About Paint and Protective Coatings
More
Epoxy Potting Compounds for Harsh Environments
Tough enough to be permanently submersed in seawater, these compounds protect sensitive electronics, such as circuit boards, semiconductors, and sensors in harsh environments. They resist moisture, salt, and chemicals, so you can use them in corrosive oil, marine, and mining applications. These compounds can also be used within autoclaves. Because they are epoxies, they are rigid, resist wear, and create excellent electrical insulation. They withstand a wide range of temperatures, and this formulation won’t crack or split as components heat up and cool down.
They come in a cartridge, so you can apply them precisely. To dispense, they require a mixer nozzle and gun (both sold separately).
Dry Time | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Container Size, fl. oz. | Consistency | Touch, hrs. | Overall, hrs. | Hardness Rating | Dielectric Strength, V/mil | Temp. Range, °F | Environment | For Use On | Autoclavable | Each | |
| 1.69 | Thick Liquid | 12 | 24 | Extra Hard | 500 | -50° to 350° | Corrosive, Salt Spray, Submersible | Brass, Bronze, Copper, Steel, Stainless Steel, Cast Iron, Titanium, Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PVDF Plastic, Polyimide Plastic, HDPE Plastic, Nylon Plastic, PEEK Plastic, Polyethylene Plastic, UHMW Plastic, Polypropylene Plastic, Glass | Yes | 0000000 | 000000 |
| For Cartridge Size | Each | |
| 1.69 fl. oz. | 00000000 | 000000 |
| For Cartridge Size | Each | |
| 1.69 fl. oz. | 00000000 | 00000 |
Coolant-Resistant Surface Fillers
Repair small leaks and cracks in coolant systems for commercial vehicles and industrial equipment. These surface fillers meet ASTM D3147 for their ability to stop leaks in engine cooling systems. Pour them into your coolant to fix both internal and external leaks. They contain ceramic microfibers and copper particles to create a permanent seal. They’re compatible with antifreeze and other coolant system additives.
Container | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size, fl. oz. | Type | Begins to Harden, min. | Reaches Full Strength, min. | Consistency | Temp. Range, °F | Color | For Use On | Each | |
| 16 | Jug | 7 | 10 | Thick Liquid | Not Rated to 500° | Brown | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Galvanized Steel, Galvanized Iron, Titanium, Acrylic Plastic, Polystyrene Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, PTFE Plastic, Polyethylene Plastic, Polypropylene Plastic | 0000000 | 000000 |
Fuel-Resistant Surface Fillers
Also known as sloshing compounds, these two-part epoxies bond to rough and rusty surfaces in fuel tanks to repair leaks and prevent further corrosion. They withstand permanent immersion in fuel, oil, and harsh solvents. Use them with metal, plastic, and fiberglass tanks. Mix the smaller can with the bigger one and pour into your fuel tank. Rotate the tank to coat the interior and dump out any excess. Allow to cure overnight. Size listed is the combined total of the two parts.
1.5-pint container can treat a 10-gallon fuel tank. 3-pint container can treat a 20-gallon fuel tank.
Container | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size, pt. | Type | Begins to Harden, min. | Reaches Full Strength, hrs. | Consistency | Mix Ratio | For Use Outdoors | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
| 1.5 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 000000 |
| 3 | Can | 5 | 24 | Thick Liquid | 2:1 | No | 70° to 90° | Amber | Drill, Sand, Tap | Aluminum, Brass, Bronze, Copper, Silver, Steel, Stainless Steel, Cast Iron, Galvanized Iron, Galvanized Steel, Titanium, Acrylic Plastic, Polycarbonate Plastic, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Nylon Plastic, Polyethylene Plastic, Polypropylene Plastic, Vinyl Plastic, Fiberglass, Ceramic, Porcelain | 0000000 | 00000 |
Surface Fillers for Plastic
Use these two-part fillers to rebuild cracked or worn plastic surfaces. The size listed is the combined total of the two parts.
Surface fillers in a cartridge come with a mixer nozzle, but require a gun (sold separately) for dispensing. For best results, use a primer (sold separately).
Container | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Size | Type | Begins to Harden | Reaches Full Strength | Consistency | Mix Ratio | Approx. Coverage @ Thick. | Temp. Range, °F | Color | Finishing Method | For Use On | Each | |
Surface Fillers | ||||||||||||
| 1.7 fl. oz. | Cartridge | 5 min. | 30 min. | Thick Liquid | 1:1 | 11 sq. in. @ 1/4" | -20° to 180° | Gray | Sand | Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Polyethylene Plastic, Polypropylene Plastic | 0000000 | 000000 |
| 1.7 fl. oz. | Cartridge | 20 sec. | 60 min. | Thick Liquid | 1:1 | 11 sq. in. @ 1/4" | -20° to 180° | Amber | Sand | Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Polyethylene Plastic, Polypropylene Plastic | 0000000 | 00000 |
| 1.7 fl. oz. | Cartridge | 50 sec. | 60 min. | Thick Liquid | 1:1 | 11 sq. in. @ 1/4" | -20° to 180° | Black | Sand | Polystyrene Plastic, Polycarbonate Plastic, Polyurethane Rubber, ABS Plastic, PVC Plastic, CPVC Plastic, PETG Plastic, PVDF Plastic, Polyimide Plastic, Polyethylene Plastic, Polypropylene Plastic | 0000000 | 00000 |