About Rod Ends
More
About Hinges
More
Surface-Mount Hinges with Holes
Hinges with a nonremovable pin deter tampering.
304 and 430 stainless steel hinges are more corrosion resistant than zinc. They also have good chemical resistance.
For technical drawings and 3-D models, click on a part number.
Door Leaf | Frame Leaf | Nonremovable Pin | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. | Wd. | Ht. | Wd. | O'all Wd. | Leaf Thick. | Range of Motion | Pin Dia. | Pin Material | Mounting Fasteners Included | No. of Mounting Holes | Mounting Screw Size  | Each | |
304 Stainless Steel—Polished | |||||||||||||
| 1 1/2" | 5/8" | 1 1/2" | 5/8" | 1 1/4" | 0.060" | 180° | 1/8" | 304 Stainless Steel | No | 4 | No. 8 | 0000000 | 00000 |
Narrow-Profile Lift-Off Hinges with Holes
These hinges are the right size for tight spaces and narrow frames. The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin. Mounting screws (not included) are concealed when the hinge is closed.
Hinges for inset doors are for doors that are flush with their frame when the door is closed. Capacity is per hinge. To choose a door mounting location, stand on the pull side of the door—use a right-side hinge if the hinge is on the right or a left-side hinge if it’s on the left.
For technical drawings and 3-D models, click on a part number.
Door Leaf | Frame Leaf | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. | Wd. | Ht. | Wd. | O'all Wd. | Leaf Thick. | Range of Motion | Capacity, lbs. | Pin Dia. | Mounting Fasteners Included | No. of Mounting Holes | Mounting Screw Size | Each | ||
Left Side Door Mounting Location | ||||||||||||||
For Inset Door—Standard | ||||||||||||||
Black Painted Zinc | ||||||||||||||
| 4 | 2 1/2" | 1 1/4" | 1 1/4" | 9/16" | 1 1/4" | 0.688" | 180° | 300 | 3/8" | No | 4 | No. 10 | 00000000 | 000000 |
Right Side Door Mounting Location | ||||||||||||||
For Inset Door—Standard | ||||||||||||||
Black Painted Zinc | ||||||||||||||
| 4 | 2 1/2" | 1 1/4" | 1 1/4" | 9/16" | 1 1/4" | 0.688" | 180° | 300 | 3/8" | No | 4 | No. 10 | 00000000 | 00000 |
Self-Closing Spring Hinges with Holes
Springs in these hinges automatically swing doors and gates closed behind you. All hinges have a nonremovable pin to deter tampering.
Zinc-plated low-carbon steel hinges have mild corrosion resistance.
304 stainless steel hinges are more corrosion resistant than zinc-plated low-carbon steel. They also have good chemical resistance.
For technical drawings and 3-D models, click on a part number.
Door Leaf | Frame Leaf | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. | Wd. | Ht. | Wd. | O'all Wd. | Leaf Thick. | Range of Motion | Pin Dia. | Pin Material | Mounting Fasteners Included | No. of Mounting Holes | Mounting Hole Style | Mounting Screw Size | Each | |
Zinc-Plated Low-Carbon Steel—Polished | ||||||||||||||
| 2 3/16" | 5/8" | 2 3/16" | 5/8" | 1 1/4" | 0.050" | 260° | 1/8" | Steel | No | 4 | Straight | No. 10 | 000000000 | 00000 |
304 Stainless Steel—Dull | ||||||||||||||
| 2 3/16" | 5/8" | 2 3/16" | 5/8" | 1 1/4" | 0.050" | 260° | 1/8" | 304 Stainless Steel | No | 4 | Straight | No. 8 | 000000000 | 0000 |
| 2 3/16" | 5/8" | 2 3/16" | 5/8" | 1 1/4" | 0.050" | 260° | 1/8" | 304 Stainless Steel | No | 4 | Straight | No. 10 | 000000000 | 0000 |
Self-Closing Spring Hinges without Holes
Springs in these hinges automatically swing doors and gates closed behind you. All hinges have a nonremovable pin to deter tampering.
