McMaster-Carr logo
    Filter by
    Reamer Fractional Size
    System of Measurement
    Reamer Diameter
    Flute Type
    Flute Length
    Reamer Operation
    Overall Length
    Number of Flutes
    Spiral Direction
    Machine Taper Number
    Hex Shank Size
    Performance
    Sold As
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Comments
    E-mail address (if you would like a response)
    5 Products

    Reamers
    3D CAD models available

    Finish holes to precise inch, metric, wire gauge, or letter sizes with these reamers.
    Round Shank
    These reamers fit in the chuck of drill presses, turret lathes, and other machine and power tools, making them the most common shank type.
    Straight Flute—The most common flute style, these reamers are suitable for a wide range of applications, but not recommended for holes with a keyway or other breaks in the surface.
    Spiral Flute—Since these reamers clear chips better than straight flutes, they leave holes with a smoother finish. They're better for holes with breaks in the surface, such as a keyway, because they cut continuously across the breaks instead of moving in and out.
    High-Speed Steel—Durable and wear resistant, these are good for general purpose reaming in most materials.
    Cobalt Steel—With better heat and wear resistance than high-speed steel, these reamers run up to 25% faster, last longer, and perform better on hard materials, such as cast iron, hardened steel, titanium, and stainless steel.
    Right-Hand Spiral—These reamers pull chips upward as they cut, so they're often used in blind holes.
    Lg.
    Reamer Dia.
    Material
    Flute
    Overall
    No. of
    Flutes
    Spiral
    Direction
    Cutting Dia.
    Tolerance
    For Use On
    Each
    Straight Flute
    Image of Product. Front orientation. Contains Annotated. Reamers. Reamers, Round Shank, Straight Flute.
     
    Inch
    0.7188" (23/32")High-Speed Steel2 1/4"9"8__0" to 0.0003"Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel00000000000000
    0.7188" (23/32")Cobalt Steel2 1/4"9"8__0" to 0.0004"Aluminum, Brass, Bronze, Iron, Nickel, Plastic, Stainless Steel, Steel, Titanium, Tool Steel, Hardened Steel0000000000000
     
    Spiral Flute
    Image of Product. Front orientation. Contains Annotated. Reamers. Reamers, Round Shank, Spiral Flute.
     
    Inch
    0.7188" (23/32")High-Speed Steel2 1/4"9"8Right Hand0.0001" to 0.0004"Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel000000000000
     

    Reamers for Hole Alignment

    Enlarge holes to correct misalignment and overlap. Misaligned holes often have a narrow entry, so the tapered shape is easier to insert and makes more contact to remove the overlapping material. These are also known as bridge and car reamers.
    Hex Shank
    Image of Product. Front orientation. Contains Annotated. Reamers. Reamers for Hole Alignment, Hex Shank, Spiral Flute.

    Spiral Flute

    The shank fits hex impact sockets, so you can use an impact wrench to both ream the hole and install a fastener.
    Spiral Flute—Since these reamers clear chips better than straight flutes, they leave holes with a smoother finish. They're better for holes with breaks in the surface, such as a keyway, because they cut continuously across the breaks instead of moving in and out.
    High-Speed Steel—Durable and wear resistant, these are good for general purpose reaming in most materials.
    Left-Hand Spiral—These reamers push chips downward as they cut, so they're often used in through holes.
    Strong Hold—Magnets on the shank’s end keep these reamers from accidentally falling out of your tool.
    Lg.
    Reamer Dia. (A)
    Reamer Dia.
    (B)
    Material
    Hex Shank
    Size
    Flute
    Overall
    Spiral
    Direction
    Cutting Dia.
    Tolerance
    Performance
    For Use On
    Each
    Spiral Flute
     
    Inch
    1.2500" (1 1/4")0.7188"High-Speed Steel1 13/16"5"7"Left Hand0" to 0.01"Strong HoldAluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel00000000000000
     
    Morse Taper Shank
    Image of Product. Front orientation. Contains Annotated. Reamers. Reamers for Hole Alignment, Morse Taper Shank, Spiral Flute.

    Spiral Flute

    These reamers work with machine tools that have a Morse taper-spindle hole, such as a drill press or lathe.
    Spiral Flute—Since these reamers clear chips better than straight flutes, they leave holes with a smoother finish. They're better for holes with breaks in the surface, such as a keyway, because they cut continuously across the breaks instead of moving in and out.
    High-Speed Steel—Durable and wear resistant, these are good for general purpose reaming in most materials.
    Left-Hand Spiral—These reamers push chips downward as they cut, so they're often used in through holes.
    Lg.
    Reamer Dia. (A)
    Reamer Dia.
    (B)
    Material
    Machine
    Taper No.
    Flute
    Overall
    Spiral
    Direction
    Cutting Dia.
    Tolerance
    For Use On
    Each
    Spiral Flute
     
    Inch
    1.2500" (1 1/4")0.7188"High-Speed SteelMorse 35"9 1/2"Left Hand0" to 0.01"Aluminum, Brass, Bronze, Iron, Plastic, Stainless Steel, Steel00000000000000
     
    back to top