About Track Rollers
Also known as cam followers, track rollers have a thick outer roller that runs directly on a flat surface.
More
About Durometer
Durometer is the international standard for measuring the hardness of rubber, plastic, and most nonmetallic materials.
More
Tight-Tolerance Drive Rollers
The surface of these rollers is molded to a tolerance of either ±0.003 in. or ±0.08 mm to provide more consistent surface contact. Also known as contact wheels and feed rollers, they have tapped hubs that allow you to mount them onto a shaft or stud to transmit power. The urethane surface is nonmarring and wear resistant.
For technical drawings and 3-D models, click on a part number.
Roller | Set Screws | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | For Shaft Dia. | Hub Wd. | Shaft Mount Type | No. Required | Included | Temperature Range, ° F | Choose a Durometer (Hardness Rating) | Each | |
Urethane Roller with Aluminum Hub | ||||||||||
| 25mm | 12mm | 6mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 000000 | |
| 25mm | 12mm | 8mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 30mm | 12mm | 6mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 30mm | 12mm | 8mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 35mm | 12mm | 8mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 35mm | 12mm | 10mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 40mm | 12mm | 10mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 40mm | 12mm | 12mm | 8mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 50mm | 12mm | 12mm | 10mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
| 60mm | 12mm | 10mm | 12mm | Set Screw | 2 | Yes | -40° to 180° | 00000000 | 00000 | |
Threaded Track Rollers
Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting.
Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.
Rollers with seal have end seals to protect rolling elements from dirt and contamination.
Track lubricators reduce friction and wear without shutting down equipment. Oil-infused resin distributes lubricant onto rollers, which transfer it to your track.
For technical drawings and 3-D models, click on a part number.
Track Rollers | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Roller, mm | Stud, mm | Thread | Shoulder, mm | Radial Load Cap., lbs. | Roller-Mount Track Lubricators | |||||||||||||
| Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Includes | Each | Each | ||
Black-Oxide Steel Flat Rollers without Seal | ||||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1 | 12 | 15 | 0.6 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | __ | 00000000 | 0000000 | 0000000 | 000000 |
| 26 | 12 | 10 | 23 | M10 | 1 | 12 | 15 | 0.6 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | __ | 00000000 | 000000 | 0000000 | 00000 |
Black-Oxide Steel Flat Rollers with Seal | ||||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1 | 12 | 15 | 0.6 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | __ | 00000000 | 000000 | 0000000 | 00000 |
| 26 | 12 | 10 | 23 | M10 | 1 | 12 | 15 | 0.6 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | __ | 00000000 | 000000 | 0000000 | 00000 |
Black-Oxide Steel Crowned Rollers without Seal | ||||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1.25 | 13 | 15 | 0.6 | 13,500 | 1,300 | 1,100 | 250° | Needle Roller | __ | 00000000 | 000000 | 0000000 | 00000 |
| 26 | 12 | 10 | 23 | M10 | 1 | 12 | 15 | 0.6 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | __ | 00000000 | 000000 | 0000000 | 00000 |
Black-Oxide Steel Crowned Rollers with Seal | ||||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1 | 12 | 15 | 0.6 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | __ | 00000000 | 000000 | 0000000 | 00000 |
| 26 | 12 | 10 | 23 | M10 | 1 | 12 | 15 | 0.6 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | __ | 00000000 | 000000 | 0000000 | 00000 |
Steel Flat Rollers without Seal | ||||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1.25 | 12 | 17 | 0.6 | 8,000 | 1,500 | 1,200 | 245° | Needle Roller | Mounting Hardware | 0000000 | 00000 | 0000000 | 00000 |
| 26 | 12 | 10 | 23 | M10 | 1.25 | 12 | 17 | 0.6 | 8,000 | 1,500 | 1,200 | 245° | Needle Roller | Mounting Hardware | 0000000 | 00000 | 0000000 | 00000 |
Steel Flat Rollers with Seal | ||||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1.25 | 12 | 17 | 0.6 | 8,000 | 1,500 | 1,200 | 175° | Needle Roller | Mounting Hardware | 0000000 | 00000 | 0000000 | 00000 |
| 26 | 12 | 10 | 23 | M10 | 1.25 | 12 | 17 | 0.6 | 8,000 | 1,500 | 1,200 | 175° | Needle Roller | Mounting Hardware | 0000000 | 00000 | 0000000 | 00000 |
Maintenance-Free Threaded Track Rollers
Because they never need to be relubricated, these rollers are a good choice for hard-to-reach places. Also known as cam followers, track rollers support loads while guiding and positioning work. Thread the stud directly into a component or secure with a nut for through-hole mounting. Some rollers have end seals to block dirt and contamination.
Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.
Track lubricators reduce friction and wear without shutting down equipment. Oil-infused resin distributes lubricant onto rollers, which transfer it to your track.
For technical drawings and 3-D models, click on a part number.
Track Rollers | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Roller, mm | Stud, mm | Thread | Radial Load Cap., lbs. | Roller-Mount Track Lubricators | |||||||||||||
| Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Shoulder Lg., mm | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Includes | Each | Each | ||
Steel Crowned Rollers with Seal | |||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1.25 | 12 | 0.6 | 1,000 | 1,500 | 1,200 | 175° | Needle Roller | Mounting Hardware | 000000 | 0000000 | 0000000 | 000000 |
| 26 | 12 | 10 | 23 | M10 | 1.25 | 12 | 0.6 | 1,000 | 1,500 | 1,200 | 175° | Needle Roller | Mounting Hardware | 000000 | 000000 | 0000000 | 00000 |
Threaded Track Rollers with Adjustable Shoulder
Also known as eccentric track rollers, the shoulder adjusts up or down to align to your track, enabling uniform alignment among rollers in a system. Secure the stud with a nut for through-hole mounting. All rollers have end seals to protect rolling elements from dirt and contamination.
Crowned rollers have a slight curve, which is invisible to the naked eye, to stay centered on surfaces that are not perfectly aligned and/or not perfectly flat.
For technical drawings and 3-D models, click on a part number.
Roller, mm | Stud, mm | Thread | Shoulder, mm | Radial Load Cap., lbs. | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Dia. | Wd. | Dia. | Lg. | Size | Pitch, mm | Lg., mm | Dia. | Lg. | Ht. Adjustment Capability, mm | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Includes | Each | |
Steel Flat Rollers with Seal | |||||||||||||||||
| 22 | 12 | 10 | 23 | M10 | 1 | 12 | 13 | 10 | 0.5 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | Mounting Hardware | 0000000 | 0000000 |
| 26 | 12 | 10 | 23 | M10 | 1 | 12 | 13 | 10 | 0.5 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | Mounting Hardware | 0000000 | 000000 |
Steel Crowned Rollers with Seal | |||||||||||||||||
| 26 | 12 | 10 | 23 | M10 | 1.25 | 13 | 13 | 10 | 0.5 | 9,000 | 2,300 | 1,700 | 250° | Needle Roller | Mounting Hardware | 0000000 | 000000 |
Tapered Stud Track Rollers
Install these rollers in worn-out mounting holes or where you don’t have access to the back of the mounting hole. The stud is tapered, so you can quickly secure them in place with a set screw (not included) instead of a nut on the back like traditional rollers. Keep in mind, this reduces their radial capacity.
Rollers with a seal protect rolling elements from dirt and contamination better than shielded rollers, but they do hold more heat. The seal also helps retain lubrication.
Add a grease fitting to create a lubrication point.
For technical drawings and 3-D models, click on a part number.
Track Rollers | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Roller, mm | Stud, mm | Shoulder, mm | Radial Load Cap., lbs. | Grease Fittings | ||||||||||
| Dia. | Wd. | Dia. | Lg. | Dia. | Lg. | Max. Speed, rpm | Static | Dynamic | Max. Temp., °F | Bearing Type | Each | Each | ||
Steel Flat Rollers with Seal | ||||||||||||||
| 22 | 12 | 10 | 20 | 17 | 0.6 | 11,900 | 1,500 | 1,100 | 175° | Needle Roller | 0000000 | 000000 | 0000000 | 00000 |
| 26 | 12 | 10 | 20 | 20 | 0.6 | 11,900 | 1,500 | 1,100 | 175° | Needle Roller | 0000000 | 00000 | 0000000 | 0000 |