304 stainless steel hinges are more corrosion resistant than low-carbon steel. They also have good chemical resistance.
For technical drawings and 3-D models, click on a part number.
Pull-Release Quick-Disconnect Hinges with Holes
These hinges are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back. The hinges can also be used as a latch on cabinet lids, electrical enclosure doors, and computer equipment housings. Pin travel is the distance the pin must be moved to disconnect the hinge. A pair includes one left-side and one right-side hinge.
300 series stainless steel hinges are more corrosion resistant than zinc-plated low-carbon steel. They also have good chemical resistance.
For technical drawings and 3-D models, click on a part number.
Door Leaf | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Ht. | Wd. | O'all Wd. | Leaf Thick. | Range of Motion | Pin Dia. | Pin Travel | Pin Material | Spring Material | Mounting Fasteners Included | No. of Mounting Holes | Mounting Hole Style | Mounting Screw Size | Pair | |
Zinc-Plated Low-Carbon Steel—Dull | ||||||||||||||
| 3" | 1 1/4" | 1 1/4" | 0.187" | 270° | 1/2" | 1 1/2" | Steel | Stainless Steel | No | 4 | Straight | 5/16" | 0000000 | 000000 |
300 Series Stainless Steel—Dull | ||||||||||||||
| 3" | 1 1/4" | 1 1/4" | 0.187" | 270° | 1/2" | 1 1/2" | 300 Series Stainless Steel | Stainless Steel | No | 4 | Straight | 5/16" | 0000000 | 00000 |
Piano Hinges without Holes
Longer than other hinges, piano hinges run the entire length of doors and lids for strength and durability. These hinges have a standard clearance—when they are closed, the distance between the leaves is about the same as the pin diameter.
Zinc-plated low-carbon steel and brass hinges have mild corrosion resistance.
304 stainless steel hinges are more corrosion resistant than zinc-plated low-carbon steel and brass. They also have good chemical resistance.
316 stainless steel hinges have excellent resistance to chemicals and salt water.
Aluminum hinges are about half the weight of low-carbon steel and brass. They have mild corrosion resistance.
Note: Prices are 15% to 20% lower when you buy 10 or more hinges of the same size.
For technical drawings and 3-D models, click on a part number.
Between
Hinge Leaves
Knuckle | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Pin Material | Lg. | Dia. | Range of Motion | 1 ft. | 2 ft. | 3 ft. | 4 ft. | 5 ft. | 6 ft. | 7 ft. | 8 ft. | |
0.035" Leaf Thick. | ||||||||||||||
| 1 1/4" | 5/64" | Steel | 1/4" | 0.148" | 270° | 000000000 | ||||||||
0.04" Leaf Thick. | ||||||||||||||
| 1 1/4" | 3/32" | Steel | 1/2" | 0.174" | 270° | 000000000 | ||||||||
0.05" Leaf Thick. | ||||||||||||||
| 1 1/4" | 1/8" | Steel | 1/2" | 0.225" | 270° | 000000000 | ||||||||
0.06" Leaf Thick. | ||||||||||||||
| 1 1/4" | 1/8" | Steel | 1/2" | 0.245" | 270° | 000000000 | ||||||||
Between
Hinge Leaves
Knuckle | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Pin Material | Lg. | Dia. | Range of Motion | 1 ft. | 2 ft. | 3 ft. | 4 ft. | 5 ft. | 6 ft. | 7 ft. | 8 ft. | |
0.035" Leaf Thick. | ||||||||||||||
| 1 1/4" | 3/32" | 304 Stainless Steel | 1/4" | 0.164" | 270° | 00000000 | ||||||||
0.04" Leaf Thick. | ||||||||||||||
| 1 1/4" | 3/32" | 304 Stainless Steel | 1/2" | 0.174" | 270° | 00000000 | ||||||||
0.05" Leaf Thick. | ||||||||||||||
