McMaster-Carr logo
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    73 Products

    Tire Pressure and Inflator Test Gauges

    Image of Product. Front orientation. Contains Inset. Tire Pressure Test Gauges. Tire Pressure and Inflator Test Gauges.
    Test the accuracy of tire pressure gauges and tire inflation gauges. Designed to higher accuracy standards than typical tire gauges, these calibrators are not meant to be used to regularly check tire pressure directly. Instead, they serve as an objective reference to eliminate inaccuracies and discrepancies between your gauges. To use, check tire pressure first using the calibrator and then again with your tire pressure gauge. Make calibration adjustments to your gauge until its reading matches the reading on the calibrator.
    Head
    Type
    No. of
    Heads
    Pressure Range
    Pressure Numeric
    Increments, psi
    Accuracy
    Overall
    Lg.
    Dial
    Dia.
    Material
    Features
    Each
    Dial Readout
    Angled210 psi to 120 psi
    100 kPa to 900 kPa    		2±1 psi11 1/2"3/4"Chrome-Plated BrassBleed Valve7554N11000000
     

    Tire Gauges with Dial

    Image of Product. Front orientation. Tire Gauges. Tire Gauges with Dial, Style B.

    Style B

    View pressure readings on a numbered dial.
    Rubber Sleeve—Gauges with a rubber sleeve prevent metal-to-metal contact with your tire to avoid damaging it.
    Style
    Head
    Type
    No. of
    Heads
    Pressure Range
    Pressure Numeric
    Increments, psi
    Accuracy
    Overall
    Lg.
    Dial
    Dia.
    Material
    Case
    Material
    Features
    Each
    BAngled10 psi to 120 psi, 0 kPa to 800 kPa2±3%4 3/4"2 1/2"Nickel-Plated BrassRubberRubber Sleeve, Tread Depth Gauge6654A101000000

    Pressure Transmitters

    Remotely monitor pressure in general purpose applications such as pumping and compressing systems. These transmitters, also known as transducers, convert pressure to an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls. For your receiving device to interpret the signal from the transmitter, you will need to calibrate it for the transmitter's pressure range and output signal. As pressure increases, the output signal from the transmitter will increase. Transmitters will only provide accurate readings within the rated pressure range.
    Transmitters are rated NEMA 4X and IP65 or IP67 and are good for washdown and corrosive environments.
    4 mA to 20 mA Output Signal—Wire Lead Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 4 mA to 20 mA Output Signal—Wire Lead Connection.
    Transmitters with output current connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 361 15/16"15/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K5620000000
     
    4 mA to 20 mA Output Signal—4-Pole M12 Plug Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 4 mA to 20 mA Output Signal—4-Pole M12 Plug Connection.
    Transmitters with output current connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    Transmitters with a M12 plug connection are compatible with M12 connectors.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 361 11/16"15/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K1230000000
     
    4 mA to 20 mA Output Signal—DIN A Wire Connection
    Image of Product. Front orientation. Pressure Transmitters. Pressure Transmitters, 4 mA to 20 mA Output Signal—DIN A Wire Connection.
    Transmitters with output current connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 36PG-9
    		3 7/16"1 5/16"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K6020000000
     
    4 mA to 20 mA Output Signal—DIN C Wire Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 4 mA to 20 mA Output Signal—DIN C Wire Connection.
    Transmitters with output current connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    Pressure Transmitters with Calibration Certificate Traceable to NIST—Transmitters with calibration certificate traceable to NIST include documentation that states they've passed a test for accuracy.
    Pressure
    Transmitters
    Pressure Transmitters with Calibration
    Certificate Traceable to NIST
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
    Each
     
    1/8 NPT Male Pipe Connection
    0 to 60601209 to 36PG-7
    		2 5/8"1 3/8"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K3790000000———0
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 36PG-7
    		2 5/8"1 3/8"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K540000003196K740000000
     
    4 mA to 20 mA Output Signal—Aptiv MP 150 Plug Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 4 mA to 20 mA Output Signal—Aptiv MP 150 Plug Connection.
    Transmitters with output current connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 362 1/16"1 1/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K4430000000
     
    4 mA to 20 mA Output Signal—3-Pole DT Deutsch Style Plug Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 4 mA to 20 mA Output Signal—3-Pole DT Deutsch Style Plug Connection.
    Transmitters with output current connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 362 1/16"1 1/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K4560000000
     
    0V DC to 5V DC Output Signal—4-Pole Wire Lead Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 0V DC to 5V DC Output Signal—4-Pole Wire Lead Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 361 15/16"15/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K5180000000
     
    1V DC to 5V DC Output Signal—Wire Lead Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 1V DC to 5V DC Output Signal—Wire Lead Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 361 15/16"15/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K5330000000
     
    1V DC to 5V DC Output Signal—4-Pole M12 Plug Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 1V DC to 5V DC Output Signal—4-Pole M12 Plug Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Transmitters with a M12 plug connection are compatible with M12 connectors.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 361 11/16"7/8"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K5040000000
     
