We will reply to your message within an hour.
These grips are sized to fit in tight areas.
Because these grips resist absorbing water, they are less likely to crack or corrode than other types of plastics and metals.
These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.
Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.
Wrap the split gland of these grips around ethernet cables with an RJ45 connector or other already installed cables for a water-resistant seal with your enclosure.
Extend your cord’s life while stopping it from coming loose in places that are sanitized with water or steam as hot as 300° F, such as food plants and clean rooms.
A rubber bushing with an oval slot resists water and provides entry for building cable, which is also known as Romex type NM-B or type UF-B cable.
Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.
Snap these cord grips into place to secure cable in wet environments.
Push to install these cord grips in wet environments and high-movement applications such as robotics and handheld equipment.
Secure cords installed through enclosures and panels in wet environments while protecting them against sharp bends. With a flared end that keeps cords from bending without limiting too much motion, these grips extend cord life.
Made of nylon with a nylon mesh extension, these grips resist most chemicals. The mesh provides a secure hold in applications where cable is pulled or in motion.
Made of PBT, these grips resist soaking up water in washdown and other wet environments while securing cords with an extra-strong hold.
Secure cords in washdown areas where there’s minimal space—these cord grips curve 90° to relieve stress from bending.
Tighten the screw-down clamp for superior pull-out resistance.
These grips are made of nylon, which resists most chemicals. The nylon mesh extension provides a secure hold when the cable is pulled or in motion.
Lighter in weight than steel and brass grips, these aluminum grips are strong enough to secure cords in demanding wet environments.
Stop cords from coming loose in wet environments while keeping them along the side of your enclosure in tight spaces.
With an oval bushing hole, these lightweight grips secure flat building cable, such as Romex and Festoon cable, in wet areas. All offer strain relief to extend cable life.
Use these lightweight grips to secure cords entering knockouts at a 45° angle in wet, tight spaces while easing the stress from bending. Made of aluminum, they’re lighter in weight than steel and brass grips yet durable.
Keep your cord at a gentle angle without sacrificing a tight hold, even in tough, wet environments.
Create a tight grip on cords in wet environments while reducing stress from bending—the 90° angle of these cord grips routes cords to fit tight spaces in enclosures and panels.
Keep cords from coming loose and seal water out of enclosures in extremely cold labs and storage areas. Thanks to their plastic bushing and rubber O-ring, these grips withstand temperatures as low as -75° F.
Suitable for use in applications where cords are underwater—these grips are rated IP68 for protection from prolonged submersion.
These grips have an extension that provides extra support for moving cable and prevents kinking for longer cable life.
Secure cable installed through enclosures in wet environments while venting air to protect electronics from condensation.
These grips are the most corrosion resistant of any of our submersible metal cord grips.
An internal ring keeps cable with braid shielding grounded to the body of the grip to block electromagnetic interference (EMI).
These cord grips are lightweight yet durable. They have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the connection.
Secure cords in wet and industrial environments with little room—these grips curve 45° to relieve bending stress.
These stainless steel grips offer the most protection from wet, corrosive environments of any of our metal wet-location cord grips. They are rated IP67 for protection from temporary water submersion.
The mesh offers a secure hold in applications where cable is pulled or in motion. It reduces stress on the cable and prevents kinking for longer cable life.
Stronger than aluminum cord grips, these grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.
Stronger than aluminum cord grips, these steel grips are zinc plated for corrosion resistance. They have a steel locknut and metal-reinforced O-ring that prevents liquid from entering the connection.
Made of nylon, these grips resist chemicals. Install them in panels and enclosures—they have a zinc-plated steel locknut and metal-reinforced rubber O-ring that prevents liquid from entering the enclosure.
Also known as cable-entry seals, the cable-entry side has heat-shrinkable polyolefin with an adhesive lining.
Stainless steel construction offers the most corrosion-resistance of any of our multi-diameter wet-location cord grips.
These grips are nickel-plated brass for good corrosion resistance.
Securely connect cable in sanitary environments such as food plants with these watertight cord grips.
These grips meet Class III, Divisions 1 and 2 standards for use in hazardous locations.
These 90° elbows meet Class III, Divisions 1 and 2 standards for use in hazardous locations.
Grips have a rubber inner grommet with multiple holes and a rubber O-ring that create a tight seal to prevent liquid from entering the connection.
The cable-entry side has heat-shrinkable polyolefin with an adhesive lining. These are also known as cable-entry seals.
The face of these grips is flush with the cable-entry point for a seamless appearance. They have a thin, flexible seal that covers the holes until you push a cord through.
Peel away layers of rubber inserts to fit around cord grips, even when you don't know the exact diameter.
Modify these cord grips to get the right fit for your cord even when you don't know the exact diameter.
These grips have a thin, flexible seal that covers the holes until you push cords through.
The face of these grips is flush with the cable-entry point for a seamless appearance.
Secure multiple flat cable through one cord grip—reducing the space and number you need for a project, as well as saving time.
Rated IP68, these grommets form liquid-tight seals around wire, cable, and cords to protect them against dust as well as submersion in a maximum of one meter of water.