These structural sealants combine the mechanical strength of an adhesive with excellent sealing properties and high flexibility. They’re non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. For joints between dissimilar materials and in environments with wide temperature fluctuation, choose a sealant with a higher elongation or joint compression/expansion tolerance. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Often used in high-vibration applications that could cause standard thread sealants to fail, these never fully harden and remain pliable enough to self-heal and stop leaks before they start. Formulated without PTFE, these sealants are less slippery and less likely to result in overtightenting than sealants that have PTFE, making them good for plastic pipe where overtightening could lead to cracks and breaks. They have low locking strength, so they can be adjusted without tools.

Clear enough to read through, this UV-resistant sealant allows optimal light transmission for use with solar cells and fiber optics. Apply it in cold temperatures, on wet surfaces, and even through running water. The sealant is non-sagging, so it won't drip from vertical and overhead surfaces. It cannot be sold to the regions listed due to local regulatory limits on VOC (volatile organic compounds).

Elongation indicates flexibility—the higher the value is, the more a sealant can stretch. This sealant is good for use between dissimilar materials and in environments with wide temperature fluctuation.

Form seals that resist punctures, cuts, and abrasion to withstand heavy wear and tampering. These sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation.

While other threadlockers can cause brittleness and cracking, these liquids won’t weaken plastic. They secure nylon, PTFE, and other plastic fasteners.

Tough enough to be permanently submersed in seawater, these compounds protect sensitive electronics, such as circuit boards, semiconductors, and sensors in harsh environments. They resist moisture, salt, and chemicals, so you can use them in corrosive oil, marine, and mining applications. These compounds can also be used within autoclaves. Because they are epoxies, they are rigid, resist wear, and create excellent electrical insulation. They withstand a wide range of temperatures, and this formulation won’t crack or split as components heat up and cool down.

They come in a cartridge, so you can apply them precisely. To dispense, they require a mixer nozzle and gun (both sold separately).

Also known as neutral-cure sealants, these won't discolor copper, brass, and concrete. They’re non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone rubber, sealants are RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. Sealants that are good for joining dissimilar materials also work well in environments with wide temperature fluctuation.

Clear enough to read through, these UV-resistant sealants allow optimal light transmission for use with solar cells and fiber optics. Sealants are non-sagging, so they won't drip from vertical and overhead surfaces.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain.

Bonds to itself for a permanent, watertight seal. This tape has no adhesive, so it won't dry out and crack, which can cause standard tape to fail over time. The rubber backing molds to irregular surfaces and withstands demanding conditions, making this tape a good choice for patching and sealing anything from roofs to pipes.

Unlike most threadlockers, these don't need to be applied every time you remove and reinstall your fasteners. Put on a fresh layer once every three to five uses.

Seal concrete joints in high-traffic locations—these sealants stand up to heavy wear and tear, such as steel wheel traffic. Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.

Tested to meet ASTM E595, a standard used by NASA, these sealants fill joints and seams while releasing almost no volatile emissions that could damage sensitive electronics, even in a vacuum. Made of silicone rubber, they’re RTV (room-temperature vulcanizing), so they’ll fully harden at room temperature.

Elongation indicates flexibility—the higher the value is, the more a sealant can stretch.

Seal concrete joints in high-traffic areas—these sealants stand up to heavy wear and tear, such as steel wheel traffic. They're non-sagging, so they won't drip from vertical and overhead surfaces. Made from silicone rubber, sealants are RTV (room-temperature vulcanizing).

Elongation and joint compression/expansion tolerance indicate flexibility—the higher the values are, the more joint movement sealants can sustain. These sealants are best suited to joints between similar materials that aren't exposed to wide temperature fluctuation. For high-wear applications, choose a harder sealant for the most abrasion resistance.