    1V DC to 5V DC Output Signal—DIN A Wire Connection
    Image of Product. Front orientation. Pressure Transmitters. Pressure Transmitters, 1V DC to 5V DC Output Signal—DIN A Wire Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 36PG-9
    		3 7/16"1 5/16"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K5750000000
     
    1V DC to 5V DC Output Signal—DIN C Wire Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 1V DC to 5V DC Output Signal—DIN C Wire Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 60601209 to 36PG-7
    		2 5/8"1 3/8"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K3390000000
     
    0V DC to 10V DC Output Signal—Wire Lead Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 0V DC to 10V DC Output Signal—Wire Lead Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 606012014 to 361 15/16"15/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K5470000000
     
    0V DC to 10V DC Output Signal—4-Pole M12 Plug Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 0V DC to 10V DC Output Signal—4-Pole M12 Plug Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Transmitters with a M12 plug connection are compatible with M12 connectors.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 606012014 to 361 11/16"15/16"IP67, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K3260000000
     
    0V DC to 10V DC Output Signal—DIN A Wire Connection
    Image of Product. Front orientation. Pressure Transmitters. Pressure Transmitters, 0V DC to 10V DC Output Signal—DIN A Wire Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 606012014 to 36PG-9
    		3 7/16"1 5/16"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K5880000000
     
    0V DC to 10V DC Output Signal—DIN C Wire Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters, 0V DC to 10V DC Output Signal—DIN C Wire Connection.
    Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    Pressure Transmitters with Calibration Certificate Traceable to NIST—Transmitters with calibration certificate traceable to NIST include documentation that states they've passed a test for accuracy.
    Pressure
    Transmitters
    Pressure Transmitters with Calibration
    Certificate Traceable to NIST
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 606012014 to 36PG-7
    		2 5/8"1 3/8"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Air
    Argon
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Nitrogen
    Water    		±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553196K20400000003196K940000000
     

    Inflator Tire Gauges

    Mate these gauges to a compressed air line to measure pressure while inflating tires. They are strong enough to stand up to constant use.
    Indicator Bar Readout
    Image of Product. Front orientation. Tire Gauges. Inflator Tire Gauges, Indicator Bar Readout, Angled Head, 1 Head.
    Image of Product. Front orientation. Tire Gauges. Inflator Tire Gauges, Indicator Bar Readout, Angled Head, 2 Heads.
    Image of Product. With One Straight Head. Front orientation. Tire Gauges. Inflator Tire Gauges, Indicator Bar Readout, Straight Head, 1 Head.

    Angled Head

    1 Head

    Angled Head

    2 Heads

    With One Straight Head

    Indicator bar readouts slide out of the top of the gauge to display pressure readings.
    Tire Gauges
    Replacement Hose
    Hose
    Air Inlet
    Air
    Outlet
    Head
    Type
    No. of
    Heads
    Pressure Range
    Pressure Numeric
    Increments, psi
    Indicator
    Bar Material
    Lg.
    Material
    Connection
    Port
    Pipe
    Size
    Thread
    Type
    Thread
    Size
    Thread
    Type
    Schrader Valve
    Connection Type
    Each
    Each
    Aluminum
    Angled110 psi to 120 psi, 80 kPa to 840 kPa2Plastic12"Rubber
    		Pipe1/4
    		NPT
    		0.305"-32
    		Schrader
    		Press-and-Hold6113A11000000———0
    Angled210 psi to 120 psi, 80 kPa to 840 kPa2Plastic12"Rubber
    		Pipe1/4
    		NPT
    		0.305"-32
    		Schrader
    		Press-and-Hold6113A12000006647A13000000
    Straight110 psi to 120 psi, 80 kPa to 840 kPa2Plastic12"Rubber
    		Pipe1/4
    		NPT
    		0.305"-32
    		Schrader
    		Press-and-Hold6647A1400000———0
     

    Pressure and Vacuum Transmitters

    Monitor and control vacuum pumps, air compressors, and hydraulics. These transmitters convert both pressure and vacuum into an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls. As pressure increases, the output signal from the transmitter will increase. For your receiving device to interpret the signal from the transmitter, you will need to calibrate it for the transmitter's pressure or vacuum range and output signal. Transmitters will only provide accurate readings within the rated pressure or vacuum range. All transmitters are rated NEMA 4X for use in washdown and corrosive environments.
    4 mA to 20 mA Output Signal—Wire Leads
    Image of Product. Front orientation. Contains Annotated. Pressure and Vacuum Transmitters. Pressure and Vacuum Transmitters, Wire Lead Connection.
    Transmitters with current output connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    IP67 Enclosure Rating—IP67 rated transmitters are protected from temporary submersion during washdowns.
    Max.
    Pressure, psi
    Pressure
    Range, psi
    Vacuum Range,
    in. Hg
    Continuous
    Short-Term
    Input Voltage,
    V DC
    Pipe Size
    Ht.
    Wd.
    Enclosure
    Rating
    For Use With
    Accuracy
    Temp. Range,
    ° F
    Connection
    Material
    Each
    Glass-Filled Nylon Housing
    0 to 600 to 301201209 to 361/4 NPT Male1 15/16"15/16"IP67, NEMA 4X
    		Air, Argon, Diesel Fuel, Gasoline, Hydraulic Fluid, Nitrogen, Water±1.0%-40 to 255304 Stainless Steel2957N130000000
     
