extreme-Temperature Refractory Cement.
    Set and repair cast iron and steel furnaces, heaters, stoves, and boilers with this ready-to-use cement. It experiences minimal shrinkage for a permanent smokeproof and gasproof joint. Apply with a trowel or a spatula. A minimum temperature of 212° F is required to harden. Cut hardened cement with a carbide-tipped saw.
    Container
    Size
    Type
    Approx. Coverage
    Area, ft²
    Cure Temp.,
    ° F
    Max. Temp.,
    ° F
    Density,
    lb/ft³
    Color
    Each
    8 fl. oz.Pail0.632122,500122Beige9372K8500000
    64 fl. oz.Pail52122,500122Beige9372K8600000
    1 gal.Pail102122,500122Beige9372K8700000

    High-Temperature Gasket Sealants

    Image of Product. Front orientation. Gasket Sealants. High-Temperature Gasket Sealants, Cartridge.
    Image of Product. Front orientation. Gasket Sealants. High-Temperature Gasket Sealants, Tube.

    Cartridge

    Tube

    Even in high temperatures, these sealants maintain their strength.
    Container
    Size, fl.
    oz.
    Type
    Begins to
    Harden, min.
    Reaches Full
    Strength, hr.
    Max. Temp.,
    ° F
    Color
    For Use On
    Each
    2.3Tube30242,000BlackCast Iron, Fiberglass, Steel7573A2900000
    2.3Tube6032,000BlackAluminum, Brass, Bronze, Cast Iron, Copper, Fiberglass, Masonry, Stainless Steel, Steel, Titanium7573A6300000
    10.3Cartridge30242,000BlackCast Iron, Fiberglass, Steel7573A3100000
    10.3Cartridge6032,000BlackAluminum, Brass, Bronze, Cast Iron, Copper, Fiberglass, Masonry, Stainless Steel, Steel, Titanium7573A6500000
     

    Firebrick Bonding Mortar

    Image of Product. Front orientation. Refractory Cement. Firebrick Bonding Mortar.
    Lay, coat, and bond firebricks. Apply this mortar with a trowel. One pail sets approximately 40 bricks.
    Container
    Net Wt., lb.
    Container
    Type
    Approx. Brick
    Coverage
    Max. Temp.,
    ° F
    Density,
    lb/ft³
    Color
    Each
    15Pail403,000129Gray9368K6000000

    High-Temperature Surface Fillers

    Image of Product. Front orientation. Surface Fillers. High-Temperature Surface Fillers, Ceramic, Pail.
    Image of Product. Front orientation. Surface Fillers. High-Temperature Surface Fillers, Ceramic, Cartridge.
    Image of Product. Front orientation. Surface Fillers. High-Temperature Surface Fillers, Ceramic, Syringe.

    Ceramic

    Pail

    Ceramic

    Cartridge

    Ceramic

    Syringe

    Able to withstand temperatures up to 2300° F, these ceramic surface fillers are often used as thermal insulation on brick, mortar, burner blocks, furnace holders, and thermocouples.
    Container
    Temp.
    Range
    Size
    Type
    Begins to
    Harden, min.
    Reaches Full
    Strength, hr.
    Consistency
    Mixing
    Req.
    Approx. Coverage
    @ Thk.
    Max.
    Thk.
    For Use
    Outdoors
    Min.
    Max.,
    ° F
    Color
    For Use On
    Each
    Ceramic Surface Fillers
    4 fl. oz.Syringe208PuttyNo20 in² @ 1/4"Not RatedNoNot Rated2,300WhiteCeramic, Masonry7551A23000000
    11 fl. oz.Cartridge208PuttyNo60 in² @ 1/4"Not RatedNoNot Rated2,300WhiteCeramic, Masonry7551A2400000
    1 gal.Pail208PuttyNo720 in² @ 1/4"Not RatedNoNot Rated2,300WhiteCeramic, Masonry7551A26000000
     

    Firebrick Repair Coatings

    Image of Product. Front orientation. Firebrick Repair Coatings.
    Renew heat resistance and performance of worn firebrick. Apply coating with a brush or spray on for a crack-free seal.
    Container
    Size, gal.
    Approx. Coverage
    Area, ft²
    Temp. Range,
    ° F
    Density,
    lb/ft³
    Color
    Each
    193-50 to 2,350100Beige9366K50000000

    Fire-Stop Cement

    Image of ProductInUse. Front orientation. Fire Stops. Fire-Stop Cement.
    Image of Product. Front orientation. Fire Stops. Fire-Stop Cement, Pail.
    Image of Product. Front orientation. Fire Stops. Fire-Stop Cement, Bag.

