Also known as compression cam locks, these locks create a tighter hold than a traditional cam lock, making them useful for doors that have a seal. Turn the head a quarter turn to lock, then turn it another quarter turn to create compression and minimize rattling from vibration. Since they lock with a hex key, these locks are great if you want to secure an enclosure with a simple keying system.

Locks with a fixed latching distance are best when you know the precise distance you need. Since you won’t have to adjust the cam into position, these are faster to install than those with an adjustable latching distance. All include multiple cams, so you can change the fixed latching distance.

Locks with an adjustable latching distance handle a wide range of latching distances, so they’re best for tasks when precise distances are unknown. Adjust the position of the cam before you begin to install them. They project further into the enclosure than those with a fixed latching distance.

Stainless steel locks are more corrosion resistant than zinc and aluminum locks. They won’t rust in areas that are constantly exposed to moisture. Although less corrosion resistant than stainless steel, aluminum locks resist rusting better than zinc locks. They’re also the lightest in weight.

For locks with mounting holes, the installation hole can be made with a round hole instead of the irregularly shaped standard cam hole. This is especially helpful if the material of the door is difficult to cut or part of an existing structure. Push the lock into your through hole and secure it with fasteners so it won’t rotate as you turn the head.

IP or NEMA rated locks have a gasket that helps keep low-pressure washdowns and dust from entering through the lock. This helps you maintain your sealed enclosure's IP or NEMA rating.

For technical drawings and 3-D models, click on a part number.

A gasket stops water from getting past these locks during high-pressure, high-temperature washdowns common in food processing plants. This helps you maintain a sealed enclosure's IP rating. Also known as quarter-turn locks, these locks rotate a cam 90° to secure your door or drawer. They lock with a hex key, so they’re great if you don’t want to keep a complicated keying system. Made of stainless steel, they resist corrosion, even when exposed to constant moisture. These locks come with multiple cams to accommodate different latching distances.

For technical drawings and 3-D models, click on a part number.

Spot when these locks are open with just a glance—a red indicator shows they're unlocked. Also known as compression cam locks, their cam seals more tightly against a door or drawer than a standard cam to reduce rattling from vibration. Using a hex key (sold separately), turn the head a quarter-turn to lock, then another quarter-turn to draw the cam firmly against your surface. Since they lock with a hex key, they’re great if you want a simple keying system. All come with multiple cams to accommodate different latching distances.

To help maintain a sealed enclosure's IP and NEMA rating, these locks have a gasket that stops water and dust from getting past the lock. Made of stainless steel, these locks resist corrosion, even in environments with constant moisture.

Locks with a fixed latching distance are best when you know the precise distance you need. Since you won’t have to adjust the cam into position, these are faster to install than those with an adjustable latching distance.

Locks with an adjustable latching distance are best for installations when precise latching distances are unknown. Adjust the position of the cam before you begin to install them. They project further into the enclosure than those with a fixed distance.

For technical drawings and 3-D models, click on a part number.

Install these locks in smaller-than-standard diameter through holes to secure enclosure doors and file drawers. They open with a hex key, so they are great for a facility where you don’t want a complicated keying system. Also known as quarter-turn locks, these locks have an attached arm that rotates 90° to lock your enclosure. A gasket prevents water, dust, and dirt from getting into an enclosure through the lock, helping you maintain an IP65 and NEMA 4 rating in your sealed enclosure. All come with multiple cams to accommodate different latching distances.

Pull tabs (sold separately) make opening your door or panel easier.

Sealing covers (sold separately) keep water and dust from getting inside the lock cylinder.

For technical drawings and 3-D models, click on a part number.

Install these locks in smaller-than-standard-diameter through holes on cabinet doors and file drawers. Also known as compression cam locks, they create a tighter hold than standard cam locks in high-vibration environments. Turn the head 90° to lock, then turn it another 90° to draw the cam firmly against your enclosure. The second turn results in a tighter hold, which is ideal for enclosures with a seal and reduces rattling from vibration.

These locks open with a hex key (sold separately), so they’re great for a facility where you don’t want to keep a complicated keying system. They have an adjustable latching distance to handle a wide range of latching distances, so they’re best for spots where precise distances are unknown. Adjust the position of the cam before installing them. They project further into the enclosure than those with a fixed latching distance.

Locks with a screw cam allow you to easily adjust the latching distance and tension over time.

Stainless steel locks resist corrosion when exposed to constant moisture.

IP65 and NEMA 4 locks have a gasket that blocks water, dust, and dirt from getting into a sealed enclosure through the lock, helping you maintain both ratings on your enclosure.

Pull tabs (sold separately) make opening your door or panel easier.

Sealing covers (sold separately) keep water and dust from getting inside the lock cylinder.

For technical drawings and 3-D models, click on a part number.

