Reduce the chance of getting pinched when unclamping. These clamps have more space between the handle and the arm than other low-profile toggle clamps.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Mount these clamps to a bench top or other surface to keep workpieces in place.

Push the lever to lock the handle and prevent accidental opening.

Often used when assembling small parts, these small clamps have the holding strength of a full-size clamp.

Bolt to the side of an object. Often used to clamp lids and covers on containers.

Mount these clamps below a surface.

The handle locks in a horizontal position for more clearance above the clamp.

These clamps have mounting holes on the bottom.

Suitable for production applications, these clamps have double the service life of other air-powered toggle clamps.

The base fits into round or square holes on most workholding tables for clamping anywhere on the work surface.

Smaller than standard push/pull toggle clamps, these are often used for electronics and small fixturing applications.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Smaller than standard push toggle clamps, these are often used for electronics and small fixturing applications.

The handle can be rotated 125° for easier access or extra clearance above the clamp.

Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side.

Secure these clamps to a rail or bar.

Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel.

Eliminating the need for step blocks or other rear support, the pivoting rocker clamps workpieces of various thicknesses.

The stepped end provides support and quick height adjustment when paired with a step block.

Get everything needed for basic workholding on a machine table.

Designed to provide more clearance above the nut than standard clamps, these have an offset shape. Also known as gooseneck clamps.

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

Making minimal contact with the workpiece while holding securely, these clamps are good for small parts and can clamp into holes and notches.

Use these clamps to hold large round parts for machining. Each clamp comes with five lengths of chain that combine to accommodate different size workpieces.

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Press the lever to lock the clamp onto material.

These clamps meet DIN VDE 0680-1 for protection against accidental contact with live electrical circuits.

Hold large workpieces with a standard-size clamp. Slide the jaws to adjust the opening size.

Extend the handle to reach the clamp into tight spaces.

Use these tools for light duty clamping. Squeeze the handles to open; release to close.

Turn the knob to adjust the opening size.

A removable, heavy duty steel base plate provides a flat, durable clamping surface. Carry it where needed or mount the base plate to your workbench.

Press the lever down to lock these clamps, which fit in tight spaces and hold thin materials.

Angled jaws clamp sheets, bars, and U-channels at 90°.

Set includes 12 clamps and the installation pliers required for positioning and removal.

A highly durable construction with hardened steel pivot pins and bushings provides a long service life.

Push the lever to lock the handle and prevent accidental opening.

Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Secure a workpiece from the inside, leaving the outside clear for machining.

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Mount using the holes in the base.

These clamps have twice the capacity of standard fast-action bar clamps.

Pull the handle to lock the jaw in place and prevent loosening caused by vibration.

All adjustments can be made from one end, allowing clamping in tight spaces.

Place the arms on a pipe that is threaded at one end and at least 12" long to create your own bar clamp.

Each arm slides freely for quick, one-handed positioning. They lock when the screws are tightened onto a workpiece.

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

Clamp much farther in from the edge of the workpiece than with standard bar clamps.

Two swivel pads on each jaw pivot to grip nearly any shape of material.

Turn the handle to tighten these multipurpose tools for strong clamping in nearly any application.

Lighter weight than other metal clamps, these are less likely to bend thin material.

Made entirely of fiberglass, these clamps won’t transmit electricity and are chemical resistant. They're often used around electrical equipment as well as in plating and anodizing applications.

A bright finish makes these clamps easy to see.

With no handle or protruding screw, these clamps can fit into tight spaces.

Three screws apply pressure to three sides of a workpiece.

The jaws move in unison to apply even pressure and prevent twisting.

Plastic clamping surfaces prevent damage to material.

Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.

Combine fast-threading components to build a clamping assembly.

Hold workpieces at a 90° angle.

With five times the capacity of standard corner clamps, these secure two workpieces at a 90° angle.

Sized for small parts and tight spaces, these clamps have a pivoting pad at each end to hold workpieces at any angle up to 180°.

Hold and align up to three workpieces at 90° angles.

Switch the magnets on these clamps on and off for easy placement and removal of your workpiece.

Sets include clamps with different ODs as well as installation pliers.

Each jaw can be positioned at an angle to hold round, angled, and odd-shaped material.

Hold pipe and fittings together for tack welding.

Build a custom clamping system for holding lightweight objects such as beakers and laboratory equipment.

Hold larger workpieces than standard locking pliers. These tools lock in a vise-like grip around a workpiece and stay clamped in place.

Choose a stainless steel tool for environments where moisture and other contaminants are present. These pliers resist corrosion that can hinder joint movement, but the jaws will wear more quickly than a steel tool. Lock the jaws around a workpiece and they stay clamped in a vise-like grip.

Long jaws reach workpieces in recessed areas. These pliers lock in a vise-like grip around a workpiece and stay clamped in place to leave your hands free.

Secure these holders to a table or benchtop and slide in up to three pairs of locking pliers to create a hands-free way to hold your work.

Reach around closely spaced components and other obstructions. These pliers lock in a vise-like grip around a workpiece and stay clamped in place to leave your hands free.

Change out worn or broken springs in the handle of your locking pliers.