We will reply to your message within an hour.
Made with ceramic or coated with titanium nitride (TiN), the blades on these scissors stay sharp longer than uncoated stainless steel and steel blades.
Comfortably cut at any angle with these scissors. The blades rotate so your hand doesn’t have to.
For a long-lasting cutting edge that's three times harder than uncoated stainless steel, the blades on these scissors are titanium bonded over stainless steel.
Make quick, repeat cuts without tiring your hand—a spring-action band opens these scissors automatically.
Make clean cuts through duct tape and other sticky materials.
Minimize hand fatigue with a lightweight handle and spring-action that automatically opens the blades for quick repeat cuts.
Longer handles and shorter blades give you more leverage than other scissors to cut tough materials such as leather, rope, and thick cardboard.
S-shaped handles keep your hand clear of material, so you can cut flush against flat surfaces.
Cut precise lengths in fabric and other materials every time.
Minimize hand fatigue—the handles on these scissors are lightweight and spring-action opens the blades for quick repeat cuts.
With durable fine-point blades, these scissors make precise cuts even after repeated use.
The blades have narrow, sharp tips for precise trims and detailed cuts.
Blades are ceramic to stay sharp longer than metal blades.
For extra leverage to cut through tough materials such as leather, rope, and thick cardboard, these scissors have long handles and short blades.
Prevent snags and injuries with the rounded points on these scissors.
Prevent punctures while cutting with the ball-point tip.
Prevent snags and injury with the rounded points on these small scissors.
These small scissors have narrow, sharp tips for fine cutting and trimming.
Short blades make these scissors easy to maneuver in cramped areas for small, detailed cuts less than an inch long.
Trim flush against a flat surface with the curved blades on these small scissors.
Cut the ribbon at your grand opening or other milestone event.
Stop harmful static charges from building up and damaging sensitive equipment while cutting.
For extra leverage to cut through Kevlar, metal, and plastics, these scissors have long handles and short blades.
Cut through the strong fibers of Kevlar.
After each cut, the jaws spring open to make continuous cutting easy.
Precision-ground blades on these scissors make sharp, clean, and uniform cuts in tough rubber and fabric.
A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.
Keep your hand away from the material being cut.
Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.
The handles are angled 90° from the blade so you can cut material from directly above tight spaces.
This cutter has two blades that cut a 1/8" wide strip—peel it back for smooth edges with little distortion.
Prevent waste from flying up as you work. A double blade makes two cuts to create a 7/64"-wide step that peels back, leaving little distortion and smooth edges.
These cutters make straight cuts and curves.
Also known as bulldog snips, these have long handles and short blades for cutting through thick sheet metal with less effort than standard sheet metal cutters.
Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.
Replace blades as they wear. These cutters are also known as tinners' snips.
Handles are angled to keep your hand away from the material as you cut straight lines and curves.
Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.
Sized and shaped like pliers, these sheet metal cutters are small enough to fit in your tool belt.
Make round, square, and irregular-shaped holes with this punch-style hole cutter.
Cut up to 1" deep V-shaped notches in sheet metal.
A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Use to cut patterns in flat material with minimal material loss and less effort compared to manual cutters.
Punch small pieces out of material to create an almost burr-free cut with no material distortion.
Minimize material loss and edge distortion with these scissor-like cutters that cut metal up to 1/64" thick.+
Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.
Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.
These nibblers punch small pieces out of material to create an almost burr-free cut with no material distortion.
Turn your portable drill into a punch cutter for cutting curved and straight shapes in flat and corrugated sheet metal and plastic.
Make straight, clean cuts in thick sheet metal.
A 12" long blade makes long, straight cuts in thin metals and flexible materials. Not for use on phenolic or other rigid materials.
This large-capacity cutter has a 25" blade for long, straight cuts.
Turn your workpiece while cutting to create curves and complex shapes.
Combine the cutting base and a corner punch to make rounded corners in sheet metal.
Notch, cut, and pierce a variety of materials including metal, plastic, and vinyl.
Make straight cuts in sheets. These cutters are foot operated so your hands are free to position the material.
Good for high-volume cutting and trimming.
Make a flush cut that leaves a smooth, finished edge.
Prevent chipping, binding, and fracturing when cutting brittle, high-pressure laminated plastic.
Leave clean cut edges in a variety of pliable materials.
Cut straight lines and patterns with the rotary blades on this cutter.
These air-powered cutters include a semi-square blade for no-fray cuts.
Slice through rubber belts, mats, and sheets.
Make accurate cuts at precise angles. These cutters have a miter guide that is notched to line up your workpiece.
Produce clean cuts in nonmetallic hose, wood, and leather.
Save space in your shop by cutting, bending, and curving sheet metal with a single machine. Also known as shear brake rolls.