    Pail

    Bag

    Seal openings in fire-resistant floors and walls to stop the spread of smoke and flames. Often used to fill gaps around pipes or conduit, this cement forms a rigid, tight-fitting shield. It’s heavier and messier to apply than fire-stop blocks or sheets, but it's an economical choice for covering a large area.
    This cement comes as a powder—mix in water until you reach the consistency you need. The thicker the cement, the better it will stick to walls; thinner cement dries with a smoother finish on floors.
    Pail—Cement in a pail is best for small, infrequent jobs. The pail is resealable and has a carrying handle.
    Paintable—You can also paint over this cement once it dries.
    Container
    Size,
    gal.
    Net Wt.,
    lb.
    Type
    Color
    Application
    Temp., ° F
    Fire-Stop
    Application
    Fire Safety
    Rating
    Flammability
    Rating
    Specs. Met
    Performance
    Each
    —45BagLight Red40 to 120Through Penetration4 hr.UL 1479
    		ASTM E814, ULC-S115Paintable93355K230000000
    528PailWhite40 to 120Through Penetration3 hr.UL 1479
    		ASTM E814, ULC-S115Paintable93355K25000000
     

    High-Temperature Contact Adhesives

    Image of Product. Front orientation. Contact Adhesives. High-Temperature Contact Adhesives.
    These adhesives resist temperatures up to 500° F, as well as chemicals, fuels, grease, and water. Apply them to both surfaces, air dry, and then bring together to bond. Heat to 300° F to reach full strength.
    Cannot Be Sold To—These adhesives cannot be sold to the regions listed because they exceed local regulatory limits on VOCs (volatile organic compounds).
    Container
    Mfr. Model
    No.
    Size
    Type
    Begins to
    Harden, min.
    Reaches Full
    Strength, min.
    Heating Req. to Reach
    Full Strength
    Shear Strength,
    psi
    Cure Type
    Consistency
    Viscosity,
    cP
    Temp. Range,
    ° F
    Color
    For Joining
    Cannot Be Sold To
    Each
    Pliobond
    HT-3032 fl. oz.Can33030 Min. @ 300°F1,450Heat, Room TemperatureThick Liquid6,500-40 to 500BeigeCeramic, MetalAlexandria, VA; Arlington County, VA; Connecticut; Delaware; District of Columbia; Fairfax County, VA; Fairfax, VA; Falls Church, VA; Los Angeles County, CA; Loudoun County, VA; Maine; Manassas Park, VA; Manassas, VA; Maryland; Massachusetts; New Jersey; New York; Orange County, CA; Pennsylvania; Prince William County, VA; Rhode Island; Riverside County, CA; San Bernardino County, CA; Stafford County, VA; Utah; Vermont7468A3000000
    HT-301 gal.Can33030 Min. @ 300°F1,450Heat, Room TemperatureThick Liquid6,500-40 to 500BeigeCeramic, MetalAlexandria, VA; Arlington County, VA; Connecticut; Delaware; District of Columbia; Fairfax County, VA; Fairfax, VA; Falls Church, VA; Los Angeles County, CA; Loudoun County, VA; Maine; Manassas Park, VA; Manassas, VA; Maryland; Massachusetts; New Jersey; New York; Orange County, CA; Pennsylvania; Prince William County, VA; Rhode Island; Riverside County, CA; San Bernardino County, CA; Stafford County, VA; Utah; Vermont7468A4000000
     

    High-Temperature Surface Fillers for Metal

    Image of Product. Front orientation. Surface Fillers. High-Temperature Surface Fillers for Metal, Epoxy, Syringe.
    Image of Product. Front orientation. Surface Fillers. High-Temperature Surface Fillers for Metal, Epoxy, Stick.

    Epoxy

    Syringe

    Epoxy

    Stick

    Image of Product. Front orientation. Surface Fillers. High-Temperature Surface Fillers for Metal, Epoxy, Can, Bottle.

    Epoxy

    Can, Bottle

    Repair and rebuild metal surfaces that are exposed to heat. These surface fillers withstand temperatures over 450° F. Fillers that have a mix ratio are multi-part fillers. The size listed is the combined total of the parts.
    Syringe—Surface fillers in a syringe come with everything you need to make repairs.
    Stick—Surface fillers in a stick have a resin on the outside and a hardener on the inside. Cut the desired amount from the sticks, knead to a uniform color to mix, and press into place.
    Container
    Temp.
    Range, ° F
    Size, fl.
    oz.
    Net Wt.,
    oz.
    Type
    Lg.
    Begins to
    Harden
    Reaches Full
    Strength, hr.
    Heating Req. to Reach
    Full Strength
    Consistency
    Mixing
    Req.
    Mix
    Ratio
    Approx. Coverage
    @ Thk.
    Max.
    Thk.
    Dia.
    For Use
    Outdoors
    Min.
    Max.
    Color
    Process After
    Hardening
    For Use On
    Each
    Epoxy Surface Fillers
    —4Stick8"90 min.72—PuttyYes—16 in² @ 1/4"1/2"1"Yes-40450GoldDrill, Sand, TapAluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium7803A21000000
    1.5—Syringe—20 min.24—PuttyYes9.1:11 in² @ 1/4"Not Rated—Yes-40500GrayMachine, Drill, SawAluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Fiberglass75325A100000
    16—Can, Bottle—20 min.24—PuttyYes9.1:110 in² @ 1/4"Not Rated—YesNot Rated500GrayMachine, Drill, SawAluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Fiberglass75325A200000
     
