Thicker, more pliable, and less aggressive than standard nylon mesh quick-change discs, use these for finer sanding on curved surfaces.

A special fastener on the back of these discs allows you to easily swap one disc for another.

Used for heavy cleaning and stripping, these discs have an abrasive-embedded nylon mesh construction that gives you more control over sanding pressure.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Used for stripping, these discs eliminate discoloration from heat buildup.

Fit these discs over your tool's arbor to sand aluminum, soft metals, and nonmetals.

Holes allow dust removal when used with a vacuum sander.

The thick, abrasive-embedded nylon mesh construction gives you maximum control over sanding pressure.

Quickly attach, remove, and reuse these discs with a compatible sanding tool or backup pad.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Holes allow dust removal when used with a vacuum sander.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating more consistent finishes.

With more flaps than standard discs, these last 30-40% longer.

Almost as hard as diamond, these tungsten carbide bits cut through nonmetals without generating heat.

These bonnets won’t leave swirl marks or scratches when polishing waxed surfaces.

Diamond cuts more quickly, lasts longer, and leaves a finer finish than other lapping grains.

The addition of PTFE provides a more slippery, wear-resistant surface than standard Delrin® acetal resin. It’s commonly fabricated into pump components, gears, and bearings.

An economical alternative to Delrin® acetal resin, this acetal copolymer offers similar wear resistance.

A silicone additive gives this material a self-lubricating surface that reduces friction and extends the life of your parts.

This cast nylon 6 material is easier to machine than other types of nylon. It’s comparable to Nylatron and Nycast.

This nylon stays lubricated over time because it’s filled with oil. Use it to fabricate parts for hard-to-reach places where adding lubricants would be difficult.

Because this 6/12 material absorbs less water than standard nylon 6/6, it holds its shape better. It’s often machined into hose fittings and valve components.

With glass reinforcement, this nylon 6/6 material is stronger than standard nylon, plus it can withstand higher temperatures. It’s widely used in high-stress applications, such as caster wheels and automotive parts.

In addition to a low-friction surface that prevents sticking and binding, this tough material is impact and wear resistant to handle the scuffs, scrapes, and strikes that other plastics can’t.

Often used in high-speed, high-precision, and high-impact applications, such as conveyor rollers and bearings, these rods stand up to scratches and scuffs better than our standard UHMW polyethylene rods. Also known as Tivar HPV.

If a chip of this material breaks off, it can be located by metal detectors to reduce contamination risks.

CPVC is just as chemical resistant as standard PVC Type 1 and can handle hotter temperatures up to 200° F.

Practically nonabsorbent, HDPE won't swell when exposed to moisture. It is denser and more rigid than LDPE, plus it's more chemical resistant.

Because ABS maintains its toughness even after thermoforming, it’s often made into storage cases, tote trays, equipment housings, and protective gear.

Known for its electrical insulating properties, this polystyrene is often used for cable connectors, electrical housings, and in microwave applications. It is also known as Rexolite.

Use Noryl PPO for electrical insulating applications where moisture is a concern. It remains dimensionally stable over time, even when temperatures fluctuate.

When moisture-resistant polyester is combined with PTFE, the result is this self-lubricating material. It’s also called Hydex and PBT.

Polycarbonate maintains good impact resistance across a wide temperature range. It's comparable to Lexan, Hyzod, Tuffak, and Makrolon.

This glass-filled PTFE is more rigid than standard PTFE for increased durability in high-stress applications.

Manufactured from Rulon PTFE, a PTFE that's modified with filler material for a super-slippery, impact-resistant surface that resists wear.

Not only does PEEK provide superior wear resistance in repetitive processes, it is also resists wear caused by abrasion. PEEK can be used as a lightweight substitute for metal parts in chemical-processing applications.

A glass filler is added to this this PEEK material to offer increased durability over standard PEEK in high-stress structural applications.

Among the strongest plastic materials we offer, Torlon PAI has a slippery surface that resists wear. Use it to make high-friction compressor parts, bearings, and seals.

Stronger and more rigid than Torlon 4301 and 4203 because they’re filled with glass, these Torlon 5030 rods are also electrical insulators like Torlon 4203.

Stronger than PTFE, PVDF offers good chemical resistance. Comparable to Kynar and Solef, it’s widely used for pump parts, tank liners, and seals.

Often used for circuit-breaker housings, manifolds, and semiconductor components, Ultem PEI offers excellent electrical-insulating properties.