    4 mA to 20 mA Output Signal—4-Pole M12 Plug-In Connection
    Image of Product. Front orientation. Contains Annotated. Pressure and Vacuum Transmitters. Pressure and Vacuum Transmitters, M12 Connection.
    Transmitters with current output connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    IP67 Enclosure Rating—IP67 rated transmitters are protected from temporary submersion during washdowns.
    Max.
    Pressure, psi
    Pressure
    Range, psi
    Vacuum Range,
    in. Hg
    Continuous
    Short-Term
    Input Voltage,
    V DC
    Pipe Size
    Ht.
    Wd.
    Enclosure
    Rating
    For Use With
    Accuracy
    Temp. Range,
    ° F
    Connection
    Material
    Each
    Glass-Filled Nylon Housing
    0 to 600 to 301201209 to 361/4 NPT Male1 11/16"7/8"IP67, NEMA 4X
    		Air, Argon, Diesel Fuel, Gasoline, Hydraulic Fluid, Nitrogen, Water±1.0%-40 to 255304 Stainless Steel4674N20000000
     
    4 mA to 20 mA Output Signal—DIN C Connection
    Image of Product. Front orientation. Contains Annotated. Pressure and Vacuum Transmitters. Pressure and Vacuum Transmitters, DIN C Connection.
    Transmitters with current output connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    IP65 Enclosure Rating—IP65 rated transmitters are protected from dust and low-pressure jets of water.
    Max.
    Pressure, psi
    Pressure
    Range, psi
    Vacuum Range,
    in. Hg
    Continuous
    Short-Term
    Input Voltage,
    V DC
    Pipe Size
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    For Use With
    Accuracy
    Temp. Range,
    ° F
    Connection
    Material
    Each
    Glass-Filled Nylon Housing
    0 to 600 to 301201209 to 361/4 NPT MalePG-7
    		2 1/2"15/16"IP65, NEMA 4X
    		Air, Argon, Diesel Fuel, Gasoline, Hydraulic Fluid, Nitrogen, Water±1.0%-40 to 255304 Stainless Steel4674N1520000000
     
    1V DC to 5V DC Output Signal—Wire Leads
    Image of Product. Front orientation. Contains Annotated. Pressure and Vacuum Transmitters. Pressure and Vacuum Transmitters, Wire Lead Connection.
    Transmitters with voltage output connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    IP67 Enclosure Rating—IP67 rated transmitters are protected from temporary submersion during washdowns.
    Max.
    Pressure, psi
    Pressure
    Range, psi
    Vacuum Range,
    in. Hg
    Continuous
    Short-Term
    Input Voltage,
    V DC
    Pipe Size
    Ht.
    Wd.
    Enclosure
    Rating
    For Use With
    Accuracy
    Temp. Range,
    ° F
    Connection
    Material
    Each
    Glass-Filled Nylon Housing
    0 to 600 to 301201209 to 361/4 NPT Male1 15/16"15/16"IP67, NEMA 4X
    		Air, Argon, Diesel Fuel, Gasoline, Hydraulic Fluid, Nitrogen, Water±1.0%-40 to 255304 Stainless Steel4674N3570000000
     
    0V DC to 10V DC Output Signal—Wire Leads
    Image of Product. Front orientation. Contains Annotated. Pressure and Vacuum Transmitters. Pressure and Vacuum Transmitters, Wire Lead Connection.
    Transmitters with voltage output connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    IP67 Enclosure Rating—IP67 rated transmitters are protected from temporary submersion during washdowns.
    Max.
    Pressure, psi
    Pressure
    Range, psi
    Vacuum Range,
    in. Hg
    Continuous
    Short-Term
    Input Voltage,
    V DC
    Pipe Size
    Ht.
    Wd.
    Enclosure
    Rating
    For Use With
    Accuracy
    Temp. Range,
    ° F
    Connection
    Material
    Each
    Glass-Filled Nylon Housing
    0 to 600 to 3012012014 to 361/4 NPT Male1 15/16"15/16"IP67, NEMA 4X
    		Air, Argon, Diesel Fuel, Gasoline, Hydraulic Fluid, Nitrogen, Water±1.0%-40 to 255304 Stainless Steel4674N3470000000
     
