Bolt two same-size flanges together with a gasket to create an access point within a line. They are also known as Pressure Class 150 flanges. They have thick, strong walls to handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation.

Use for pressures up to 200 psi. Also known as insert fittings, these slide into semi-flexible plastic pipe and secure with a clamp.

Bolt two same-size flanges together with a gasket to create an access point within a line. They are also known as Pressure Class 150 flanges. Use in high-temperature plumbing and water supply applications up to 200° F.

Use these plastic fittings to connect gasoline fuel lines to machines and equipment. They have excellent corrosion resistance as well as high strength and impact resistance.

Use these polypropylene flanges in outdoor environments—they resist the damaging effects of ultraviolet light. They have the chemical resistance to stand up to acids, solvents, and other harsh substances. Bolt two same-size flanges together with a gasket to create an access point within a line. Flanges are also known as Pressure Class 150 flanges.

Extreme temperatures are no problem for these fittings—they’re made of PTFE, so they can withstand a wider temperature range than any of our other plastic pipe fittings for chemicals. They are commonly used in high-purity chemical flow processes, such as semiconductor and clean room applications.

Flanges have excellent corrosion resistance to handle a wide range of acids and other highly-corrosive chemicals. Use in metal surface treating applications, plating solution lines, and other chemical process applications. They are reinforced with fiberglass layers for better strength and durability than any of our other pipe flanges for chemicals. Bolt two same-size flanges together with a gasket to create an access point within a line.

These Schedule 40 fittings are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

The snap-together design allows you to quickly connect these fittings to pipe with no cement required. Fittings are typically used in gravity-flow drainage applications.

Made of brass, these fittings have good corrosion resistance.

Use at pressures up to 150 psi.

Minimize leaks in your line—these fittings have a single barb that creates a smooth clamping surface for extra-tight connections.

A built-in shut-off valve stops the flow when the coupling is separated, so there’s no need to worry about air or water spilling from your line. Couplings are plastic, which is lighter in weight than metal couplings.

These fittings keep their strength in moist environments and meet NSF/ANSI 61 for drinking water. Also known as instant fittings.

Use these nuts with brass compression fittings to create a seal on plastic tubing. They meet NSF/ANSI 61 for use with drinking water.

These quick-disconnect couplings meet NSF/ANSI 169 for food equipment.

Also known as instant fittings, these chemical-resistant plastic fittings connect to tubing with a push, and an internal gripping ring and fluoroelastomer O-ring hold the tubing tight.

Fittings have a sleeve that bites into tubing as you tighten the nut to form a seal in applications up to 120 psi. Also known as flareless fittings.

Made of polypropylene, these cam-and-groove couplings are lighter in weight than metal cam-and-groove hose couplings.

Couplings are plastic, which is lighter in weight than metal cam-and-groove hose couplings. They consist of a plug and a socket that connect and disconnect quickly. Use them if you need frequent access to a line. To connect, insert the plug into the socket and push the levers down.

Use these dust caps and plugs to keep contaminants out of your hose line.

Couplings consist of a plug and a socket that connect more quickly than threaded garden hose couplings. To connect, push the plug into the socket. The compact design makes these couplings sleeker and easier to handle than cam-and-groove garden hose couplings.

Couplings are made of FDA listed materials, so they’re suitable for food and beverage applications and won’t impart tastes or odors to the product. They consist of a plug and a socket that connect and disconnect quickly. Use them if you need frequent access to a line. To connect, insert the plug into the socket and push the levers down.

Couplings are compatible with quick-disconnect Plastic-shape plugs and sockets. They are designed for food and beverage applications and won’t impart tastes or odors to the product. They consist of a plug and a socket that connect and disconnect quickly so you can frequently access your line. Use at pressures up to 100 psi.

Instead of tossing Ethernet cords with a broken locking tab on their RJ45 plug, fix them with these clips.

Designed to withstand washdown and outdoor environments, these connectors have a seal to block out water and debris.

Turn a single outlet into five outlets with ground fault protection to minimize the risk of electric shock.

Save energy by automatically turning off unused outlets. The master outlet controls five outlets and shuts off power to the other outlets when a device plugged into the master is turned off.

A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.

These curved outlet strips clamp onto a pole or table leg.

Hardwire one of these converters to an extension cord to keep personnel safe from electric shock.

Keep cords tangle-free and ready to use.

Add grounding or surge suppression protection.

Minimize the risk of electric shock by adding ground fault protection to a standard outlet.