Widely used to make parts that require autoclaving, polysulfone is a hard, rigid material that’s easy to machine and thermoform. It maintains its physical properties when heated, even when exposed to steam.

Often used as gaskets and bearings, this slippery-surface material absorbs virtually no moisture. PCTFE is equivalent to Kel-F and Neoflon.

This extruded acrylic offers similar performance as cast acrylic at a lower cost.

PETG can be formed into complex shapes without sacrificing durability.

These metric washers surpass most other plastic washers when it comes to withstanding chemicals, oil, and grease.

Choose these washers for their adherence to strict military standards for material and construction.

Low moisture absorption and good heat resistance make these metric washers suitable for wet and harsh environments.

These metric washers can withstand temperatures up to 450° or 500° F without degrading.

Also known as shoulder washers.

As you tighten your screw, the rolled collar compresses under the head to create an insulating barrier between a screw shank and a mating surface.

A specially shaped ID grips your screw shank tightly.

These polyurethane washers withstand wet conditions as well as sunlight, ozone, and some chemicals.

Precisely align, level, and adjust spacing on fasteners, shafts, and machinery with these shims, which are color-coded by thickness for easy identification.

Cut plastic, wood, and soft metal such as aluminum, brass, and copper.

A special fastener on the back of these brushes allows you to easily swap one brush for another.

Rigid, partially twisted bristles handle tasks such as edge rounding and removing weld slag, heavy surface contamination, and large burs. Also known as knot-wire brushes.

Remove light-to-medium rust and stains and small burs with these flexible-bristle brushes.

A mounting nut on each side of the arbor lets you use both sides of the brush.

Use on delicate surfaces.

The abrasive lasts longer than that of standard brushes.

Stick these discs onto breather and other circular vents to guard against water and dirt without obstructing flow.

Shield vents on electronic and automotive equipment, such as cell phone microphones, from water, dirt, and debris without blocking them entirely.

Select these bumpers for applications that require specific load capacities. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. Press them into place with the adhesive backing. They're comparable to Bumpon bumpers.

All of these bumpers are reinforced with an embedded washer or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines. Install them with screws.

A ridge on the stem provides a tighter grip than other push-in bumpers. Push the stem into a hole for quick installation. These bumpers are commonly used as feet on instruments and bench-top equipment to keep them from sliding. They're also good as spacers between sheets of material. Also known as stem and grommet bumpers.

Mount these bumpers on a threaded stud. All are reinforced with a steel core or base plate for strength. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces. They're also good for starting and stopping motion on automated machines.

Keep bumpers of various shapes, materials, and mounting styles on hand to solve whatever problems arise.

Twist these bumpers into a threaded hole. Often used as feet, spacers, and vibration dampers, they absorb shock to prevent damage to equipment and surfaces.

These tags have a matte surface so writing won't smudge or rub off accidentally. Write on them with a permanent marker.

Plastic tags withstand mild acids and are more corrosion resistant than metal tags.

Identify acceptable or critical temperatures or pressures at a glance.

Attach these labels to hard hats to provide safety reminders or to identify first-aid personnel.

Made of pure PTFE, this material has a slippery surface that prevents sticking.

Made from PTFE with an EPDM core, these gaskets have added resiliency resulting in a longer product life.

If a piece wears off, fragments as small as 1 mm can be picked up by a metal-detection system to prevent contamination of your process line.

Offering excellent resistance to detergents, hydraulic fluid, and salts, these PTFE gaskets have a corrosion-resistant 316 stainless steel screen to provide inline straining.

These PTFE gaskets are virtually chemically inert.

Made from a blend of PTFE and 316 stainless steel, these gaskets stand up to the harsh chemicals and high pressures and temperatures used in sanitary processes.

Cover holes, fastener heads, and small areas with these shapes.

Protect small parts with these slippery UHMW rings, discs, and squares.

Tape is cut into convenient discs and rectangles.

A good all-around choice, Garolite G-10/FR4 is strong, machinable, and electrically insulating. It meets UL 94 V-0 for flame retardance.

Stronger than Garolite CE with better electrical-insulating properties, Garolite XX is often fabricated into low-cost electrical components.

Garolite CE is often fabricated into parts where high strength is not required.

Frequently called electrical-grade Garolite, this Garolite G-9 is strong, electrically insulating, and arc resistant in dry environments.

Reinforce structures with these rods—they weigh less than aluminum while remaining strong and almost as rigid.

An alternative to wood in structural applications, FRP fiberglass is strong and lightweight.