We will reply to your message within an hour.
Install directly into a mounting surface to suspend threaded rod from ceilings and walls.
Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.
Add an eye nut to threaded rod to hang the rod from rings, hooks, and hangers.
Mount these beams across parallel roof joists to hang threaded rod and route pipe, duct, and other overhead systems in areas where there’s no anchoring point.
These 18-8 stainless steel anchors have good chemical resistance.
More corrosion resistant than 18-8 stainless steel anchors, these 316 stainless steel anchors have excellent resistance to chemicals and salt water.
A zinc plating provides corrosion resistance in wet environments.
Install like a stud anchor—just thread the anchor, a nut, and a washer onto the end of a threaded rod, drive into a hole, and turn the nut to expand the base. Also known as rod anchors, they're often used with threaded rod to hang pipe and wiring.
These 316 stainless steel anchors have excellent resistance to chemicals and salt water.
Often referred to as four-way expansion anchors, these expand in four directions to resist loosening from vibration.
Also known as double expansion anchors, these expand from both sides for full contact and a secure hold.
Also known as caulk-in anchors, these stay secure when there's not much material to hold.
These steel anchors are available with corrosion-resistant finishes.
Keep fixtures solidly in place—these anchors have two locking wedges that won't shake loose.
The removable flat head provides a flush finish in countersunk holes.
An open-end cap nut provides a finished appearance.
Turn the bolt to expand the nut for a secure hold in concrete. These anchors are often used to anchor machinery.
Bolts are beveled under the head for a flush finish in countersunk holes.
A hex head allows for a secure grip with a wrench.
Also known as drive rivets, install by hammering the screw into the body. Unthread the screw to remove.
These anchors are also known as drive rivets. To install, hammer the screw into the body. Unthread the screw to remove.
Also known as drive rivets, install these anchors by hammering the pin into the body. Pry out the pin to remove.
These anchors are also known as drive rivets. To install, hammer the pin into the body. Pry out the pin to remove.
A tamper-resistant nut prevents unwanted removal of the object you are anchoring.
Use in applications requiring high strength.
Also known as tap-in or uni-tap rivets, these anchors are barbed to resist pull out. Made from nylon, they're chemical resistant.
Use with any type of sheet metal or wood screw.
Also known as mungo anchors, these have large fins that prevent rotation.
Also known as lag shields, these anchors are designed for use with large-diameter wood screws.
These stud anchors strengthen the parts of buildings where steel framing connects to concrete. They’re also known as Nelson studs.
18-8 stainless steel anchors have good chemical resistance.
For narrow holes and small cavities where toggle anchors won't fit.
A pivoting toggle bar creates a strong hold.
These stud-style anchors include a nut and a washer.
Used with adhesive in bricks and hollow blocks, such as cinder blocks, these mesh tubes create a stronger hold for rods and studs than other anchors.
Use these stud-style anchors with nuts.
Easy to install, tap these anchors in like a nail—no drilled hole required.
A drilled hole is required for installation.
Fins prevent these anchors from spinning during installation.
A spring-loaded toggle holds against the back of the material.
Bolts are beveled under the head for use in countersunk holes.
A shallow head makes these bolts good for low-clearance applications.
These anchors fit a range of sheet metal and wood screw sizes since they form their own threads when installed.
High-strength toggle anchors provide an extremely strong hold and stay in position when a bolt is removed.
Drill holes with the point on these hangers.
You can use these versatile hangers in a threaded hole (as you would a screw), or secure them with a nut (as you would a bolt).
These hangers have internal threads for use with threaded rods, bolts, and anchors.
Wedge these hangers in concrete and other solid materials.
Drive these hangers into wood with an adjustable wrench, pliers, or a special driver bit.
The spring holds the washer and toggle against opposite sides of the wall, so everything's in position before you begin tightening. Once tightened, the spring adds vibration resistance.
These hangers are a popular choice for overhead applications.
Also known as Tapcons, use these screws in applications requiring high strength.
These blue and silver ultra-corrosion-resistant coated steel screws stand up to wet environments.
These 410 stainless steel screws are more corrosion resistant than ultra-corrosion-resistant coated steel screws.
About half the strength of medium-strength bolts, these bolts are for light duty work-holding.
Made from steel comparable to Grade 5 steel, these bolts are suitable for most work-holding applications.
Turn these studs with a hex key for ease of installation.
18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.
These metric 316 stainless steel studs have excellent resistance to chemicals and salt water. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.
These studs are also known as hanger bolts—use them to hang, mount, and fasten parts to wood structures.
Also known as dowel screws, use these to join two pieces of wood.
A hollow center allows these studs to be used as an axle, a vent, or a passageway for wiring.
The shoulder’s diameter is slightly smaller than listed, so these studs fit most machinery and equipment.
A wing-like toggle holds against the back of the material and spreads the force over a large area to hold 30 lbs. or more.
Use these light duty anchors to hold 20 lbs. or less.
Also known as Tapcons, these screws are often used to anchor parts to concrete, block, and brick. Assortments include a drill bit.
A black-oxide finish provides mild corrosion resistance.
These stainless steel anchor studs offer excellent corrosion resistance.
Rails are drilled with consistently spaced holes for multiple mounting options that do not require machining. Use this steel bolt-together framing to build guards, tables, and racks.