| 1 1/4" | 1/8" | 304 Stainless Steel | 1/2" | 0.225" | 270° | 00000000 | ||||||||
0.06" Leaf Thick. | ||||||||||||||
| 1 1/4" | 1/8" | 304 Stainless Steel | 1/2" | 0.245" | 270° | 00000000 | ||||||||
Between
Hinge Leaves
Knuckle | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Material | Pin Material | Lg. | Dia. | Range of Motion | 1 ft. | 2 ft. | 3 ft. | 4 ft. | 5 ft. | 6 ft. | 7 ft. | 8 ft. | |
0.032" Leaf Thick. | |||||||||||||||
| 1 1/4" | 3/32" | 3004 Aluminum | 3004 Aluminum | 1/4" | 0.158" | 270° | 00000000 | ||||||||
0.04" Leaf Thick. | |||||||||||||||
| 1 1/4" | 3/32" | 5052 Aluminum | 5052 Aluminum | 1/2" | 0.174" | 270° | 00000000 | ||||||||
0.05" Leaf Thick. | |||||||||||||||
| 1 1/4" | 1/8" | 5052 Aluminum | 5052 Aluminum | 1/2" | 0.225" | 270° | 00000000 | ||||||||
0.06" Leaf Thick. | |||||||||||||||
| 1 1/4" | 1/8" | 5052 Aluminum | 5052 Aluminum | 1/2" | 0.245" | 270° | 00000000 | ||||||||
Mil. Spec. Piano Hinges without Holes
Choose these hinges for their adherence to strict military standards for material and construction. Longer than other hinges, piano hinges run the entire length of doors and lids for strength and durability. All of these hinges have a standard clearance—when they are closed, the distance between the leaves is about the same as the pin diameter.
302 stainless steel hinges are more corrosion resistant than aluminum. They also have good chemical resistance.
Aluminum hinges are about half the weight of steel. They have mild corrosion resistance.
Note: Prices are 15% to 20% lower when you buy 10 or more hinges of the same size.
For technical drawings and 3-D models, click on a part number.
Piano Hinges with Holes
Longer than other hinges, piano hinges run the entire length of doors and lids for strength and durability. These hinges have a standard clearance—when they are closed, the distance between the leaves is about the same as the pin diameter.
Brass as well as zinc-, brass-, bronze-, chrome-, and nickel-plated low-carbon steel hinges have better corrosion resistance than painted and primed low-carbon steel.
304 stainless steel hinges are more corrosion resistant than brass as well as zinc-, brass-, bronze-, chrome-, and nickel-plated low-carbon steel. They also have good chemical resistance.
316 stainless steel hinges have excellent resistance to chemicals and salt water.
Aluminum hinges are about half the weight of brass and low-carbon steel. They have mild corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Between
Hinge Leaves
Between
Hinge Leaves
Between
Hinge Leaves
Between
Hinge Leaves
Between
Hinge Leaves
Knuckle | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Pin Material | Lg. | Dia. | Range of Motion | Mounting Fasteners Included | Mounting Screw Size | For Mounting Screw Countersink Angle | Each | |
4 ft. | ||||||||||
0.04" Leaf Thick. | ||||||||||
| 1 1/4" | 3/32" | Steel | 1/2" | 0.174" | 270° | No | No. 4 | 82° | 00000000 | 000000 |
0.06" Leaf Thick. | ||||||||||
| 1 1/4" | 1/8" | Steel | 1/2" | 0.245" | 270° | No | No. 6 | 82° | 000000 | 00000 |
6 ft. | ||||||||||
0.04" Leaf Thick. | ||||||||||
| 1 1/4" | 3/32" | Steel | 1/2" | 0.174" | 270° | No | No. 4 | 82° | 00000000 | 00000 |
0.06" Leaf Thick. | ||||||||||
| 1 1/4" | 1/8" | Steel | 1/2" | 0.245" | 270° | No | No. 6 | 82° | 00000000 | 00000 |
Between
Hinge Leaves
Between
