With no moving parts, these solid state relays last longer, switch faster, and are quieter than mechanical relays. They interface between your controller and components to isolate input and output circuits, which protects components from voltage spikes, amplifies the relay’s signal, and reduces interference for reliable transmission. The relay’s LED indicator shines when it’s powered on, so you know at a glance which relays are wired correctly and what the switching position is. These relays are often used for switching small motors and sensors. Rated IP20, they prevent fingers and other objects from touching live circuits.

Mount them on 35 mm DIN rail (also known as DIN 3 rail) with the included socket. Relays disconnect from the socket for easy replacement.

Relays with spring-clamp terminals connect and disconnect to wires without needing to turn screws. With no screws to shake loose with vibration, these terminals hold tight over time.

For technical drawings and 3-D models, click on a part number.

With no moving parts, these solid-state relays are fast switching and require less maintenance, last longer, and are quieter than mechanical switches.

Relays with high-starting-current protection are designed with integrated circuits that prevent damage from the large burst of electricity when a device, such as a motor or pump, turns on.

Relays with LED indicator let you quickly spot whether a relay is on or off.

Heat sinks disperse heat to increase the relay’s current rating. Mount them to 35 mm DIN rail (also known as DIN 3 rail) for fast installation. They also mount to flat surfaces. Before mounting one-circuit relays, silicone compound or a thermal pad should be placed between the heat sink and relay. Silicone compound is sold separately for heat sinks that do not include it but require it. Two-circuit relays don’t require silicone for mounting.

Often used for high-speed switching at low-current levels, these solid state relays have no moving parts, so they switch faster, last longer, and are quieter than mechanical switches.

Heat sinks disperse heat to increase the relay’s current rating. Mount to 35 mm DIN rail (also known as DIN 3 rail) for fast installation. They also mount to flat surfaces.

Relay sockets mount directly on 35 mm DIN rail (also known as DIN 3 rail) for fast installation.

Relay sockets with screw terminals can also mount to a flat surface.

With no moving parts, these solid state relays require less maintenance and last longer, switch faster, and are quieter than mechanical relays. They can handle high starting (inrush) currents. The blade terminals meet ISO 8092-1 dimensions, ensuring they are compatible with the electrical connections in road vehicles you need to maintain or repair. Also known as ISO relays or automotive relays.

Often used to regulate the speed of AC fans or keep a heater at a set temperature, these relays connect directly to sensors to calculate and adjust output power. This allows you to use an analog input without converting it to a digital signal to control output power. They are solid state and have no moving parts, so they require less maintenance and last longer, are quieter, and switch faster than mechanical relays. IP20 rated, they have recessed terminals that prevent fingers and other objects from touching live circuits. An integrated heat sink disperses heat to increase the relay’s current rating. The LED indicator shows input voltage loss and internal relay faults, so you can easily check that your system is operating properly.

Mount them on 35 mm DIN rail (also known as DIN 3 rail) for fast installation. They also mount to flat surfaces.

All relays have phase-angle switching to accurately control all types of loads. This mode signals at non-zero voltage, which can produce electrical noise. Choose relays with full-cycle switching for resistive loads. This mode signals at zero voltage, so electrical interference is lower than phase-angle switching.

Single-phase relays can be set to switch every 1, 4, or 16 cycles. When used with infrared heaters, they have an option to switch at the half cycle and again at the full cycle. When switching at 16 cycles or at the half cycle, these relays have a soft-start option to increase the output slower in high-inrush current applications.

Three-phase relays switch every cycle.

Relays with a potentiometer input can connect to an external potentiometer for manual control.

Relays with over-temperature protection stop power when it gets too hot and keeps it off until the issue is resolved. Connect an auxiliary contact (not included) to signal an alarm or status controller.

Relays with short-circuit protection stop power if there is an open circuit, short circuit, or output voltage loss until the issue is resolved. Connect an auxiliary contact (not included) to signal an alarm or status controller.

For technical drawings and 3-D models, click on a part number.

Sealed coils protect these switches against moisture, heat, dirt, and mechanical and thermal stress. They have a solid state overload relay that extends motor life in demanding applications and protects it from overloads—starters will shut the motor off if current exceeds the full-load current rating. The relay is adjustable; set it for the exact overload current needed. All have auxiliary contacts to send a signal or connect to another device, such as an alarm or indicating light. Also known as NEMA starters.

Note: The full-load current rating of your motor must fall within the starter’s overload current range. Match input voltage, also known as coil voltage, to your control circuit; motor voltage may be different. Look for the full-load current rating on the motor’s faceplate, or estimate the current rating (given the motor’s horsepower and voltage).

NEMA contact sizes 0 and 1 are universal mount and fit Cutler-Hammer, GE, and Square D installations.

For technical drawings and 3-D models, click on a part number.