Designed for temporary mounting on smooth, nonporous surfaces, vacuum holders are easy to remove and reposition.

Attach sensors, tubes, and other components to T-slotted framing rails and structures.

Route wires, cables, and tubing along T‐slotted rails.

Use hinges to add doors, lids, and machine guards to T-slotted framing.

Attach and position phones, tablets, monitors, and other displays on T-slotted rails.

Add mounting feet and casters to T-slotted framing structures to level equipment, anchor legs to the floor, or add mobility.

Add rollers to T-slotted framing to create flow rails, ball transfer tables, and other manual conveyors.

Position proximity, photoelectric, and light beam sensors and switches.

Machine holes and slots or weld in place.

Also known as double cams, these complete cam handles have a durable, extra-large handle for clamping on fixture bases, plates, and workpieces. For fast adjustments, push down on the handle and the head applies pressure to quickly draw two parts together.

Combine track, mounting brackets, and hangers to create a system for hanging doors.

For use with a single line, these clamps brace pipe, tubing, and conduit directly against the mounting surface.

Route pipe, tubing, and conduit across strut channel.

For areas with low clearance, these clamps have the mounting fastener to the side of the material, rather than on top.

Secure insulated pipe to strut channel without pinching the insulation or exposing the pipe. These clamps are sized for use with insulated pipe and have a plastic insert that creates a seal around the insulation to prevent the pipe from sweating, which can cause mold and corrosion.

For use with a single line, these plastic clamps reduce wear on softer materials, such as tubing and cable, and prevent corrosion caused by metal-to-metal contact.

Route two lines of tubing with a single clamp. Commonly used in compressed air systems, these polypropylene clamps withstand moisture and most chemicals. They have a folding arm that closes to secure material.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Slide these clamps into strut channel and snap closed for quick installation with no tools required. They are noncorrosive, nonconductive nylon.

For a more secure connection than rail- and adhesive-mount clamps, weld the bottom plate of these clamps onto your rails. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

Secure two pressurized hydraulic lines with a single clamp. Mount these clamps directly onto rails, no adhesive or welding required. They fit tightly around the lines to reduce vibration.

A rubber cushion reduces vibration and wear from clamp edges. The cushion also protects lines of pipe, tubing, and conduit from corrosion caused by metal-to-metal contact.

Organize multiple lines of pipe, tubing, and conduit with one clamp. Wider than standard loop clamps, multiline loop clamps surround two lines of material to create a secure grip while holding the lines close to the mounting surface. A cushion covering the clamp reduces vibration and wear from clamp edges.

These clamps completely surround single lines of pipe, tubing, and conduit while holding them close to the mounting surface.

Compared to metal loop clamps, plastic loop clamps reduce wear on soft materials, such as tubing and cable. Clamps are nonconductive and noncorrosive.

Also known as conduit hangers, these hangers load from the bottom so you can add or remove material without removing the mounted hanger.

Mount these hangers on top of one another to organize multiple lines of pipe, tubing, and conduit at any angle.

Rubber cushions fit material tightly to reduce vibration and provide a more secure hold than loop hangers. The cushions also protect material from sharp edges and prevent corrosion caused by metal-to-metal contact.

These hangers provide maximum corrosion resistance in wet environments and stand up to frequent washdowns with harsh cleaners and sanitizers. Rounded edges, polished surfaces, and acorn or hex nuts that conceal threads reduce the number of places for bacteria to grow and make them easier to clean.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

Also known as pipe shields, these cradles provide additional support and prevent insulation from tearing when routing insulated pipe through loop hangers.

Also known as clevis hangers, these have a pivoting loop that adjusts for line movement and vibration. Combine with a threaded rod or other fastener to hang from the ceiling.

Use these close-fitting hangers for a more rigid hold around material than when using straps alone.

Attach these clamps to the flange of an beam, then hang a threaded rod from the threaded hole.

A mounting plate provides a more secure hold at the mounting surface.

A durable rubber cushion and mounting plate prevent corrosion and wear caused by metal-to-metal contact. The mounting plate is removable, so the U-bolts can be installed onto an existing line without needing to dissemble it.

These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.

Attach these supports onto metal stud knockouts to route cable, conduit, and tubing through metal studs.

