We will reply to your message within an hour.
More
Three tapped counterbored holes and three through-holes provide mounting flexibility.
One side is unfinished for milling custom pulleys, threaded hubs, sprockets, collars, knobs, sensor targets, or just about anything imaginable; the other side is a one-piece clamping coupling for mounting whatever you’ve created to your shaft.
A removable collar allows access to the shaft without unbolting the flange. For use with light to medium loads where shaft alignment is not critical, these supports allow you to hold linear shafts perpendicular to the mounting surface. Secure the shaft by tightening the clamping screw.
These shaft supports hold linear shafts perpendicular to the mounting surface.
Use these bearings for light loads and small shafts. The closed backing blocks out dust and other contaminants.
Designed with a thin, compact housing, these bearings are good for space-constrained applications.
Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with two-bolt flange.
The lubricant in these mounted ball bearings is NSF registered H1 and FDA compliant for incidental contact with food.
An elongated mounting hole on one side of the flange lets you adjust the position of these bearings without having to remove your shaft.
Used in food, beverage, pharmaceutical, and chemical plants, these mounted ball bearings are IP69K certified for washdown environments and have a two-bolt flange for mounting.
These bearings have the highest speed ratings of any mounted ball bearing in our offering.
Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange.
Use these bearings in corrosive environments and under water.
Ball bearings operate with less friction than other bearings, so you can run them at higher speeds.
These roller bearings handle extremely high speeds for their small size.
A bolt in each corner makes for a secure, even hold.
Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange.
The lubricant in these mounted ball bearings is suitable for incidental contact with food.
Made to withstand frequent washdowns, these bearings are permanently lubricated, which means you’ll never have to add lubricant. Use them in hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants.
With a four-bolt flange for mounting and an IP69K certification approving them for washdown environments, these mounted ball bearings are used in food, beverage, pharmaceutical, and chemical plants.
The tapered rollers in these bearings support large shafts at high static loads.
Rated IP69K for washdowns, these bearings stand up to frequent cleanings in food, beverage, pharmaceutical, and chemical plants.
With all three mounting holes on one side, you can position the bearing above or below the mounting surface.
Also known as Oilite® bearings.
Increased iron content makes these bearings stronger and more resistant to shock loads than standard oil-embedded bearings; however they operate at lower speeds.
For applications with frequent starts and stops, the oil in these bearings contains particles of slippery PTFE that lubricate the bearing during startup.
With oil for reduced friction and iron for added strength, these bearings handle frequent stops and starts in high-load applications.
Support heavy loads that are often found in bottling and filling lines in food plants—these bearings contain extra iron and FDA-compliant oil. They’re flanged, so they handle loads both parallel and perpendicular to the shaft.
These bearings come with a traceable lot number and material test report. They are also known as Oilite® bearings.
The oil in these bearings is suitable for incidental contact with food.
Use where high loads and speeds are not required.
A slit running along the length of these bearings allows you to quickly slip them into a housing—no tools required.
Reinforced with polyester fabric, these plastic bearings have load and speed capabilities comparable to metal bearings.
An aluminum shell adds strength.
Good for underwater applications, these bearings won’t swell or warp when wet.
Made of FDA listed materials for use in food applications, these bearings also withstand caustic and washdown environments.
These bearings stand up to a wider range of chemicals than other dry-running flanged sleeve bearings.
Graphite provides a layer of dry lubrication that operates in high-temperature environments.
Use these bearings in applications with frequent starts and stops because they operate with very little friction.
Compensating for minor shaft misalignment and not requiring lubrication, these sleeve bearings swivel to self-align and are dry running. They don’t need a housing and you can install and replace them without any tools because they’re slip fit.
Made of acetal with a PTFE filler, these bearings handle velocities up to twice as high as standard acetal bearings. They swivel to compensate for a small amount of shaft misalignment.
The addition of iron and aluminum gives these aluminum-bronze bearings high strength and excellent corrosion resistance—making them suitable for use in marine and mining applications.
These bronze bearings are strong, wear resistant, and excellent at handling shock loads.
Furnished with a traceable lot number and material test report, these bronze bearings are strong, wear resistant, and excellent at handling shock loads.
Adapt needle-roller thrust bearings to use on unhardened, unground surfaces.
Create a custom mounted bearing by adding your own bearing to these flanged housings.
Quickly mount bearings in these precision-flanged housings, no machining required.
The flanged housing makes these bearings a good solution for vertical linear motion applications.
The shell, housing, and balls of these bearings are stainless steel for excellent corrosion resistance.
The Frelon liner on these bearings allows them to stand up to a wider range of chemicals than other flange-mounted linear sleeve bearings.
A ceramic coating makes high speeds as well as rapid acceleration and deceleration possible.
A flange with mounting holes makes it easy to attach a load to these bearings. Create a compact linear and rotary motion system for robots and other applications requiring complex, fast movements, by combining them with ball splines.
Slide up to two linear ball or sleeve bearings into these housings and secure them with the included internal retaining rings.
Sized specifically to adapt standard shaft collars to pipe, these bushings create a tight fit.