    0V DC to 10V DC Output Signal—DIN C Connection
    Image of Product. Front orientation. Contains Annotated. Pressure and Vacuum Transmitters. Pressure and Vacuum Transmitters, DIN C Connection.
    Transmitters with voltage output connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    IP65 Enclosure Rating—IP65 rated transmitters are protected from dust and low-pressure jets of water.
    Max.
    Pressure, psi
    Pressure
    Range, psi
    Vacuum Range,
    in. Hg
    Continuous
    Short-Term
    Input Voltage,
    V DC
    Pipe Size
    Electrical Connection
    Thread Size
    Ht.
    Wd.
    Enclosure
    Rating
    For Use With
    Accuracy
    Temp. Range,
    ° F
    Connection
    Material
    Each
    Glass-Filled Nylon Housing
    0 to 600 to 3012012014 to 361/4 NPT MalePG-7
    		2 1/2"15/16"IP65, NEMA 4X
    		Air, Argon, Diesel Fuel, Gasoline, Hydraulic Fluid, Nitrogen, Water±1.0%-40 to 255304 Stainless Steel4674N1440000000
     

    Pressure-Regulating Valves for Water, Oil, Air, and Inert Gas

    Image of Product. Valves with Buna-N Diaphragm. Front orientation. Pressure-Regulating Valves. Pressure-Regulating Valves for Water, Oil, Air, and Inert Gas, Female Inlet, Buna-N Diaphragm, Brass Body.
    Image of Product. Valves with Buna-N Diaphragm and Gauge Port. Front orientation. Pressure-Regulating Valves. Pressure-Regulating Valves for Water, Oil, Air, and Inert Gas, Female Inlet, Buna-N Diaphragm, Brass Body, NPT.

    Valves with

    Buna-N

    Diaphragm

    Valves with

    Buna-N

    Diaphragm

    and Gauge

    Port

    These valves automatically reduce a high, variable inlet pressure to a lower, stable outlet pressure. Adjust the outlet pressure within the range.
    Internal Strainer—Internal strainers trap debris.
    Pressure-Regulating Valves with 1/4 NPT Gauge Port—Gauge ports let you attach a pressure gauge to monitor outlet pressure.
    Inlet
    Outlet
    Pressure-Regulating
    Valves
    Pressure-Regulating Valves
    with 1/4 NPT Gauge Port
    Pipe
    Size
    Location
    Max. Pressure,
    psi
    Pipe
    Size
    Location
    End-to-End
    Lg.
    For Use With
    Temp. Range,
    ° F
    Outlet Pressure,
    psi
    Each
    Each
    NPT Female
     
    Brass Body—Buna-N Diaphragm and Seal with Internal Strainer
    1/4
    		Side2501/4
    		Side2 1/4"Water, Oil, Air, Inert Gas32 to 18080 to 1204677K5100000004677K610000000
    3/8
    		Side2503/8
    		Side2 1/4"Water, Oil, Air, Inert Gas32 to 18080 to 1204677K550000004677K65000000
     

    Compressed Air Regulators for Tubing

    Use these regulators to adjust and maintain the pressure of your tubing air lines. Install them in your air line after filters.
    Relieving Regulators
    Image of Product. Front orientation. Compressed Air Regulators. Compressed Air Regulators for Tubing, Relieving Regulators, Push to Connect with Gauge Not Included.

    Push to

    Connect with

    Gauge Not

    Included

    Relieving regulators exhaust when the downstream pressure exceeds the set pressure.
    Panel-Mount Nut—Install regulators with a panel-mount nut through a hole in your panel or enclosure. Their knob remains accessible, while the air line is protected behind the panel.
    Mounting Brackets—Mounting brackets (sold separately) allow you to attach the regulator to a wall or equipment.
    Regulators
    Mounting
    Brackets
    For
    Tube OD
    Overall
    Inlet
    Outlet
    Max. Flow Rate
    @ Pressure
    Max. Pressure,
    psi
    Wd.
    Ht.
    Housing
    Material
    Max. Temp.,
    ° F
    Includes
    Regulating
    Accuracy
    Pressure Regulation,
    psi
    Each
    Each
    Push to Connect with Gauge Not Included
    1/4"1/4"5.3 scfm @ 100 psi1451 7/8"2 1/8"Acetal140Panel-Mount Nut±3 psi15 to 1208844K110000008844K2100000
    5/16"5/16"9.1 scfm @ 100 psi1452 1/4"2 3/8"Acetal140Panel-Mount Nut±3 psi15 to 1208844K12000008844K210000
    3/8"3/8"10 scfm @ 100 psi1452 1/2"2 5/8"Acetal140Panel-Mount Nut±7 psi15 to 1208844K10900000———0
    6 mm6 mm5.3 scfm @ 100 psi1451 7/8"2 1/8"Acetal140Panel-Mount Nut±3 psi15 to 1208844K13000008844K210000
    10 mm10 mm10 scfm @ 100 psi1452 1/2"2 5/8"Acetal140Panel-Mount Nut±7 psi15 to 1208844K11100000———0
     