Cover unused electrical outlets or plug prongs to protect them from dust, dirt, liquids, and other contaminants.

Inspect the terminal block and wiring without opening the cover.

Keep hollow tapered plugs of various sizes on hand to solve whatever problems arise. The hollow construction allows these plugs to compress for a snug fit in threaded and unthreaded holes of varying diameters.

Pull the two built-in rings to quickly remove these plugs. All are tapered to fit a range of hole diameters.

Sized to fit small openings, these tiny plugs fit snugly but can be removed easily using the flange. They withstand temperatures up to 470° F, which makes them good for electroplating, paint baking, and powder-coating applications. All are tapered to fit a range of hole diameters.

With a surface resistivity of less than 10⁵ ohms, these plugs not only dissipate electrical charges, but can be used as an electrical shield.

Keep equipment safe from electrical currents with these plugs that have a surface resistivity of less than 10¹² ohms.

Seal tube and hose fittings to keep their straight threads protected from contaminants during fabrication and storage.

Safeguard internally threaded BSPT connections from contaminants during fabrication and storage.

Push these plugs into an opening and friction holds them in place.

Flexible ridges securely hold these plugs in place and allow them to fit a range of hole sizes.

Vents in the top allow air circulation and permit heat and fumes to escape. These plugs have tapered prongs that snap into the hole to securely hold them in place.

These plugs are see-through to provide visibility and light transmission. They have wings that expand against the sides of the hole to lock them in place.

The wings on these plugs expand against the sides of a hole to form a liquid-tight seal. Pierce the plugs with round wire, cable, or tubing and they function as a grommet to create insulated holes.

Made of rigid plastic, these caps are more wear resistant than vinyl caps but not as flexible.

The tethered design allows frequent access to the ends of pipe, tubing, and other round objects without ever misplacing the cap.

Commonly used on shipping tubes, these caps have a square head to prevent round objects from rolling during shipping and storage.

Keep equipment safe from electrical currents with these caps that have a surface resistivity of less than 10¹² ohms.

Made of FDA listed materials, these caps are suitable for food contact.

Keep tapered caps of various sizes on hand to solve whatever problems arise. These flexible plastic caps are tapered to fit a variety of unthreaded and threaded objects.

Made of rigid plastic, these caps are more wear resistant than vinyl caps but not as flexible.

Made of rigid plastic, these caps provide more wear resistance to the ends of angle iron than vinyl caps but are not as flexible.

Guard the corners of fragile materials such as glass and mirrors.

Slide these flexible vinyl caps on and they conform for a snug fit. Pull the tab for easy removal.

Similar to a shower cap, these caps have an elastic band that allows them to stretch and cover a variety of shapes in a range of sizes.

Designed for propane tanks such as those on forklifts and grills, these caps protect tank valves during storage and transit. Push the caps onto the valves, then tear their tab to break the seal for easy removal.

Sized to fit hex nuts, these caps snap on for a tight hold and provide protection from corrosion.

To conceal and protect the entire screw head, insert your screw through the hole in the base and snap on the top.

Stretch these caps over flared edges such as flanged tubing and valve handles.

Snap these caps into flange bolt holes to safeguard pipe flanges during shipping, storing, and finishing applications. They all have a thick center pad to protect the flange opening and pipe threads from damage.

Turn the square head of the plug into the sealing ring to close off pipe openings.

Use these vents to maintain consistent pressure as temperatures fluctuate by allowing air to flow through sealed enclosures.

These vents have louvers with foam filters to keep out dust and falling liquids.

No threaded hole or tools needed—snap these vents into enclosures with a maximum 1/8” panel thickness to let airflow in and keep water out even when submerged.

Mount to the outside of your enclosure to prevent moisture from being trapped inside.

Mount these drains at the bottom of your enclosure to let moisture drip out and keep electronics dry.

Give switches and outlets a finished look.

Cover existing outlets and switches for a refreshed appearance, no rewiring necessary.

Snap end and center sections together to create your own two-device or wider wall plate.

Create various data connector configurations by choosing adapters to snap into the ports in these wall plates.

Able to withstand temperatures up to 300° F, these grips are also corrosion- and chemical-resistant.

These 90° elbows absorb less water and are less likely to crack or corrode than other types of plastics and metals.

Vent air from your enclosure to equalize pressure and stop condensation from forming inside while securing cords in wet environments. These polyamide grips are lightweight and resist rusting.

Snap these cord grips into place to secure cable in wet environments.