Hinge Leaves
Knuckle | 1 ft. | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Pin Material | Lg. | Dia. | Range of Motion | Mounting Fasteners Included | Mounting Screw Size | For Mounting Screw Countersink Angle | |
0.06" Leaf Thick. | |||||||||
| 1 1/4" | 1/8" | Steel | 1/2" | 0.245" | 270° | No | No. 6 | 82° | 00000000 |
Between
Hinge Leaves
Knuckle | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Pin Material | Lg. | Dia. | Range of Motion | Mounting Fasteners Included | Mounting Screw Size | For Mounting Screw Countersink Angle | 1 ft. | 3 ft. | 4 ft. | 6 ft. | 8 ft. | |
0.042" Leaf Thick. | ||||||||||||||
| 1 1/4" | 3/32" | 304 Stainless Steel | 1/2" | 0.178" | 270° | No | No. 4 | 82° | 0000000 | |||||
0.06" Leaf Thick. | ||||||||||||||
| 1 1/4" | 1/8" | 304 Stainless Steel | 1/2" | 0.245" | 270° | No | No. 6 | 82° | 0000000 | |||||
Between
Hinge Leaves
Between
Hinge Leaves
Knuckle | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Pin Material | Lg. | Dia. | Range of Motion | Mounting Fasteners Included | Mounting Screw Size | For Mounting Screw Countersink Angle | 1 ft. | 3 ft. | 6 ft. | |
0.04" Leaf Thick. | ||||||||||||
| 1 1/4" | 3/32" | 316 Stainless Steel | 1/2" | 0.174" | 270° | No | No. 5 | 82° | 0000000 | |||
0.06" Leaf Thick. | ||||||||||||
| 1 1/4" | 1/8" | 316 Stainless Steel | 1/2" | 0.245" | 270° | No | No. 6 | 82° | 0000000 | |||
Between
Hinge Leaves
Knuckle | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| O'all Wd. | Pin Dia. | Pin Material | Lg. | Dia. | Range of Motion | Mounting Fasteners Included | Mounting Screw Size | For Mounting Screw Countersink Angle | 1 ft. | 3 ft. | 6 ft. | |
0.04" Leaf Thick. | ||||||||||||
| 1 1/4" | 3/32" | 316 Stainless Steel | 1/2" | 0.174" | 270° | No | No. 5 | 82° | 0000000 | |||
0.06" Leaf Thick. | ||||||||||||
| 1 1/4" | 1/8" | 316 Stainless Steel | 1/2" | 0.245" | 270° | No | No. 6 | 82° | 0000000 | |||
Slip-On Piano Hinges
Between
Hinge Leaves
No need for drilling holes or welding, slip these hinges onto panel and door edges for a secure fit. Longer than other hinges, piano hinges run the entire length of doors and lids for strength and durability. All of these hinges are pinless—they have a flexible joint instead of a pin. They also have a standard clearance—when they are closed, the distance between the leaves is about half the width of the flexible joint.
Acrylic and PETG hinges have good corrosion and chemical resistance. PETG has better clarity than acrylic.
For technical drawings and 3-D models, click on a part number.
| For Panel Thick. | Leaf Thick. | O'all Wd. | Lg., ft. | Range of Motion | Center Color | Temp. Range, °F | Color | Each | |
PETG Plastic | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 1/4" | 0.050" | 1 1/4" | 6 | 180° | Clear | 45° to 100° | Clear | 00000000 | 000000 |
Corrosion-Resistant Partially Threaded Rod End Bolts
Pivot and hinge components in wet and corrosive environments with these stainless steel or brass rod end bolts. They're commonly known as swing bolts and eyebolts. With no moving parts, they're less likely to wear out than ball joint rod ends, although they don't compensate for misalignment as effectively. Use them to guide and connect components, such as tubing, or as a turnbuckle to tension wire and cable. They can also be used as tie downs and hinges.
