Bright colors and reflective stripes make workers stand out in high-risk areas and where low-visibility is a concern. Black fabric on the lower half keeps jackets looking cleaner longer than all-yellow jackets. These jackets meet Class 3 ANSI/ISEA 107 standards for workers that need to be seen by traffic at a minimum distance of ¼ of a mile. They have a zipper down the front.

Stand out in low-visibility areas with these brightly colored, reflective coats. They’re longer and more insulated than high-visibility jackets to keep you warm in temperatures as low as -50°F. Made of nylon, they have a wind- and water-resistant outer shell, with a layer of polyester insulation for added warmth. A storm flap snaps shut over the zipper to keep out wind and cold. Knit cuffs trap heat and hold sleeves in place. These coats meet Class 2 ANSI/ISEA 107 standards for workers who are on or near roadways.

When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under these coats.

Coats are knee length, providing more coverage than shirts. Breathable to keep you cool and comfortable, these coats protect against dirt and grime.

When choosing a size, consider individual body shape and clothing worn underneath.

Keep dry in wet and rainy conditions. These jackets have a storm flap that covers the snaps down the front. They’re washable and resist tears.

When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under these jackets.

Made of 99% polyester and 1% carbon fiber, these coats repel liquids. These knee-length coats are also known as barrier coats. They have knit cuffs to keep liquid from splashing into sleeves.

When measuring chest size, measure around the fullest part of your chest. Take all measurements over clothing you expect to wear under the coat.

Keep workers clean and protected from spills and splashes on food processing lines while reducing the risk of contaminating the food. These aprons contain metal and chemical additives that will set off metal detectors and show up on X-ray machines if they—or any piece of them—fall into your line. Use these aprons to help you comply with Hazard Analysis and Critical Control Point (HACCP) programs for food safety.

Coats extend past your knees to keep you dry in wet and rainy conditions. They have snaps down the front with a storm flap to help keep rain out. Made of durable material, they resist tears. They’re also washable.

When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under these coats.

Shirts are hip length to protect against dirt, grime, and light liquid splashes. They are breathable and lightweight to keep you cool while working. They have snaps down the front and open cuffs. Made of Polyethylene/Tyvek, these shirts have heat- and pressure-bonded fibers for a material that’s soft yet strong.

Wear once then toss—these disposable coats prevent dust, microbes, and other pollutants from contaminating your clean room space. Cleaned and individually bagged in a clean room, they won’t shed any lint or dust. These coats are polyethylene/Tyvek, which is made with heat- and pressure-bonded fibers that make for a soft yet tear-resistant coat. They hold up to limited contact with nonhazardous liquids, such as water and paint spray.

When choosing a size, consider individual body shape and clothing worn underneath.

Bib overalls have adjustable suspenders to modify the length.

When measuring chest size, measure around the fullest part of your chest. Find your waist size by measuring just above the top of your hip bone. Take all measurements over any clothing you expect to wear under these suits.

Protect against chemical spills and splashes. These coats are polyester with a PVC coating inside and out, and extend past your knees for added protection. Snaps down the front and a storm flap helps keep liquid splashes out. They have open cuffs.

When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under these coats.

Hoods—Fasten a hood (sold separately) to the collar snaps.

These jackets meet NFPA 70E standards for protection against electrical arc flashes for personal protection equipment (PPE) category 2. They also meet ASTM F2733 standards for protection against flash fires. Check the PPE category and minimum arc rating provided for your workplace, and then select all required clothing and personal protective equipment to meet the minimum arc rating. Arc rating measures a garment’s ability to insulate the wearer from burns; the higher the arc rating, the greater the flame resistance. These jackets are made of PVC-coated Nomex. They have snaps down the front and a storm flap to keep rain out. They have hook and loop cuffs; tighten to fit your wrist or gloves.

When measuring chest size, measure around the fullest part of your chest. Take all measurements over any clothing you expect to wear under these jackets.

Hoods—Fasten a hood (sold separately) to the collar snaps.

Create a barrier between you and your clean room. These coats keep dust, microbes, and other pollutants that might be on your body from contaminating the area. Reusable when washed according to clean room standards, they’ll last up to 100 washes. Make sure to wash them before your first wear. They are suitable for use in clean rooms rated to both Federal Standard and ISO classes. In both systems, clean rooms with lower class ratings have fewer contaminants. Coats are knee length.

When choosing a size, consider your body shape and the clothes you’ll wear underneath.

Shield your torso, face, and hands from extremely cold materials, such as liquid nitrogen and dry ice. These kits include a cryogenic apron and gloves that withstand temperatures as cold as -320° F. Made of Cordura nylon fabric, the aprons are waterproof and resist cuts. They have adjustable neck and waist straps with buckles for quick removal. A breathable liner in the nylon gloves wicks moisture. Their open cuff design lets you easily slip them on and off. These kits also have a polycarbonate face shield that blocks splashes and won’t easily crack if dropped. Unlike standard face shields, these shields won’t fog up when cold liquids splash them. The face shield has a ratchet adjustment in the back and a pinlock adjustment in the front, so you can get a comfortable fit.

Keep your arms free while working in the cold—these vests keep you warm without the bulky sleeves of a coat. Side stretch panels allow you to twist and stretch your body more freely than in a jacket or coat.

Protect against chemical spills and splashes.

Bib overalls have adjustable suspenders to modify the length.

Detachable Hoods—Fasten a hood (sold separately) to jackets with collar snaps.

Also known as kickback vests, these vests help prevent injuries if a chainsaw or other cutting tool jerks toward your chest.

Stand out and keep your core insulated in temperatures as frigid as -50° F.

Designed to meet clean room standards, these aprons prevent pollutants from contaminating the space. Aprons resist spills and splashes from acids, alkalies, and other chemicals.

Keep mist, drips, sprays, and splashes off your robot arm. Made of plastic-laminated polyester fabric, these covers resist water and other noncorrosive fluids. For example, they’re useful when your robot fetches a freshly milled part from inside a CNC machine dripping with coolant. These covers are tailored for specific robot models—no need to cut, sew, or customize. They slide on and off the arm like a sleeve. Because the fabric stretches, these covers hug your robot arm without hindering its movement. Elastic at each end clinches the arm, keeping these covers in place as it works. Each cover is clean room laundered, HEPA dried, and vacuum sealed, so they won’t bring contaminants to your process.