Dual pistons make this saw more powerful than the light duty air-powered reciprocating saw and reduce vibration.

The body of this saw is four inches shorter than standard Milwaukee cordless reciprocating saws for easier access to confined spaces.

About 25% lighter than the standard DeWalt electric circular saw, this lightweight saw reduces fatigue during prolonged cutting.

About 25% lighter than the standard Skil electric circular saw, this lightweight saw reduces fatigue during prolonged cutting.

Operate these Milwaukee saws at a low rpm to make smooth, burr-free cuts in metal without excessive heat or the need for coolant.

Operate this saw at a low rpm to make smooth, burr-free cuts in metal without excessive heat or the need for coolant.

Replace the brush on your circular saw.

Replace individual parts in a variety of Milwaukee portable band saws.

Small and light enough to operate with one hand, this saw is a good choice for overhead cuts.

This economy cutoff saw has a lightweight nylon handle and is for less prolonged use than the standard air-powered portable cutoff saw.

The right-angle position of this saw's blade makes it suitable for both cutting and grinding with an abrasive wheel.

An extra-large rubber grip damps vibration and provides comfort during prolonged use.

Cutting in tight spaces is easier with a body that's four inches shorter than the standard Bosch electric jigsaw.

An ergonomic body with a soft grip increases control and comfort with this saw.

Cut, scrape, and grind in tight spaces without having access to an outlet. This tool has an oscillating blade that makes flush and plunge cuts without damaging the surrounding material.

A higher air consumption rating allows this saw to work in longer bursts and power through tougher materials than the light duty air-powered hacksaw.

These saws adjust to cut both horizontally and vertically and have twice the cutting capacity of bench-top band saws for metal.

Make both horizontal and vertical cuts with this saw.

The grinding action of the diamond-grit blade creates a smooth finish on hard materials such as glass, stone, tile, brick, and fiberglass.

This saw is less than half the weight with a smaller wheel diameter than standard bench-top cutoff saws.

Make fast cuts through tough metal, such as angle iron and flat bar, with more than twice the horsepower of bench-top cutoff saws. These saws must be hardwired.

Use this saw to cut precise angles by hand. Also known as a miter box saw.

Support sheets of wood and plastic on the large, flat table to make straight cuts with the built-in blade.

Weighing only 12 pounds, this bench-top saw is a portable choice for light duty cutting, such as frame making and model building.

Pins hold hose slightly bent, pulling it apart as the knife-edge blade slices a straight, smooth cut.

A circular saw mounted to a track allows you to make straight vertical and horizontal cuts in large sheets of wood and plastic that won't fit on a table saw.

Hacksaw blades of any length fit this saw to make cuts in holes and tight spaces.

The blade extends past the frame to make flush cuts.

Nonslip, cushioned grips on the handle and front end let you get a tight grip with two hands while cutting tough materials.

This large-throat-depth saw makes deeper cuts than standard hacksaws for tight curves. It's also known as a fret saw.

Made of materials that are FM approved, these hacksaws have an aluminum-bronze frame and a beryllium copper blade. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Teeth sharpened on three sides make fast, accurate cuts in wood and plastic.

The thin blade flexes to make flush cuts.

The pointed tip makes plunge cuts in drywall.

Carbide-tipped teeth last longer than the steel teeth on standard handsaws for drywall.

A blade made of carbon steel cuts plastic pipe, plasterboard, and plywood.

Cut wood, plywood, and particleboard.

These blades have a heat-resistant coating to prevent material buildup.

Square-shaped teeth cut across the grain and with the grain (ripping) in reclaimed lumber and flooring with embedded nails.

A razor-sharp knife edge minimizes dust and makes quick, clean cuts through foam sheets such as expanded polystyrene insulation and extruded polystyrene.

The carbide-grit edge on these blades cuts brittle and abrasive materials including glass and fiberglass.

Use these blades with water or coolant to produce smoother cuts in tile than dry-cutting blades. They're also for use on glass.

The edge of the blade is segmented to cut faster than a continuous edge.

The edge of the blade is segmented to cut faster than a continuous edge.

Make fast, clean cuts in steel sheets, angle iron, rebar, and pipe with the carbide teeth on these blades.

Cut stainless steel sheets, pipe, tubing, and grating with teeth made of impact-resistant carbide.

Cut wood, plywood, and particleboard.

These blades have a heat-resistant coating to prevent material buildup.

Also known as dado-head blades, these are for cutting grooves in all types of wood.

A razor-sharp knife edge minimizes dust and makes quick, clean cuts through foam sheets such as expanded polystyrene insulation and extruded polystyrene.

Make clean cuts in rubber and plastic hose with the scalloped knife edge on these blades.

A continuous edge on these blades produces smooth cuts.

The edge of the blade is segmented to cut faster than a continuous edge.

The carbide-grit edge on these blades cuts brittle and abrasive materials including glass and fiberglass.

Teeth are carbide tipped and designed to push chips away from the blade to prevent clogging and produce smooth cuts in aluminum sheets, tubing, and T-slotted framing.

Cut stainless steel sheets, pipe, tubing, and grating with teeth made of impact-resistant carbide.

Cut plastic, wood, and soft metal such as aluminum, brass, and copper.

The segmented edge on these blades is coated with diamond grit for cutting plastic.

Blades and teeth are steel and treated to a Rockwell Hardness between C63 and C65 for increased wear resistance when cutting through steel and cast iron bars, rods, pipe, and tubing.

These blades have a higher concentration of diamonds than other dry-cutting blades, so they last up to three times longer.

Teeth vary in size, number per inch, and pattern to reduce vibration, so they create a smoother finish than Long-Life Band Saw Blades. They're also known as variable-set blades.

Make clog-free cuts in thick cross sections of steel, aluminum, brass, bronze, wood, and plastic. These blades have forward-angled teeth and plenty of space for chips to collect.

Teeth vary in size, number per inch, and pattern to reduce vibration, so they create a smoother finish than Long-Life Band Saw Blades for Thin Metal. They're also known as variable-set blades.

These carbon steel blades are good for making straight cuts.

Cut curves with these flexible carbon steel blades.

The tightly spaced, V-shaped teeth on these blades cut through soft materials more quickly than scallop-edge blades.

Titanium aluminum nitride (TiAlN) coated, precision-ground teeth cut quickly and leave a smooth edge on stainless steel, nickel, and titanium.

The teeth on these steel blades are carbide tipped, so they'll last longer and produce a smoother cut than other band saw blades when cutting fiberglass, plastic, and composites.

These rigid carbon steel blades make straight cuts.

Use these carbon steel blades to make straight cuts.