Thicker than standard external retaining rings, these rings withstand greater force.

For a smooth profile and better clearance than standard external retaining rings, the lugs on these rings point inward.

The curved design of these rings works like a spring, taking up play for a tight hold.

These coiled rings can be wound into place on a shaft without tools.

Also known as E-style rings.

These rings are reinforced to withstand faster rotation than other side‐mount retaining rings. Also known as reinforced E‐style rings.

Also known as bowed E-style rings, these have a curved design that works like a spring, taking up play for a tight hold.

The wide flange provides better load distribution than standard external push rings and can be used to cover oversized holes. Also known as thread cutting nuts.

Also known as flat-style speed nuts, these have a large surface to distribute loads better than standard and flanged external push rings.

Also known as constant-section rings, these rings have open ends and a profile that does not taper like other external retaining rings. Use them with linear bearings on support rail shafts.

Slide these rings into a groove near the end of the shaft and the tab locks them in place.

These coiled rings can be wound into place inside a bore or housing without tools.

Squeeze these rings to place them in the groove inside a bore or housing.

Thicker and stronger than standard internal retaining rings, these withstand greater thrust loads.

With teeth along the inside, these retaining rings hold chamfered shafts inside the housing of your equipment.

Wind these retaining rings into a groove—no tools required for installation.

Pull these rings open with retaining ring pliers, pass over the end of a shaft, and release to spring into a groove.

Assortments include pliers to install external rings.

With flexible teeth that slide smoothly over threads of any pitch, these push nuts can be used alone for light-duty applications or as a jam nut.

Hex speed nuts can be gripped with a wrench for ease of removal.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

Installing and removing a collar is as easy as pushing down and lifting up a clamp lever.

A threaded lever lets you tighten these collars with more torque than other quick-release styles, ensuring that they stay put on your shaft.

Two knurled sides provide micrometer-like movement for precise width adjustments.

One side of these collars locks down like a standard one-piece shaft collar; the other has a flush face that's flat to 0.0005", which lets you mount the collars on a shaft next to precision bearings, sprockets, and gears.

Formed to offset the weight of the clamping screw, these collars won't wobble or vibrate when shafts are spinning—even at high speeds.

Made of chemical-resistant nylon, these collars are suitable for washdown applications.

Suitable for use in washdown applications, these plastic collars also offer good chemical resistance.

With larger screws than those found on standard clamping collars, these provide a stronger grip on your shaft without using additional screws.

Although these collars fit inch-sized shafts, they have a metric OD and width for use with metric equipment.

Wider than standard shaft collars with twice the number of clamping screws, these ensure a better grip for greater holding power.

Offering the benefits of a two-piece collar in a one-piece design, these collars swing open for positioning then close anywhere on your shaft.

Secure items to either side of these collars—each half has a flat end with a tapped hole

Install these collars anywhere on a shaft without removing components or having access to the ends of the shaft.

Two tapped holes on the face of these collars allow you to fasten them to gears, pulleys, and sprockets.

With a nylon insert that grips your threaded shaft or spindle without damaging its threads, these locknuts—also called shaft nuts—hold bearings, bushings, gears, and pulleys prone to vibration tightly in place.

Used in pairs or with another bearing retaining nut, these jam nuts—often called shaft nuts—hold bearings, bushings, pulleys, and gears in place on your threaded shaft or spindle.

Slide these one-piece collars onto the end of your shaft to create an end-stop for linear components.

Install these collars anywhere on a shaft without removing components or having access to the ends of the shaft.

To install, slide these one-piece collars onto the end of your shaft.

To install, slide these one-piece collars onto the end of your shaft.

Includes a black, blue, green, purple, and red tag ring.

The narrow end restricts the movement of rope and chain, and the wide end allows room to attach multiple connectors.

Flat sides allow webbing and strapping to lay flat, so they won't slide and bunch.

Best for attaching different widths of webbing and strapping, the flat sides ensure they lay flat and won't bunch or slide.

Slide the lock down to open the latch and release it to lock these carabiners.

Prevent twisting in your rope or line with these swiveling carabiners. To open, pull the latch down, twist 90° and push in.

Clamp lids onto sanitary stainless steel drums using these leverlock closing rings, which create a tight seal and are easy to put on and take off.

Sized to fit snugly around pipe, these collars are often used to support pipe passing through floors and walls.

To avoid gouging and marring your pipe while making adjustments, these collars have flats where you can grab and rotate the pipe with a wrench. They're sized precisely for a tight fit around pipe, so they're often used to support pipe passing through floors and walls.