These zinc-rich coatings offer the protection of hot-dip galvanizing to keep iron and steel free of rust and corrosion. They're designed for outdoor use, but can also be used indoors in well-ventilated areas.

Coatings with 99% zinc withstand temperatures up to 750° F.

Coatings that cannot be sold to Canada are restricted by product labeling requirements.

Capture intricate details when creating prototypes, molds, and linings with these easy-to-mix two-part compounds. This urethane is water and abrasion resistant.

View our selection of release agents. View additional information about the hardness of these materials.

Create detailed rubber shapes that are ready to use in fifteen minutes or less. Unlike traditional casting compounds, which can take up to 24 hours to set, these compounds harden after two minutes, and can be removed from molds within fifteen. Use them to make your own prototypes, molds, and linings.

Combine acrylic or silicone with a 69° cure temperature compounds in different ratios to adjust the consistency from thin to thick. Thin mixtures are easier to pour and better for filling small crevices.

Silicone with a 70° cure temperature compounds are a putty that you can mix with your hands and form into any shape. Press an object into these compounds to create a mold for casting duplicates. They do not shrink as they dry, so textures and other fine details are captured faithfully. Soft silicone is more flexible and easier to peel off of molds than firm silicone, especially when making complex shapes. Firm silicone holds its shape better than soft silicone, so small ridges and channels are less likely to collapse or deform while making molds.

Compounds with dispenser gun come ready to use—no mixing required—and won’t leave a mess.

Combine the liquid components to form a putty that can be molded into or around any shape. Use these compounds to capture intricate details when creating prototypes, molds, and linings.

View our selection of release agents. View additional information about the hardness of these materials.

Create transparent molds to monitor fill levels, differentiate parts at a glance, and avoid damaging parts when cutting the mold away. These casting compounds are two parts that activate when mixed.

Urethane compounds are tougher than silicone compounds, so your molds will last longer. Although not required, curing urethane molds inside a vacuum chamber improves their clarity. By removing trapped air bubbles, the chamber prevents the finished mold from looking speckled.

Silicone compounds handle higher temperatures than urethane compounds—up to 570° F. Silicone also cures faster than urethane, and it won't shrink as it cures, which means you won't need to guess at the final size of your mold. Because silicone compounds trap air bubbles when mixed, they must be cured inside a vacuum chamber. The chamber removes the trapped air bubbles, strengthens the mold, and improves its clarity.

View our selection of release agents. View additional information about the hardness of these materials.

After these compounds cure, they're tough enough to be machined. They are easy-to-mix two-part compounds that capture intricate details when creating prototypes, molds, and linings.

View our selection of release agents. View additional information about the hardness of these materials.

Replicate even the most complex details when creating prototypes, molds, and linings. This easy-to-mix two-part compound flows smoothly into crevices. Cast up to 1/2" in thickness at a time.

View our selection of release agents. View additional information about the hardness of this material.

Create rubber molds that retain their shape for decades—they won’t soften, degrade, or warp, so you can continue to replicate intricate parts. Because these compounds don’t shrink as they cure, they are more accurate and predictable than other compounds.

View our selection of release agents. View additional information about the hardness of these materials.

Create lightweight molds with these two-part compounds. They expand as foam after they’re poured to fill every cavity. The denser the foam, the less it will expand. Before casting, apply petroleum jelly (not included) to prevent sticking, stretching, and tearing. It won't cause the foam to collapse as it cures.

Flexible compounds cure into soft, open-cell foam, which absorbs water, air, and gases. They are often used to cast gaskets, cushions, and other bendable objects.

Rigid compounds form stiff, closed-cell foam, which prevents water and air from flowing through the part. Machinable, they’re dense enough to create prototype modeling blocks, so you can test setups without wearing down tools.

These food-grade compounds comply with FDA 21 CFR. They are easy-to-mix two-part compounds that capture intricate details when creating prototypes, molds, and linings.

View our selection of release agents. View additional information about the hardness of these materials.

This silicone compound offers good resistance to acids, oils and salt water. Use it to capture intricate details when creating prototypes, molds, and linings with this easy-to-mix two-part compound. It is a durable and tear-resistant silicone, which easily demolds.

View our selection of release agents. View additional information about the hardness of these materials.

Apply this liquid for a skin-tight protective coating that insulates and resists moisture, acids, and corrosion. It adheres to metal, plastic, vinyl, rubber, and composite surfaces.

Liquid rubber is moisture and crack resistant. Use it as a seal on plastic tape. Allow 20 minutes between coats.

Liquid vinyl is for use on electrical connections and terminals.

Liquid that cannot be sold outside the United States is restricted by product labeling requirements.