    Differential Pressure Transmitters for Liquids

    Used with pumps, cooling systems, and other liquid applications, these transmitters remotely measure the difference in pressure between two inputs. They are also known as transducers. These transmitters convert differential pressure to an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls to monitor pressure or control equipment. You’ll often see them used to indicate a filter is clogged.
    For your receiving device to interpret the signal from the transmitter, you will need to calibrate it for the transmitter's differential pressure range and output signal. Transmitters will only provide accurate readings within the rated pressure range. Connect them using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    316 Stainless Steel HousingAbout 316 Stainless Steel Housing
    Image of Product. Front orientation. Contains Annotated. Differential Pressure Transmitters. Differential Pressure Transmitters for Liquids, 316 Stainless Steel Housing.
    IP66 Enclosure Rating— IP66 rated transmitters are dust tight and protect against washdowns.
    NEMA 4X Enclosure Rating—NEMA 4X rated transmitters protect against weather, washdowns, and corrosion.
    Mounting
    Holes
    Connection
    Pressure Differential,
    psi
    Max. Input
    Pressure, psi
    Input Voltage,
    V DC
    Pipe
    Size
    For No.
    of Wires
    Mounting Hardware
    Included
    Dia.
    No.
    of
    Ht.
    Wd.
    Certification
    Enclosure
    Rating
    For Use With
    Accuracy
    Pipe
    Fitting
    Material
    Temp. Range,
    ° F
    Each
    4 to 20 mA Output Signal—Screw Terminals
    0 to 2512010 to 351/4
    		2No1/4"22"1 7/16"CE Marked
    		IP66, NEMA 4X
    		Diesel Fuel, Gasoline, Hydraulic Fluid, Water±0.5%NPT FemaleThreaded
    		316 Stainless Steel
    		0 to 2003257N130000000
     

    Compact Precision Compressed Air Regulators

    Image of Product. Front orientation. Compressed Air Regulators. Compact Precision Compressed Air Regulators.
    Fit these regulators in tight spaces to adjust and maintain air pressure in sensitive applications where constant, consistent pressure is important to generate precise force and movement. All are relieving regulators, so they exhaust when the downstream pressure exceeds the set pressure. Install them in your air line after filters.
    Relieving Regulators
    BSPP Inlet Thread—BSPP threads are also known as G threads.
    Mounting Brackets—Mounting brackets (sold separately) allow you to attach the regulator to a wall or equipment.
    Regulators
    Mounting
    Brackets
    Pipe
    Size
    Overall
    Inlet
    Outlet
    Max. Flow Rate
    @ Pressure
    Max. Pressure,
    psi
    Gauge
    Included
    No. of Gauge
    Ports
    Wd.
    Ht.
    Housing
    Material
    Max. Temp.,
    ° F
    Pressure Regulation,
    psi
    Each
    Each
    NPT Female Inlet × NPT Female Outlet
     
    ±0.3% Regulating Accuracy
    1/8
    		1/8
    		14 scfm @ 100 psi150No21 3/8"3 7/8"Aluminum1601 to 1202227T200000002227T41000000
     
    BSPP Female Inlet × BSPP Female Outlet
     
    ±0.3% Regulating Accuracy
    1/8
    		1/8
    		14 scfm @ 100 psi150No21 3/8"3 7/8"Aluminum1601 to 1202490T10000002227T4100000
     
    Pressure Gauges
    Image of Product. Front orientation. Pressure Gauges. Compact Precision Compressed Air Regulators.
    Choose a Pressure, psi
    Each
    NPT Thread
    1 to 30, 1 to 60, 1 to 1202227T4000000
     
    BSPP Thread
    1 to 30, 1 to 60, 1 to 1202490T200000
     

    Adjustable-Range Pressure Transmitters

    Image of Product. Top orientation. Pressure Transmitters. Adjustable-Range Pressure Transmitters.
    Fine-tune the pressure range on these transmitters to account for changes in pressure readings over time. With an adjustable range, also known as adjustable zero and adjustable span, the top and bottom of the pressure range can be changed by up to 5%. This saves you from having to make corrections on receiving devices, such as programmable logic controllers (PLCs), remote displays, and motor speed controls. These transmitters, often called transducers, convert pressure to an electrical signal that is interpreted by receiving devices to monitor pressure or control equipment. As pressure increases, the output signal from the transmitter will increase. Transmitters will only provide accurate readings within the rated pressure range.
    Rated NEMA 4X, these transmitters stand up to washdowns and corrosion.
    4 mA to 20 mA Output Signal—Transmitters with output current connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    1V DC to 5V DC Output Signal—Transmitters with output voltage connect using three wires—two wires into the power supply and a separate wire that sends a signal to the receiver. The receiver and the transmitter share a common ground wire back to the power supply.
    ±1% Accuracy
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Pipe
    Size
    Ht.
    Wd.
    Enclosure
    Rating
    For Use With
    Pipe
    Connection
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
    4 mA to 20 mA Output Signal—Wire Lead Connection
    0 to 606012010 to 361/4
    		3"7/8"NEMA 4X
    		Air
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Water    		NPT Male304 Stainless Steel
    		304 Stainless Steel-20 to 18031685K6240000000
     
    1V DC to 5V DC Output Signal—Wire Lead Connection
    0 to 606012010 to 361/4
    		3"7/8"NEMA 4X
    		Air
    Diesel Fuel
    Gasoline
    Hydraulic Fluid
    Water    		NPT Male304 Stainless Steel
    		304 Stainless Steel-20 to 18031685K612000000
     

    Precision Compressed Air Regulators

    Use these regulators in sensitive applications that require constant, consistent pressure for precise force and movement. They’re often used on calibration stands in laboratories or with air-powered clamps that hold delicate items. All are relieving regulators, so they exhaust when the downstream pressure exceeds the set pressure. Install them in your air line after filters.
    Relieving Regulators
    Image of Product. ±0.1% Regulating Accuracy. Front orientation. ±0.1% Regulating Accuracy. Precision Compressed Air Regulators.