With external threads, these bolts hold fast to female threaded components in applications where high shear strength is required, such as water pumps, alternators, and motor mounts. Because the shank is only partially threaded, they handle a greater amount of force from the side than bolts with a fully threaded shank.
303 and 304 stainless steel rod end bolts won't rust in humid, wet, and washdown environments. They're stronger than brass bolts and nearly as strong as steel. They will rust when exposed to salt water and chemicals, however. 316 stainless steel rod end bolts are our most corrosion resistant, and they're nearly as strong as steel rod end bolts. Use them in areas with salt water, chlorine, and chemicals without worrying about rust.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | O'all Wd. | Shank Center Lg. | Shank Thread Lg. | O'all Thick. | Tensile Strength, psi | Each | |
Right-Hand Threaded Shank | ||||||||
|---|---|---|---|---|---|---|---|---|
304 Stainless Steel | ||||||||
| 5/8"-11 | 5/8" | 1 1/4" | 4 1/2" | 2" | 11/16" | 85,000 | 0000000 | 000000 |
| 5/8"-11 | 5/8" | 1 1/4" | 5" | 1 3/4" | 11/16" | 85,000 | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 6" | 1 3/4" | 11/16" | 85,000 | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 6" | 2 1/2" | 11/16" | 85,000 | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 7" | 1 3/4" | 11/16" | 85,000 | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 8" | 1 3/4" | 11/16" | 85,000 | 0000000 | 00000 |
316 Stainless Steel | ||||||||
| 5/8"-11 | 5/8" | 1 1/4" | 4 1/2" | 2" | 11/16" | 80,000 | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 5" | 1 3/4" | 11/16" | 80,000 | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 6" | 1 3/4" | 11/16" | 80,000 | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 6" | 2 1/2" | 11/16" | 80,000 | 0000000 | 00000 |
Partially Threaded Rod End Bolts
Create pivoting connections in applications that require high shear strength—the partially threaded shank of these rod end bolts withstands more side force than a fully threaded shank. Also known as swing bolts and eyebolts, they are used to create hinges, turnbuckles, and tie downs. Unlike ball joint rod ends, these rod end bolts are made from a single piece of metal, so they wear down more slowly and have a more controlled swing. However, because they do not have a moving ball joint, they do not compensate for angular misalignment.
Made from steel, they are stronger and more wear resistant than stainless steel rod end bolts, but they are not as corrosion resistant. Rod end bolts with a black-oxide finish have a dark, matte coating that keeps the steel from rusting in dry environments.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | O'all Wd. | Shank Center Lg. | Shank Thread Lg. | O'all Thick. | Tensile Strength, psi | Material | Each | |
Right-Hand Threaded Shank | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 5/8"-11 | 5/8" | 1 1/4" | 4 1/2" | 2" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 000000 |
| 5/8"-11 | 5/8" | 1 1/4" | 5" | 1 3/4" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 6" | 1 3/4" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 6" | 2 1/2" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 7" | 1 3/4" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 8" | 1 3/4" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
Left-Hand Threaded Shank | |||||||||
| 5/8"-11 | 5/8" | 1 1/4" | 4 1/2" | 2" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 5" | 1 3/4" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
| 5/8"-11 | 5/8" | 1 1/4" | 6" | 2 1/2" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 00000 |
Internally Threaded Rod End Bolts with Partial Threads
Also known as swing bolts and eyebolts, rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | O'all Wd. | Shank Center Lg. | Shank Thread Lg. | O'all Thick. | Tensile Strength, psi | Material | Each | |
