1 3/4" Shaft Diameter Shaft Seals

Filter by

System of Measurement

Seal ID

Seal OD

Seal Width

Bore Diameter

For Use With

Diluted Salt Solutions

Loaded Type

Maximum Temperature

For Shaft Motion

For Sealing

Maximum Rotation Speed

Material

Maximum Pressure

Color

For Minimum Bore Width

Rotation Speed

2,000 rpm to 2,999 rpm

3,000 rpm to 9,999 rpm

10,000 rpm to 19,999 rpm

Case Material

Aramid

Stainless Steel

Steel

U.S.–Mexico–Canada Agreement (USMCA) Qualifying

Hardness

DFARS Specialty Metals

Exempt

Export Control Classification Number (ECCN)

REACH

RoHS

Minimum Temperature

Hardness Rating

18 Products

Spring-Loaded Rotary Shaft Seals with Wiper Lip


Side 1	Side 2	Profile

Used to retain oil on rotating shafts in motors, pumps, bearings, and gearboxes, these seals have a secondary lip that blocks contaminants. Also known as oil seals, a spring secures the lip against the shaft, preventing messy leaks. Press-fit seals into the bore around the shaft. Seals with a maximum pressure of 50 psi should be secured with a retaining ring.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

Acrylic-Coated Case—Seals with an acrylic-coated case have a coating that compensates for surface imperfections in the housing bore for a tight seal on the OD.

		Seal			For Bore							Case
	For Shaft Dia.	ID	OD	Wd.	Dia.	Min.Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color	Finish	Color	Specs. Met		Each
Buna-N with Steel Case and Steel Spring



		1 3/4"	1.750"	2.500"	0.313"	2.500"	0.329"	3,100	10	-40 to 210	Durometer 80A (Hard)	Black	Acrylic Coated	Green	DIN 3760, ISO 6194	5154T44	000000


		1 3/4"	1.750"	2.502"	0.500"	2.502"	0.516"	3,100	50	-40 to 210	Durometer 80A (Hard)	Black	Acrylic Coated	Green	DIN 3760, ISO 6194	5154T96	00000

Bore-Sealing Spring-Loaded Rotary Shaft Seals with Wiper Lip


Side 1	Side 2	Profile

Ribbed Buna-N over steel creates a tight seal with the bore, even when mating with a rough surface or in a split housing. Also known as oil seals, these retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. They have a secondary lip that blocks contaminants and a spring that secures the sealing-lip to prevent leaks. Press-fit seals into the bore around the shaft. Seals with a maximum pressure of 145 psi should be secured with a retaining ring.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

		Seal			For Bore
	For Shaft Dia.	ID	OD	Wd.	Dia.	Min.Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color		Each
Buna-N with Steel Core and Steel Spring



		1 3/4"	1.750"	2.500"	0.313"	2.500"	0.325"	3,000	7	-40 to 212	Durometer 70A (Hard)	Black	1199N73	00000

Heavy Duty Shaft-Mounted Rotary Shaft Seals


Side 1	Side 2	Profile

These seals are fluoroelastomer, so they have excellent chemical resistance and withstand temperatures up to 390° F. Also known as V-rings and flingers, they protect shaft bearings by blocking dust and other contaminants while retaining lubricant. To install, stretch the seal over your shaft and press it firmly against the face plate.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

	For Shaft			Seal
	Dia.	Dia. Range	For Faceplate Dia.	ID	OD	Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color		Each
Fluoroelastomer



		1 3/4", 1 7/8"	1.693" to 1.89"	2.283" to 2.480"	1.575"	1.969"	0.354"	3,800	5	5 to 390	Durometer 60A (Medium)	Brown	1670N23	000000

Shaft-Mounted Rotary Shaft Seals


Side 1	Side 2	Profile

Also known as V-rings and flingers, these seals protect shaft bearings by blocking dust and other contaminants while retaining lubricant. They’re Buna-N for excellent resistance to oil and grease. To install, stretch the seal over your shaft and press it firmly against the faceplate. The Seal OD and Seal Width listed are the dimensions of the seal after it is installed.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

	For Shaft			Seal
	Dia.	Dia. Range	For Faceplate Dia.	ID	OD	Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color		Each
Buna-N



		1 3/4"	1.700" to 1.890"	2.300" to 2.490"	1.564"	2.359"	0.375"	3,800	100	-20 to 225	Durometer 85A (Hard)	Black	9562K49	00000

Rotary Shaft Seals for Grease


Side 1	Side 2	Profile

Also known as grease seals, these are designed to retain thick lubricant at low pressure in motors, pumps, bearings, and gearboxes. They have a light grip on the shaft that creates less friction than spring-loaded seals. Press-fit seals into the bore around the shaft.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

Acrylic-Coated Case—Seals with an acrylic-coated case have a coating that compensates for surface imperfections in the housing bore for a tight seal on the OD.