    ±0.1%

    Regulating

    Accuracy

    BSPP Inlet Thread—BSPP threads are also known as G threads.
    ±0.1% Regulating Accuracy—Regulators with a ±0.1% accuracy have a sensor and a servo-adjustment mechanism that work together to monitor pressure and instantly adapt to input pressure changes—even when conditions change. They have a locking nut to prevent accidental pressure changes.
    Mounting Brackets—Mounting brackets (sold separately) let you attach the regulator to a wall or equipment.
    Regulators
    Mounting
    Brackets
    Pipe
    Size
    Overall
    Inlet
    Outlet
    Max. Flow Rate
    @ Pressure
    Max. Pressure,
    psi
    Gauge
    Included
    No. of Gauge
    Ports
    Wd.
    Ht.
    Housing
    Material
    Max. Temp.,
    ° F
    Features
    Pressure Regulation,
    psi
    Each
    Each
    NPT Female Inlet × NPT Female Outlet
     
    ±0.1% Regulating Accuracy
    1/8
    		1/8
    		14 scfm @ 100 psi150No12 1/8"4 1/4"Zinc Alloy160Servo-Adjustment Mechanism, Locking Nut2 to 1206162K140000000———0
    1/4
    		1/4
    		14 scfm @ 100 psi150No22 1/8"4 1/4"Zinc Alloy160Servo-Adjustment Mechanism, Locking Nut2 to 1206162K170000006162K42000000
    3/8
    		3/8
    		14 scfm @ 100 psi150No22 1/8"4 1/4"Zinc Alloy160Servo-Adjustment Mechanism, Locking Nut2 to 1206162K180000006162K4200000
     
    BSPP Female Inlet × BSPP Female Outlet
     
    ±0.1% Regulating Accuracy
    1/4
    		1/4
    		14 scfm @ 100 psi150No22 1/8"4 1/4"Zinc Alloy160Servo-Adjustment Mechanism, Locking Nut2 to 1206162K190000006162K4200000
     

    Tire Gauges with Indicator Bar

    A bar slides out of the top of these gauges to display pressure reading.
    1 Angled Head
    Image of Product. Front orientation. Tire Gauges. Tire Gauges with Indicator Bar, 1 Angled Head.
    Pressure Range
    Pressure Numeric
    Increments, psi
    Accuracy
    Overall
    Lg.
    Indicator
    Bar Material
    Features
    Each
    Nickel-Plated Brass
    20 psi to 120 psi, 120 kPa to 820 kPa2±2 psi6"PlasticPocket Clip6637A2200000
     
    1 Angled Head and 1 Straight Head
    Image of Product. Front orientation. Tire Gauges. Tire Gauges with Indicator Bar, 1 Angled Head and 1 Straight Head.
    Pressure Range
    Pressure Numeric
    Increments, psi
    Accuracy
    Overall
    Lg.
    Indicator
    Bar Material
    Features
    Each
    Nickel-Plated Brass
    20 psi to 120 psi, 120 kPa to 820 kPa2±2 psi6 1/2"PlasticPocket Clip6637A23000000
     

    Pressure Transmitters for Oxygen

    Adhere to safety standards and monitor pressure when working with high concentrations of oxygen. These transmitters are cleaned following ASME B40.100 IV guidelines and are sealed in an airtight bag to prevent contamination before use. Also known as transducers, they convert pressure to an electrical signal that can be interpreted by receiving devices, such as remote displays, programmable logic controllers, and motor speed controls. For your receiving device to interpret the signal from the transmitter, you will need to calibrate it for the transmitter's pressure range and output signal. As pressure increases, the output signal from the transmitter will increase. Transmitters will only provide accurate readings within the rated pressure range.
    These transmitters are rated NEMA 4X and IP65 for protection from dust, weather, washdown, and corrosion. UL and C-UL recognized components and CE marked, they also meet American, Canadian, and European safety standards.
    With an output current, they connect using two wires. The same wire is used to send a signal to the receiver and to power the transmitter. Current doesn’t lose signal over long distances and isn’t affected by electrical interference from other devices.
    4 mA to 20 mA Output Signal—Wire Lead Connection
    Image of Product. Front orientation. Contains Annotated. Pressure Transmitters. Pressure Transmitters for Oxygen.
    Pressure
    Range, psi
    Max. Continuous
    Pressure, psi
    Max. Short-Term
    Pressure, psi
    Input Voltage,
    V DC
    Ht.
    Wd.
    Enclosure
    Rating
    Certification
    For Use
    With
    Accuracy
    Housing Material
    Connection
    Material
    Temp. Range,
    ° F
    Each
     