Right-Hand Threaded Shank | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 5/8"-11 | 5/8" | 1 1/4" | 4 1/2" | 1" | 11/16" | 75,000 | Black-Oxide Carbon Steel | 0000000 | 000000 |
Corrosion-Resistant Flat-Shoulder Rod End Bolts
Made of stainless steel, these rod end bolts are stronger and more corrosion resistant than our standard flat-shoulder rod end bolts. Also known as jig latch bolts, they mount flush to any flat surface.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | O'all Wd. | Shank Center Lg. | Shank Thread Lg. | Shank Threading | O'all Thick. | Tensile Strength, psi | Material | Each | |
Right-Hand Threaded Shank | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 5/8"-11 | 5/8" | 1 1/4" | 3 1/2" | 1 5/8" | Partially Threaded | 3/4" | 100,000 | 303 Stainless Steel | 0000000 | 000000 |
| 5/8"-11 | 5/8" | 1 1/4" | 4 3/4" | 2 1/2" | Partially Threaded | 3/4" | 100,000 | 303 Stainless Steel | 0000000 | 00000 |
Flat-Shoulder Rod End Bolts
These black-oxide carbon steel rod end bolts are heat treated for added strength. Also known as jig latch bolts, they mount flush to any flat surface.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | O'all Wd. | Shank Center Lg. | Shank Thread Lg. | Shank Threading | O'all Thick. | Tensile Strength, psi | Material | Each | |
Right-Hand Threaded Shank | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 5/8"-11 | 5/8" | 1 1/4" | 3 1/2" | 1 5/8" | Partially Threaded | 3/4" | 78,000 | Black-Oxide Carbon Steel | 00000000 | 000000 |
| 5/8"-11 | 5/8" | 1 1/4" | 4 3/4" | 2 1/2" | Partially Threaded | 3/4" | 78,000 | Black-Oxide Carbon Steel | 00000000 | 00000 |
Corrosion-Resistant Rod End Bolt Blanks
Made of stainless steel, these rod end bolts are more corrosion resistant than steel rod end bolts. Cut, tap, bore, or weld them to your exact requirements. They have an unfinished shank.
304 stainless steel rod end bolts offer good corrosion resistance. 316 stainless steel rod end bolts offer excellent corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Rod End Bolt Blanks
Cut, tap, bore, or weld these rod end bolts to your exact requirements. They have an unfinished shank.
For technical drawings and 3-D models, click on a part number.
| Shank Dia. | O'all Wd. | Shank Center Lg. | O'all Thick. | Tensile Strength, psi | Material | Features | Each | |
| 5/8" | 1 1/4" | 3" | 11/16" | 75,000 | Carbon Steel | Centered Starter Dimple | 00000000 | 00000 |
| 5/8" | 1 1/4" | 5 1/8" | 11/16" | 75,000 | Carbon Steel | Centered Starter Dimple | 00000000 | 00000 |
| 5/8" | 1 1/4" | 5 1/2" | 11/16" | 75,000 | Carbon Steel | Centered Starter Dimple | 00000000 | 00000 |
| 5/8" | 1 1/4" | 6 1/2" | 11/16" | 75,000 | Carbon Steel | Centered Starter Dimple | 00000000 | 00000 |
| 5/8" | 1 1/4" | 8" | 11/16" | 75,000 | Carbon Steel | Centered Starter Dimple | 00000000 | 00000 |
| 5/8" | 1 1/4" | 12" | 11/16" | 75,000 | Carbon Steel | Centered Starter Dimple | 00000000 | 00000 |
High-Strength Rod End Bolt Blanks
These alloy steel bolts have the highest tensile strength of any blank rod end bolt we offer. Cut, tap, bore, or weld them to your exact requirements. They have an unfinished shank.
For technical drawings and 3-D models, click on a part number.
| Shank Dia. | O'all Wd. | Shank Center Lg. | O'all Thick. | Tensile Strength, psi | Material | Features | Each | |
| 5/8" | 1 1/4" | 3 1/2" | 11/16" | 125,000 | Alloy Steel | Centered Starter Dimple | 00000000 | 000000 |
| 5/8" | 1 1/4" | 6" | 11/16" | 125,000 | Alloy Steel | Centered Starter Dimple | 00000000 | 00000 |
| 5/8" | 1 1/4" | 12" | 11/16" | 125,000 | Alloy Steel | Centered Starter Dimple | 00000000 | 00000 |
Internally Threaded Thrust-Rated Ball Joint Rod Ends
An innovative body design keeps the ball from being pushed out when supporting thrust loads. Rod ends are zinc-plated steel for moderate corrosion resistance and have a self-lubricating polyurethane insert.
