An economical alternative to our quick-connect clamp-on option, these splices are as quick to install but harder to adjust. Push wire into each end without the need for an installation tool. The splices have a test socket to safely test the voltage after installation.

Install and service setups for two, three, and five wires, then reuse these connectors later. They pop on and off wire with the flip of a clamp to save time over crimping. Choose them for setups that change often, such as prototypes and testing. They even have test sockets to safely test voltage after installation. The assortments include DIN-rail adapters so you can snap connectors into a control panel.

A gel filler seals out water to keep your wires completely dry and conductive. No need to strip your wire—insert insulated wires into the splice, then squeeze the button with a crimper or pliers until it clicks. The splice bites through the insulation, so you don't take extra time or risk nicks and cuts from a wire stripper. Snap splices together to create the exact setup you need.

Flip a clamp onto your wire instead of crimping to speed up installations and reuse your splice later. Choose these splices for setups that change often, such as prototypes and testing. They even have test sockets to safely test voltage after installation.

Flip a clamp onto your wire instead of crimping to speed up installations, then reuse these connectors later. The clamp secures and disconnects wires without damaging them. Choose these connectors for setups that change often, such as prototypes and testing. They even have test sockets to safely test voltage after installation.

DIN Rail Mounting Adapters—Clip connectors onto DIN 3 rail to keep them organized and easily accessible.

Covers—Seal out moisture to protect your connection. Covers are lined with a sticky gel, so you don't need to mix or pour a potting compound yourself. They’re rated IP08 to withstand splashes, rain, and humidity. To repair or expand your circuit, open the cover and remove the wires so you can reuse them. However, you'll need to replace the splice and cover after you open the cover and remove the gel.

Connect two components with different wire sizes, such as an air compressor and its control panel. Also known as step-down splices, these splices join a larger wire and a smaller wire end to end. The larger and smaller openings are color coded so you don't have to measure and mark them yourself. You can snap splices together to create the exact setup you need.

A gel filler seals out water to keep your wires completely dry and conductive. No need to strip your wire—insert insulated wires into the splice, then squeeze the button with a crimper or pair of pliers until it clicks. The splice bites through the insulation, so you don't take extra time or risk nicks and cuts from a wire stripper.

Install and service setups for two to eight wires. These assortments include DIN-rail adapters so you can snap connectors into a control panel. Quick-connect push-on connectors are as fast to install as our clamp-on option, though they're not as easy to adjust. Push wire into place without the need for an installation tool. To break the connection later, you'll have to pull wire back out. The connectors also have test sockets to safely test voltage after installation.

The choice for outdoor electrical panels, HVAC systems, and anywhere you're concerned about moisture. A gel filler repels moisture to keep your wires dry and conductive.

These connectors bite through insulation, so you save time and avoid damage from a wire stripper. For the most dependable connection, use a crimping tool to squeeze connectors onto your wire.

These connectors are as quick to install as our clamp-on option, though they're not as easy to adjust. They extend or terminate electrical connections in branch circuits, such as light fixtures and electronic devices. Push wire into place without the need for an installation tool. To break the connection later, you'll have to pull wire back out. The connectors also have test sockets to safely test voltage after installation.

DIN Rail Mounting Adapters—Clip connectors onto DIN 3 rail to keep them organized and easily accessible.

Covers—Seal out moisture to protect your connection. Covers are lined with a sticky gel, so you don't need to mix or pour a potting compound yourself. They’re rated IP08 to withstand splashes, rain, and humidity. To repair or expand your circuit, open the cover and remove the wires so you can reuse them. However, you'll need to replace the splice and cover after you open the cover and remove the gel.