    1/4 NPT Male Pipe Connection
    0 to 601201209 to 362 3/8"1 5/16"IP65, NEMA 4X
    		UL Recognized Component, C-UL Recognized Component, CE Marked
    		Oxygen±1.0%Glass-Filled Nylon304 Stainless Steel-40 to 2553914A120000000
     

    DIN-Mount Electronically-Controlled Precision Compressed Air Regulators

    Image of Product. Front orientation. Compressed Air Regulators. DIN-Mount Electronically-Controlled Precision Compressed Air Regulators.
    Mount these regulators to a 35 mm DIN rail with the included bracket. Designed for control applications that require high reliability and repeatability, they translate electrical signals to output pressure. Use them where you need consistent air pressure to generate precise force and movement. As the input signal current or voltage increases, the output pressure increases proportionally within the regulating range.
    Pair these regulators with sensors that produce the required input signal current or voltage or with programmable logic controllers (PLCs) for automatic setting adjustments. All are relieving regulators, so they exhaust when the downstream pressure exceeds the set pressure. Install them in your air line after your filters.
    Pressure Regulation Range—Regulators with a 0 psi minimum pressure regulation range stop airflow at the minimum electrical signal, allowing you to prevent air from flowing downstream without shutting off the air supply upstream.
    Pipe
    Size
    Overall
    Pressure Regulation
    Range, psi
    Input Analog
    Signal
    Inlet
    Outlet
    Max. Flow Rate
    @ Pressure
    Max. Pressure,
    psi
    Gauge
    Included
    No. of Gauge
    Ports
    For DIN
    Rail Ht., mm
    Wd.
    Ht.
    Housing
    Material
    Max. Temp.,
    ° F
    Electrical
    Connection Type
    Includes
    Each
    NPT Female Inlet × NPT Female Outlet
     
    ±1% Regulating Accuracy—4 mA to 20 mA Input Signal
    0 to 120—1/4
    		1/4
    		12 scfm @ 100 psi150No1351 1/2"5 1/8"Aluminum155HardwireDIN-Rail Mounting Bracket2859T6460000000
     
    ±1% Regulating Accuracy—0V DC to 10V DC Input Signal
    0 to 1200V DC to 10V DC1/4
    		1/4
    		12 scfm @ 100 psi150No1351 1/2"5 1/8"Aluminum155HardwireDIN-Rail Mounting Bracket2859T26000000
     
    ±0.5% Regulating Accuracy—4 mA to 20 mA Input Signal
    3 to 120—1/4
    		1/4
    		12 scfm @ 100 psi150No1351 1/2"3 3/4"Aluminum155HardwireDIN-Rail Mounting Bracket2859T2000000
     
    ±0.5% Regulating Accuracy—0V DC to 10V DC Input Signal
    3 to 1200V DC to 10V DC1/4
    		1/4
    		12 scfm @ 100 psi150No1351 1/2"3 3/4"Aluminum155HardwireDIN-Rail Mounting Bracket2859T3000000
     

    Hazardous Location Electronically-Controlled Precision Compressed Air Regulators

    Image of Product. Front orientation. Compressed Air Regulators. Hazardous Location Electronically-Controlled Precision Compressed Air Regulators.
    Intrinsically safe, these regulators cannot create sparks, so they’re safe to use in NEC Class I, II, and III, Division 1 and 2 hazardous locations. They translate electrical signals into steady output pressure for precise, repeatable motion. As the input signal increases, the output pressure increases proportionally within the regulation range. Pair them with sensors that produce the required input signal current or with programmable logic controllers (PLCs) for automatic setting adjustments. Install them in your air line after filters.
    All are relieving regulators, so they exhaust when the downstream pressure exceeds the set pressure.
    BSPP Inlet Thread—BSPP threads are also known as G threads.
    Pipe
    Size
    Overall
    Pressure Regulation
    Range, psi
    Input Analog
    Signal
    Inlet
    Outlet
    Max. Flow Rate
    @ Pressure
    Max. Pressure,
    psi
    Gauge
    Included
    No. of Gauge
    Ports
    Wd.
    Ht.
    Housing
    Material
    Max. Temp.,
    ° F
    Electrical
    Connection Type
    Includes
    Enclosure
    Rating
    Hazardous Location Rating
    Certification
    Each
    NPT Female Inlet × NPT Female Outlet
     
    ±0.5% Regulating Accuracy
    3 to 1204 mA to 20 mA1/4
    		1/4
    		13.5 scfm @ 100 psi150No13"4 1/4"Aluminum140HardwireMounting BracketNEMA 4X, IP65
    		NEC Class I Divisions 1, 2 Groups C, D; NEC Class II Divisions 1, 2 Groups E, F, G; NEC Class III Divisions 1, 2
    		FM Approved
    		9337N1160000000
     