Get the vibration resistance of a tight-hold lock with the simple operation of a quarter-turn lock. These locks have a spring-loaded bushing that stops your door from vibrating open. However, they don’t close as tightly as tight-hold locks. When the lock isn’t fully closed, the bushing stays depressed to signal it’s not secure. These locks open with a female hex key (sold separately), so they match a keying system that’s common for industrial enclosures and other machinery but are more secure than locks that open with a male hex key or screwdriver. Their flat, concealed design also stops others from tampering with them using pliers.

These locks include a gasket that prevents water, dust, and dirt from getting into your enclosure through the lock. This helps you maintain the IP65 and NEMA 4 ratings of your sealed enclosure. To accommodate different latching distances, they come with multiple cams.

For technical drawings and 3-D models, click on a part number.

Trigger a light, alarm, or other device to signal your door is unlocked. These locks have a magnet on the cam that is detected by a sensor (required, sold separately). When you unlock the door, the magnet moves out of the sensing range, activating a switch that turns your device on or off. Lock the door to reset the switch. When choosing a lock, consider the magnet location that works best for your setup. Install your sensor next to the side of the cam where the magnet is located. You cannot use these locks near existing magnetic fields, since they could interfere with the sensor.

These locks open with a hex key (not included) for a simple keying system. Also known as quarter-turn locks, they have a cam that rotates 90° to close enclosure doors. You can adjust the cam’s latching distance, so these locks are best for jobs when precise distances are unknown. Adjust the position of the cam before installing.

A gasket stops dust and water from getting into your sealed enclosure through the lock. This helps you maintain the enclosure’s IP65 and NEMA 4 ratings.

Single pole, double throw (SPDT) sensors can be set to turn a device from off to on (normally open) or from on to off (normally closed).

Sensors with a light illuminate when the latch is open, so you can see the inside of your enclosure when you swing open the door.

For technical drawings and 3-D models, click on a part number.

A hex key (not included) opens and closes these cam locks, simplifying your keying system. Also known as quarter-turn locks, they have a cam that rotates 90° to lock cabinet doors and other enclosures. A gasket prevents water, dust, and dirt from getting into the enclosure through the lock. This helps you maintain your sealed enclosure’s IP65 and NEMA 4 ratings.

These locks come with three cams, so you can choose between three different latching distances. Each individual cam has a fixed latching distance. Since you won’t have to adjust the cams into position, these locks are faster to install than those that have cams with an adjustable latching distance. Locks with a roller cam rotate more smoothly than those with straight and offset cams, making them easier to open and close. The cam won’t scratch or flake enclosure surfaces to protect electronics inside from paint or metal chips.

For technical drawings and 3-D models, click on a part number.

To help maintain a sealed enclosure's IP65 and NEMA 4 rating, these locks have a gasket that prevents water from getting past the lock during low-pressure washdowns. They also help keep out dust, dirt, and precipitation. Press the button to pop the handle out; push the handle shut for a secure hold. Since they lock with a hex key, these locks are great if you want to secure an enclosure with a simple keying system. When you shut the handle, a lever raises to press your door or drawer closed with an attached screw. Also known as compression cam locks, their lever creates a tighter seal than a rotating cam, so they're better at reducing rattling from vibration. Turn the screw on the lever to adjust the latching distance and tension over time. These locks have a flush design and their handle folds into a recessed position, so they stay out of the way. However, they might extend further into your enclosure than locks with a standard profile.

Locks with a color-revealing indicator let you quickly see if they’ve been opened. When the lock has been opened, the indicator turns red. These work great if you have many cabinets that need to be restocked throughout the day, so others know right away if the cabinet has been opened. Use a special indicator reset key (sold separately) to change the indicator from red to green.

For technical drawings and 3-D models, click on a part number.

A hex key opens these locks, making them great for a facility where you don’t want a complicated keying system. Also known as quarter-turn locks, these locks have a cam that rotates 90° to lock cabinet doors, file drawers, and other enclosures. Add a padlock for extra security. A gasket prevents water, dust, and dirt from getting into an enclosure through the lock. This helps you maintain an IP65 and NEMA 4 rating in your sealed enclosure. All come with multiple cams to accommodate different latching distances.

For technical drawings and 3-D models, click on a part number.

Open and close these locks with a hex key (not included) for an uncomplicated keying system. Often installed on server cabinets and electrical panels, they have a handle that swings smoothly when you lift it to latch and unlatch the door. The handle lies flat when locked, which means it won’t snag anything passing by. Add a padlock for extra security.

Also known as quarter-turn locks, these locks have a cam that rotates 90° as you swing the handle. They come with multiple cams, so you can change their fixed latching distance. An O-ring stops dust and water from getting into your sealed enclosure through the lock. This helps you maintain the enclosure’s IP65 rating.

For technical drawings and 3-D models, click on a part number.

Use a 5/16" hex key to open and close these locks. They’re good for use on sliding doors. A hole must be drilled in your panel for hex key access when mortise mounting. Capacity is the maximum amount of force the lock can withstand.

Style A has front tab mounting holes for mortise mounting.

Styles B and C have both side and back mounting holes, so they attach to the side of the panel or mortise into the panel.

For technical drawings and 3-D models, click on a part number.