    Ceramic Surface Fillers
    8—Can—5 hr.62 Hrs. Air Dry Then 4 Hrs. @ 200°FPuttyNo—32 in² @ 1/4"3/8"—NoNot Rated2,000Dark GraySandSteel, Stainless Steel, Cast Iron7356A3300000
    12—Can, Bottle—2 hr.64 Hrs. Air Dry Then 2 Hrs. @ 160°FPuttyYes2:148 in² @ 1/4"3/8"—NoNot Rated1,400Light GraySandAluminum
    		7356A3200000
    16—Bottle—5 hr.62 Hrs. Air Dry Then 4 Hrs. @ 200°FPuttyNo—65 in² @ 1/4"3/8"—NoNot Rated2,000Dark GraySandSteel, Stainless Steel, Cast Iron7356A35000000
    24—Can—2 hr.64 Hrs. Air Dry Then 2 Hrs. @ 160°FPuttyYes2:196 in² @ 1/4"3/8"—NoNot Rated1,400Light GraySandAluminum
    		7356A34000000
     

    Fine-Particle Abrasion-Resistant Surface Fillers for Metal

    Image of Product. Front orientation. Surface Fillers. Fine-Particle Abrasion-Resistant Surface Fillers for Metal, Epoxy, Jar.

    Epoxy

    Jar

    For use in processing equipment that carries particles smaller than 1/16" in diameter, these ceramic-filled epoxies rebuild and repair surfaces exposed to abrasion from particles, such as dust collectors, fan blades, and fan housings. The size listed is the combined total of the two parts.
    Material Certificate Icon
    Certificates with a traceable lot number and product shelf life are available for these products. Download certificates from ORDER HISTORY after your order ships.
    Container
    Temp.
    Range, ° F
    Mfr. Model
    No.
    Net Wt.,
    lb.
    Type
    Begins to
    Harden, min.
    Reaches Full
    Strength, hr.
    Consistency
    Mixing
    Req.
    Mix
    Ratio
    Approx. Coverage
    @ Thk.
    Max.
    Thk.
    For Use
    Outdoors
    Min.
    Max.
    Color
    Process After
    Hardening
    For Use On
    Each
    Loctite® Fixmaster Wear Resistant Putty
    PC 72221Jar3024PuttyYes2:150 in² @ 1/4"1"Yes-20220GraySandAluminum, Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium7489A330000000
     

    Fuel-Resistant Surface Fillers

    Image of Product. Front orientation. Surface Fillers. Fuel-Resistant Surface Fillers.
    Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.
    1.5 pt. Container—1.5-pint container can treat a 10-gallon fuel tank.
    3 pt. Container—3-pint container can treat a 20-gallon fuel tank.
    Container
    Temp.
    Range, ° F
    Size,
    pt.
    Type
    Begins to
    Harden, min.
    Reaches Full
    Strength, hr.
    Consistency
    Mixing
    Req.
    Mix
    Ratio
    For Use
    Outdoors
    Min.
    Max.
    Color
    Process After
    Hardening
    For Use On
    Each
    Epoxy Surface Fillers
    1.5Can524Thick LiquidYes2:1No7090AmberDrill, Sand, TapAcrylic Plastic, Aluminum, Brass, Bronze, Copper, Vinyl Plastic, Galvanized Iron, Galvanized Steel, Silver, Steel, Stainless Steel, Cast Iron, Titanium, ABS, CPVC, PETG, Polycarbonate, Nylon, Polyethylene, Polypropylene, Polyimide, PVC, PVDF, Ceramic, Porcelain, Fiberglass2450N12000000
    3Can524Thick LiquidYes2:1No7090AmberDrill, Sand, TapAcrylic Plastic, Aluminum, Brass, Bronze, Copper, Vinyl Plastic, Galvanized Iron, Galvanized Steel, Silver, Steel, Stainless Steel, Cast Iron, Titanium, ABS, CPVC, PETG, Polycarbonate, Nylon, Polyethylene, Polypropylene, Polyimide, PVC, PVDF, Ceramic, Porcelain, Fiberglass2450N11000000
     
    back to top