Protect your machinery if there is a jam, emergency stop, or other overload by cutting off torque between shafts when a maximum torque is reached. These torque limiters automatically resume transmitting torque once it drops below the set maximum. They should not be used in applications that frequently exceed the maximum torque. Since they come factory-set to a maximum torque, there’s no adjustment required and no risk of unintended changes to the torque setting.

They act as a flexible shaft coupling, so they reduce vibration and protect components from wear by compensating for angular and parallel misalignment. Fasten to your shafts by tightening the set screws, which bite into each shaft to hold it.

Sensor rings help you detect an overload by moving only when the limiter is transmitting torque. Use a sensor (not included) to trigger an alarm or shut down when the ring stops moving.

With zero backlash (no play), there’s no motion lost when these torque limiters transfer torque, so machines move smoothly with accurate and repeatable motion. They protect your machinery if there is a jam, emergency stop, or other overload by cutting off torque when a maximum torque is reached. They automatically resume transmitting torque once it drops below the set maximum. When they resume, they start transmitting torque from the same position where they stopped, keeping your drive and output sides in sync. They should not be used in applications that frequently exceed the set torque. You can adjust the set torque by using a spanner wrench to twist the adjustment ring.

To help you detect an overload, they have a sensor ring that moves out of place when these limiters cut off torque. Use a sensor (not included) to trigger an alarm or a shutdown when the ring moves.

They clamp evenly around your shaft for more holding power than set screws and won't damage your shaft.

Shaft-to-shaft torque limiters also act as a flexible shaft coupling, so they compensate for angular and parallel misalignment as they regulate torque transmission between shafts. This reduces vibration and protects components from wear. For a complete unit, you’ll need a torque limiter, a hub, and a spider (all sold separately).

Through-shaft torque limiters regulate torque transmission between an input shaft and a mounted component, such as a pulley, sprocket, or gear.

With rugged roller chains, these torque limiters handle more torque than other torque limiters. They have a disc that creates friction to prevent torque overload, control tension, and brake. If there’s too much torque, they’ll slip and only transmit the set torque. For example, they could be used in a machine that tightens a bottle cap to a certain torque without overtightening and breaking the bottle. Because they rely on friction, exposing them to moisture, oil, or lubricants can affect their performance. You can adjust the torque by rotating the hex nut on the hub.

They act as a flexible shaft coupling, so they reduce vibration and protect components from wear by compensating for angular and parallel misalignment. Fasten them to your shafts by tightening the set screws, which bite into each shaft to hold it.

Single-spring torque limiters let you make finer torque adjustments than double-spring torque limiters but can only withstand half as much torque.

Double-spring torque limiters handle twice as much torque as single-spring torque limiters but are not the best for making precise adjustments at low torques.

Prevent corrosion from interfering with these torque limiters’ ability to protect your machinery if there’s a jam, emergency stop, or other overload. Made of nylon, they won’t rust or corrode from moisture, salt, and oil. They cut off torque when they reach the set maximum torque and automatically resume transmitting torque once it drops below the set maximum. They should not be used in applications that frequently exceed the set torque. You can adjust the set torque by tightening the hex head screw on the housing.

To help you detect an overload, these torque limiters have a sensor ring that moves out of place when these limiters cut off torque. Use a sensor (not included) to trigger an alarm or a shutdown when the ring moves.

Fasten them to your shaft by tightening the set screws, which bite into the shaft to hold it.

Shaft-to-shaft torque limiters also act as a shaft coupling, allowing you to regulate torque transmission between two shafts.

Through-shaft torque limiters regulate torque transmission between an input shaft and a mounted component, such as a pulley, sprocket, or gear.

Spring kits let you change the torque range on your torque limiter.

Use your air system to remotely make changes to the torque setting or cut off torque completely, even during operation. Adjust the torque setting by adjusting the air pressure—the higher the pressure, the higher the set torque. When these torque limiters exceed their set torque, they’ll slip but still transmit the set torque. They use friction to prevent torque overload, control tension, and brake. They’re often used in automated systems. For instance, they can be used in a machine that tightens a bottle cap to a certain torque without overtightening it and breaking the bottle. Because they rely on friction, exposing them to moisture, oil, or lubricants can affect their performance.

Fasten them to your shaft by tightening the set screws, which bite into the shaft to hold it.

Shaft-to-shaft torque limiters also act as a shaft coupling, allowing you to regulate torque transmission between two shafts.

Through-shaft torque limiters regulate torque transmission between an input shaft and a mounted component, such as a pulley, sprocket, or gear.