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

Get everything needed for basic workholding on a machine table.

Attach to the end of a screw or threaded stud to apply uniform pressure on uneven and angled surfaces. Also known as toggle and swivel-foot pads.

These clamps are made of stainless steel for excellent corrosion resistance.

Clamp farther in from the edge of a workpiece than with other C-clamps.

Mount through the counterbored hole with a socket head cap screw to support and position workpieces and fixtures from the bottom or side.

Use these buttons to support and position workpieces and fixtures from the bottom or side. Their hex shape lets you screw them into a threaded hole with a wrench or socket.

Sealed at the top to prevent debris from getting inside and making them seize up, these guide pins are a good choice for machining fixtures.

Threading makes these guide pins easier to remove and replace than press fit, so they're useful for high-wear applications.

Install these pins in a plate or table and mate with holes in a workpiece for precise alignment.

Sized to fit with precision in machine table T-slots, use these keys to locate fixtures and vises on your machine table.

Prevent chips, debris, and small parts from falling into T-slots.

Install from the top of the T-slot track and secure with a quarter turn. Also known as quarter-turn T-slot nuts.

For mounting items to your machine table, these kits contain the full system of necessary components.

A magnetic base provides a solid mount on metal surfaces.

Use with DIN 3 rail. Add as many circuits as you need with these terminal blocks and accessories.

One of the connections on these terminal blocks is a socket instead of a traditional terminal, making it easy to swap out equipment or change your wiring even in small enclosures. Instead of having to attach wire inside the tight space of your enclosure, you can wire a connector wherever it’s easiest and then plug it into the socket.

Quickly troubleshoot or change wiring without any tools. These terminal blocks have a lever clamp that you flip up to insert wiring and flip down to lock it in place.

Hold and tighten right-hand threaded studs and rods, which screw into the opening at the tip of the driver.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.

Use brackets and connectors to create vertical and horizontal support arms.

Made with two pieces, these shaft supports secure your shaft parallel to your mounting surface and make it easy to access the shaft without having to slide it out or uninstall the support. Use these supports when working with light to medium loads where shaft alignment is not critical.

Create a support that fits the exact dimensions of your shaft to brace it along a flat surface. Good for use with square- and hex-profile shafts, these aluminum supports also work with round shafts of any diameter up to 1". Use them for light-to-medium-load linear motion applications where shaft alignment is not critical.

These shaft supports hold linear shafts perpendicular to the mounting surface.

Designed for use with right-hand, externally threaded rod ends, these rods have right-hand threads on both ends. Use them for remote valve operators, throttle controllers, shifting mechanisms, and virtually any push/pull assembly.

Similar to turnbuckles, these rods have right-hand threads on one end and left-hand threads on the other so you can make a linkage that adjusts for tension.

Attach ball socket end fittings to these studs to mount gas springs.

Also known as split pins, these have one prong slightly longer than the other so they’re easy to open. Bend prongs outward to secure.

A coil makes a stronger grip than standard hairpin cotter pins to prevent accidental release.

These pins combine the locking capabilities of a clevis pin with the precision diameter of a dowel pin for a tight fit.

Install or remove these pins from either side. Slide a retaining ring into the groove for a secure hold that takes up less space than a cotter pin.

Also known as roll, tension, split, and expansion pins, these pins have a slot along one side that you squeeze closed to install them into unthreaded holes.

For tough jobs, these spiral pins are 30% stronger than our standard coiled spring pins. They remain flexible after installation to absorb shock and vibration, and work well in holes that are out of round.

The tensile strength of these metric Grade B7 rods is about one and a half times higher than low-strength steel rods.

An economical alternative to Grade B7 and Grade B16 threaded rods, these metric Class 8.8 rods are suitable for fastening most machinery and equipment.

About half the strength of medium-strength steel threaded rods, use these metric fine-thread rods for light duty hanging, mounting, and fastening.

These Class 10.9 steel threaded rods are about 25% stronger than medium-strength steel rods.

These metric 316 stainless steel threaded rods are more corrosion resistant than 18-8 and 410 stainless steel threaded rods and have excellent resistance to chemicals and salt water.

These metric brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.

These metric threaded rods are made from nylon 6/6 and resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.