For technical drawings and 3-D models, click on a part number.
Static Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Radial | Thrust | Temp. Range, °F | Material | Choose a Shank Thread Direction | Each | |
| 1/2"-20 | 1/2" | 30° | 1 1/4" | 5/8" | 2" | 1" | 5,900 | 2,110 | -40° to 175° | Zinc-Plated Carbon Steel | 0000000 | 000000 | |
Thrust-Rated Ball Joint Rod Ends
An innovative body design keeps the ball from being pushed out when supporting thrust loads. Rod ends are zinc-plated steel for moderate corrosion resistance and have a self-lubricating polyurethane insert.
For technical drawings and 3-D models, click on a part number.
Static Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Radial | Thrust | Temp. Range, °F | Material | Choose a Shank Thread Direction | Each | |
| 1/2"-20 | 1/2" | 28° | 1 1/4" | 5/8" | 2 7/16" | 1 1/2" | 5,900 | 2,110 | -40° to 175° | Zinc-Plated Carbon Steel | 0000000 | 000000 | |
High-Speed Ball Bearing Rod Ends
A double row of precision ball bearings allows high speeds and smooth operation. Rod ends are made of cadmium- or zinc-plated steel, which both offer moderate corrosion resistance. Seals keep lubricant in and dirt out.
Cadmium-plated steel rod ends have lubricant that meets MIL-PRF-81322. Those with an oversized shank have a shank that is one size larger than the ID to handle greater stress.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Max. Ball Swivel | O'all Wd. | O'all Thick. | Shank Center Lg. | Shank Thread Lg. | Static Radial Load Cap., lbs. | Specifications Met | Shank Thread Direction | Each | |
Ball Joints with Oversized Shank | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Cadmium-Plated Alloy Steel | |||||||||||
| 3/8"-24 | 5/16" | 20° | 1 1/4" | 7/8" | 2 7/16" | 1 9/16" | 2,900 | MIL-PRF-81322, MS21151 | Right Hand | 0000000 | 0000000 |
| 7/16"-20 | 5/16" | 20° | 1 1/4" | 7/8" | 2 7/16" | 1 9/16" | 2,900 | MIL-PRF-81322, MS21151 | Right Hand | 0000000 | 000000 |
Easy-Adapt Clevis Rod Ends
Make quick adjustments to these rod ends by inserting and releasing the clevis pins without the need to bend them into place. Also called yoke-end linkages, they support pivoting movement along one axis when threaded onto shafts, rods, valve pistons, and other assemblies. All are zinc-plated steel for moderate corrosion resistance.
For technical drawings and 3-D models, click on a part number.
| Shank Thread Size | ID | Jaw Opening Wd. | O'all Wd. | Shank Center Lg. | Shank Thread Lg. | Jaw Center Lg. | Tensile Strength, psi | Includes | Shank Thread Direction | Each | |
Zinc-Plated Carbon Steel | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 5/8"-11 | 5/8" | 5/8" | 1 1/4" | 2 1/2" | 1 1/4" | 1 1/4" | 60,000 | Snap-On Spring Clevis Pin | Right Hand | 0000000 | 000000 |
| 5/8"-18 | 5/8" | 5/8" | 1 1/4" | 2 1/2" | 1 1/4" | 1 1/4" | 60,000 | Snap-On Spring Clevis Pin | Right Hand | 0000000 | 00000 |
| 5/8"-18 | 5/8" | 5/8" | 1 1/4" | 3 25/32" | 1 1/4" | 2 17/32" | 60,000 | Snap-On Spring Clevis Pin | Right Hand | 0000000 | 00000 |