		Seal			For Bore							Case
	For Shaft Dia.	ID	OD	Wd.	Dia.	Min.Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color	Finish	Color	Specs. Met		Each
Buna-N with Steel Case



		1 3/4"	1.750"	2.250"	0.188"	2.250"	0.204"	3,100	10	-40 to 210	Durometer 75A (Hard)	Black	Acrylic Coated	Green	DIN 3760, ISO 6194	5154T88	000000

Spring-Loaded Rotary Shaft Seals


Side 1	Side 2	Profile

Also known as oil seals, use these to retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. A spring secures the lip against the shaft, preventing messy leaks. Press-fit seals into the bore around the shaft. Seals with a maximum pressure of 50 psi should be secured with a retaining ring.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

Acrylic-Coated Case—Seals with an acrylic-coated case have a coating that compensates for surface imperfections in the housing bore for a tight seal on the OD.

		Seal			For Bore							Case
	For Shaft Dia.	ID	OD	Wd.	Dia.	Min.Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color	Finish	Color	Specs. Met		Each
Buna-N with Steel Case and Steel Spring



		1 3/4"	1.750"	2.250"	0.313"	2.250"	0.329"	3,100	10	-40 to 210	Durometer 75A (Hard)	Black	Acrylic Coated	Green	DIN 3760, ISO 6194	5154T29	000000

High-Speed Rotary Shaft Seals


Side 1	Side 2	Profile

A slippery PTFE surface allows these seals to function at speeds at least 25% faster than other rotary shaft seals. Also known as oil seals, use these to retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. An O-ring secures the lips to prevent leaks, while sealing against the housing. Press-fit seals into the bore around the shaft.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

		Seal			For Bore							O-Ring
	For Shaft Dia.	ID	OD	Wd.	Dia.	Min.Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color	Hardness	Color		Each
Graphite Filled PTFE with Buna-N O-Ring



		1 3/4"	1.750"	2.250"	0.313"	2.250"	0.323"	10,900	150	-40 to 250	Durometer 60D (Extra Hard)	Black	Durometer 70A (Hard)	Black	2122N19	000000

Mechanical Pump Shaft Seals with Extended Spring

Seal with Retainer

and Straight Spring

For use in waste water, boiler feed, and compressor pumps, these seals have an extra-long spring that accommodates variations in seal cavity length. They come furnished as two pieces—the seal and the seat. The seal is comprised of the case, spring, diaphragm, and washer, which come locked together as one piece. Seal Width represents the working height, which is the compressed length when installed. The seat is comprised of the seat and the gasket.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

Buna-N Diaphragm—Buna-N diaphragms resist grease and a wide range of oils.

EPDM Diaphragm—EPDM diaphragms are more resistant to water and steam than Buna-N and Viton® fluoroelastomer, but aren’t as resistant to oils and chemicals.

Viton® Fluoroelastomer Diaphragm—Viton® fluoroelastomer diaphragms resist a wider range of chemicals than Buna-N.

Buna-N Gasket—Buna-N gaskets resist grease and a wide range of oils.

Viton® Fluoroelastomer Gasket—Viton® fluoroelastomer gaskets resist a wider range of chemicals than Buna-N.

Carbon Washer—Carbon washers are for use with clean liquids.

Silicon Carbide Washer—Silicon carbide washers have a hard surface that resists scratching, so they can be used with liquids that contain abrasives.

Cannot Be Sold Outside North America—Products cannot be sold outside North America due to restrictions.

				Seal			Seat			Material
	For Shaft Dia.	Mfr. Equiv. No.	Mfr./Brand Equiv.	ID	OD	Wd.	ID	OD	Wd.	Washer	Seat	Spring Shape	Includes	Max. Pressure, psi	Cannot Be Sold To		Each
304 Stainless Steel Case and 304 Stainless Steel Spring with Buna-N Diaphragm and Buna-N Gasket



		1 3/4"	237, 446	John Crane Type 21 Pac-Seal Type 21 Pac-Seal Type 31 Sealol Type 43 CE Short Sealol Type 43 CU Short	1.750"	2.446"	1.375"	1.796"	2.500"	0.500"	Carbon	Ceramic	Straight	Spring Retainer	250	Outside North America	9281K285	000000


		304 Stainless Steel Case and 304 Stainless Steel Spring with Viton® Fluoroelastomer Diaphragm and Viton® Fluoroelastomer Gasket



				1 3/4"	237V	John Crane Type 21 Pac-Seal Type 21 Pac-Seal Type 31 Sealol Type 43 CE Short Sealol Type 43 CU Short	1.750"	2.446"	1.375"	1.796"	2.500"	0.500"	Carbon	Ceramic	Straight	Spring Retainer	250	Outside North America	9281K8	00000


				1 3/4"	237VSC	John Crane Type 21 Pac-Seal Type 21 Pac-Seal Type 31 Sealol Type 43 CE Short Sealol Type 43 CU Short	1.750"	2.446"	1.375"	1.796"	2.500"	0.500"	Silicon Carbide	Silicon Carbide	Straight	Spring Retainer	250	Outside North America	9281K249	000000


