8-32 Shafts | McMaster-Carr

Clear All

	End Type End Type


Straight	Keyed

Made to Order	Tapped

Threaded	D-Profile

With Retaining Ring Grooves	Plain

Step Down

	System of Measurement System of Measurement

Inch

	Diameter Diameter

	Length Length

	Thread Size Thread Size	Show

8-32

	Thread Size Thread Size	Hide

	Material Material

	Mechanical Finish Mechanical Finish

Precision Ground

Polished

Turned

	Thread Length Thread Length

	For Motion Type For Motion Type

	Rotary
	Linear

	Edge Type Edge Type

	Chamfered

	Hardness Rating Hardness Rating

Medium

Hard

Very Hard

	Yield Strength Yield Strength

20,000 to 99,999 psi

	Hardness Hardness

	RoHS (Restriction of Hazardous Substances) RoHS (Restriction of Hazardous Substances)

RoHS Compliant

	DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense Acquisition Regulations Supplement)

DFARS Specialty Metals
COTS-Exempt

DFARS Specialty Metals
Compliant

	Heat Treatment Heat Treatment

Case Hardened

Annealed (Softened)

Hardened

	Step Length Step Length

Made to Order

	Surface Smoothness Surface Smoothness

9 microinch

16 microinch

	Surface Yield Strength Surface Yield Strength

200,000 psi

Not Rated

	Keyway Width Keyway Width

	Keyway Length Keyway Length

Made to Order

	Keyway Depth Keyway Depth

	REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration, Evaluation, Authorization and Restriction of Chemicals)

REACH Compliant

Forward

How can we improve?

761 Products

About Shafts

Keyed Rotary Shafts

Combine with a machine key to transmit torque to gears, sprockets, and other power transmission components.

D-Profile Rotary Shafts

A flat surface area allows set screws to dig into the shaft for securely mounting gears, sprockets, and bearings.

Tapped Rotary Shafts

Connect these internally threaded shafts directly to threaded components, or use a fastener to secure.

Threaded Rotary Shafts

Attach threaded accessories, such as mixer propellers and fan blades, to the end of these shafts.

Step-Down Rotary Shafts

A shoulder near the end of the shaft provides a stop for gears, sprockets, and bearings.

Rotary Shafts with Retaining Ring Grooves

Clip retaining rings into the grooves to separate and position gears, sprockets, and bearings.

Linear Motion Shafts

Tapped Linear Motion Shafts

Internal threads allow you to mount these shafts onto threaded studs and fasteners, no shaft supports needed.

Threaded Linear Motion Shafts

Mount these externally threaded shafts into tapped holes rather than using a shaft support, or attach a hex nut, shaft collar, or other threaded accessory.

Step-Down Linear Motion Shafts

A shoulder near the end of the shaft allows for easy positioning of housings, shaft supports, and collars.

Linear Motion Shafts with Retaining Ring Grooves

Clip retaining rings into the grooves to separate and position collars, supports, and housings.

Pull-Out Dowel Pins

Flat-Vent Pull-Out Dowel Pins

The flat side of these pins relieves trapped air, making them easier to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

Pull-Out Dowel Pins

To remove these pins, thread a screw or tool into the tapped hole, then pull them out.

Spiral-Vent Pull-Out Dowel Pins

A spiral groove cut into these pins relieves trapped air but stays in 360° contact with the hole for a secure fit that's easy to insert in and remove from blind holes. To remove, thread a screw or tool into the tapped hole, then pull the pin out.

Threaded Rods and Studs

High-Strength Steel Threaded Rods

Comparable to Grade 8 steel, these threaded rods have a tensile strength of 150,000 psi, making them about 25% stronger than medium-strength steel rods.

Low-Strength Steel Threaded Rods

About half the strength of medium-strength steel threaded rods, use these for light duty hanging, mounting, and fastening.

Left-Hand Threaded Low-Strength
Steel Threaded Rods

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

18-8 Stainless Steel Threaded Rods

18-8 stainless steel threaded rods have good chemical resistance.

Super-Corrosion-Resistant 316
Stainless Steel Threaded Rods

More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.

Nylon Threaded Rods

Made from nylon 6/6, these threaded rods resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.