    BSPP Female Inlet × BSPP Female Outlet
     
    ±0.5% Regulating Accuracy
    3 to 1204 mA to 20 mA1/4
    		1/4
    		13.5 scfm @ 100 psi150No13"4 1/4"Aluminum140HardwireMounting BracketNEMA 4X, IP65
    		NEC Class I Divisions 1, 2 Groups C, D; NEC Class II Divisions 1, 2 Groups E, F, G; NEC Class III Divisions 1, 2
    		FM Approved
    		9337N119000000
     

    Electronically-Controlled Precision Compressed Air Regulators

    Image of Product. Front orientation. Compressed Air Regulators. Electronically-Controlled Precision Compressed Air Regulators.
    Designed for control applications that require high reliability and repeatability, these regulators translate electrical signals to output pressure. As the input signal increases, the output pressure increases proportionally within the regulation range. Use them where consistent pressure is needed to generate precise force and movement. Pair them with sensors that produce the required input signal current or programmable logic controllers (PLC) for automatic setting adjustments.
    All are relieving regulators, so they exhaust when the downstream pressure exceeds the set pressure. Install them in your air line after your filters.
    Pipe
    Size
    Overall
    Pressure Regulation
    Range, psi
    Input Analog
    Signal
    Inlet
    Outlet
    Max. Flow Rate
    @ Pressure
    Max. Pressure,
    psi
    Gauge
    Included
    No. of Gauge
    Ports
    Wd.
    Ht.
    Housing
    Material
    Max. Temp.,
    ° F
    Electrical
    Connection Type
    Includes
    Enclosure
    Rating
    Each
    NPT Female Inlet × NPT Female Outlet
     
    ±0.5% Regulating Accuracy
    3 to 1204 mA to 20 mA1/4
    		1/4
    		12 scfm @ 100 psi150No12 7/8"4 1/4"Aluminum140HardwireMounting BracketNEMA 4X, IP65
    		4993K30000000
    3 to 1200V DC to 10V DC1/4
    		1/4
    		12 scfm @ 100 psi150No12 7/8"4 1/4"Aluminum140HardwireMounting BracketNEMA 4X, IP65
    		4993K4000000
     
    BSPP Female Inlet × BSPP Female Outlet
     
    ±0.5% Regulating Accuracy
    3 to 1200V DC to 10V DC1/4
    		1/4
    		12 scfm @ 100 psi150No12 7/8"4 1/4"Aluminum140HardwireMounting BracketNEMA 4X, IP65
    		4993K326000000
     

    Compressed Air Filter/Precision Regulators for Particle Removal

    Image of Product. Style A. Front orientation. Compressed Air Filter/Regulators. Compressed Air Filter/Precision Regulators for Particle Removal, Opaque Bowl, Style A.
    Image of Product. Style B. Front orientation. Compressed Air Filter/Regulators. Compressed Air Filter/Precision Regulators for Particle Removal, Opaque Bowl, Style B.

    Style A

    Style B

    With ±0.8% accuracy, these filter/regulators react to smaller pressure changes than our other compressed air filter/regulators. They provide clean air for use in applications where constant, consistent pressure is important. Joined top-to-bottom, the filter and regulator fit in the same space as a filter alone. These regulators are relieving style, so they exhaust when the downstream pressure exceeds the set pressure.
    Automatic Drain—Filters with an automatic drain periodically release condensate into the air, eliminating the need for manual emptying.
    Mounting Brackets—Mounting brackets (sold separately) allow you to attach these filters/regulators to a wall or equipment.
    Filter/Regulators
    Elements
    Mounting
    Brackets
    Pipe
    Size
    Overall
    Style
    Inlet
    Outlet
    Max. Flow Rate
    @ Pressure
    Max. Pressure,
    psi
    Pressure Regulation
    Range, psi
    Removes Particle
    Size Down To, μm
    Wd.
    Ht.
    Regulating
    Accuracy
    Each
    Each
    Each
    NPT Female Inlet × NPT Female Outlet
     
    Aluminum Housing—Opaque Bowl with Automatic Drain
    A1/4
    		1/4
    		30 scfm @ 100 psi1500 to 12053 1/8"7 1/8"±0.8%4967K16400000004967K20000004967K3300000
    A1/2
    		1/2
    		180 scfm @ 100 psi1500 to 12053 1/8"9 3/4"±0.8%4967K9310000004967K6000004967K330000
     
    Aluminum Housing—Opaque Bowl with Manual Drain
    A1/4
    		1/4
    		25 ft³/min @ 100 psi2500 to 12053 1/8"7 1/4"±0.8%4967K123000004967K2000004967K330000
    A1/2
    		1/2
    		80 ft³/min @ 100 psi2500 to 12053 1/8"9 3/4"±0.8%4967K1330000004967K6000004967K330000
    B1/4
    		1/4
    		22 ft³/min @ 100 psi2500 to 12053 1/8"7 3/4"±0.8%4967K24000004967K2000004967K330000
     
    back to top