				304 Stainless Steel Case and 304 Stainless Steel Spring with EPDM Diaphragm and EPDM Gasket



						1 3/4"	237E	John Crane Type 21 Pac-Seal Type 21 Pac-Seal Type 31 Sealol Type 43 CE Short Sealol Type 43 CU Short	1.750"	2.446"	1.312"	1.796"	2.500"	0.500"	Carbon	Ceramic	Straight	Spring Retainer	250	Outside North America	9281K298	00000

Spring-Loaded Rotary Shaft Seals for Misaligned Shafts


Side 1	Side 2	Profile

Designed with an extended lip, these seals have the flexibility to accommodate shaft misalignment up to 0.125". Also known as clipper seals, they retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. A spring secures the lip to prevent leaks. Press-fit seals into the housing bore around the shaft; they fit tight for installation without a cover plate.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

		Seal			For Bore
	For Shaft Dia.	ID	OD	Wd.	Dia.	Min.Wd.	Max. Rotation Speed, rpm	Max. Pressure, psi	Temp. Range, ° F	Hardness	Color	Case Color		Each
Buna-N with Aramid Case and Stainless Steel Spring



		1 3/4"	1.748"	2.624"	0.438"	2.625"	0.438"	2,200	7	-20 to 250	Durometer 75A (Hard)	Black	Black	1885N13	000000

Split Rotary Shaft Seals


Side 1	Side 2	Profile

Replace old seals without disassembling components—these seals come split for easy installation. Also known as clipper seals, they retain oil on rotating shafts in motors, pumps, bearings, and gearboxes. A spring secures the lip to prevent leaks; fasten the hook and eye closure to secure. Press-fit seals into the housing bore; they fit tight for installation without a cover plate.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

		Seal			For Bore
	For Shaft Dia.	ID	OD	Wd.	Dia.	Min.Wd.	Max. Rotation Speed, rpm	Max. Pressure	Temp. Range, ° F	Hardness	Color	Case Color		Each
Buna-N with Aramid Case and Stainless Steel Spring



		1 3/4"	1.750"	2.625"	0.438"	2.625"	0.438"	4,400	Not Rated	-20 to 250	Durometer 75A (Hard)	Black	Black	1651N19	000000

Cartridge Mechanical Shaft Seals

Install these seals faster and with less technical expertise than other mechanical shaft seals that come in two pieces. They come with their seal and seat already assembled. All have a carbon washer that is self-lubricating. However, this means their washer is too soft to be used with abrasive liquids and liquids with harsh additives.

Fluoroelastomer Diaphragm—Seals with a fluoroelastomer diaphragm can be used with a wider range of chemicals than EPDM diaphragms, including benzene, butyl alcohol, and fuels.

EPDM Diaphragm—Seals with an EPDM diaphragm won’t break down from exposure to water and steam. However, they are for use with fewer chemicals.

		Seal				Fluoroelastomer Diaphragm		EPDM Diaphragm
	For Shaft Dia.	ID	OD	Wd.	Max. Pressure, psi		Each		Each
316 Stainless Steel Case and C276 Nickel Spring with PTFE Gasket



		1 3/4"	1.75"	3.563"	2.815"	220	4887N17	000000000	4887N42	000000000

Narrow-Profile Mechanical Pump Shaft Seals with Extended Spring

With a smaller seal OD than standard seals, these seals have an extended spring that accommodates variations in seal cavity length. They're used in waste water, boiler feed, and compressor pumps. Seals come furnished as two pieces—the seal and the seat. The seal is comprised of the case, spring, diaphragm, and washer, which come locked together as one piece. Seal Width represents the working height, which is the compressed length when installed. The seat is comprised of the seat and the gasket.

Note: Maximum performance values cannot be achieved simultaneously; for example, speed is affected by pressure, temperature, and other operating conditions.

Cannot Be Sold Outside North America—Products cannot be sold outside North America due to restrictions.

				Seal			Seat			Material
	For Shaft Dia.	Mfr. Equiv. No.	Mfr./Brand Equiv.	ID	OD	Wd.	ID	OD	Wd.	Washer	Seat	Max. Pressure, psi	Cannot Be Sold To		Each
316 Stainless Steel Case and 316 Stainless Steel Spring with Buna-N Diaphragm and Buna-N Gasket



		1 3/4"	205	John Crane Type 1 Pac-Seal Type 51 Sealol Type 43 CE Long	1.750"	2.300"	2.000"	1.796"	2.500"	0.500"	Carbon	Ceramic	150	Outside North America	9281K467	0000000


		316 Stainless Steel Case and 316 Stainless Steel Spring with Viton® Fluoroelastomer Diaphragm and Viton® Fluoroelastomer Gasket



				1 3/4"	205V	John Crane Type 1 Pac-Seal Type 51 Sealol Type 43 CE Long	1.750"	2.300"	2.000"	1.796"	2.500"	0.500"	Carbon	Ceramic	150	Outside North America	9281K264	000000